• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권2호
• /
• pp.123-129
• /
• 2000

This paper proposes a novel current control method of three-phase PWM rectifiers using estimated currents without phase current sensors. The phase currents are reconstructed from switching states of the rectifier and the measured dc output currents. To eliminate the calculation time delay effect of the microprosessor, the current at the next sampling instant are predicted by a predictive state observer and then are used for feedback control. Experimental results show that the control performance of the proposed system is almost the same as that of the phase current sensor-based system.

• E2M - 전기 전자와 첨단 소재
• /
• 제6권1호
• /
• pp.22-27
• /
• 1993

초전도 기기에 사용되는 고체 절연재료는 초전도 상태에서 상전도 상태로 천이시에 발생하는 임펄스 전압의 반복과전과 대전류에 의한 전자응력하에서 그 절연 성능이 충분히 발휘되어야 한다. 본 연구에서는 초전도 기기의 절연재료로 유력시되고 있는 결정성 PET에 임펄스 전압이 연속 과전될 때, 이 재료의 압축응력하에서의 절연강도특성에 미치는 연속과전의 효과를 검토하였다. 그 결과에 의하면 PET에 호모전하가 주입되면 임펄스 절연강도가 헤테로 전하주입시 보다 약 4MV/cm정도 높다. 한편, PET에 전하주입의 효과를 억제시킨 임펄스 진성절연강도는 압축응력의 증가와 함께 증가하여 최대치에 도달한 후 점차 감소하며 직류 절연강도 및 호모전하 주입시의 임펄스 절연강도보다 낮다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1433-1435
• /
• 2001

The mechanical and phase transformation of the cold isostatically pressed $\beta$-SiC ceramic were investigated as a function of the sintering temperature. The result of phase analysis revealed 6H, 4H, 3C and phase transformation between 3C and 4H showed over 2000$^{\circ}C$ and the $\beta$ ${\rightarrow}$ $\alpha$ phase transformation was in saturation at 2200$^{\circ}C$. The relative density and the mechanical properties of $\alpha$-SiC ceramic was increased with increased sintering temperature. The flexural strength showed the highest value of 230 MPa at 2200$^{\circ}C$. This reason is because crack was propagated through surface flaw. The fracture toughness showed the highest value of 4.2 $MPa{\cdot}m^{1/2}$ at 2200$^{\circ}C$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전력기술부문
• /
• pp.283-286
• /
• 2001

본 논문은 전력 품질개선장치인 DVR(Dynamic Voltage Restorer)시스템의 제어알고리즘 개발에 관한 것이다. DVR은 배전전계통에 직렬변압기를 통해 설치되어 전원의 순간전압강하(Voltage sag)를 보상하는 장치이며 전력변환장치 직렬변압기 에너지저장장치, 충전장치, 보호장치등으로 구성된다. 지락사고, 비선형부하의 순간투입, 뇌서지등 여러 요인에 의해 3상전원에서 발생하는 다양한 형태의 전압sag 보상이 가능한 제어알고리즘 모델을 제시하고 컴퓨터시뮬레이션을 통해 기본성능을 확인한 후 소형 DVR을 제작해 시험하였으며 이시험결과를 실 용량 DVR시제품의 설계에 이용하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1014-1017
• /
• 2003

열증착법을 이용하여 copper(II) phthalocyane (CuPc)의 박막을 제작하였다. 기판의 예열 온도를 달리하여 제작된 CuPc의 박막은 ${\alpha}-phase$와 ${\beta}-phase$로 구분할 수 있으며 phase에 따른 결정 구조를 관찰하기 위해 x-ray diffraction을 사용하고 peak의 위치를 관찰하였다. 또한 SEM, UV visible absorption spectra의 변화를 통해 온도에 따라 상전이가 이행해 가는 모습을 구체적으로 관측하였다. 이러한 결정 구조의 변화는 CuPc 박막의 전기전도 특성에 영향을 달리하여 유기발광 소자에 응용이 가능할 것으로 예상된다.

• 한국세라믹학회지
• /
• 제34권2호
• /
• pp.171-174
• /
• 1997

산소포논(phonon)이 Yttiria안정화 정방정 지르코니아 소결체(Yttria Stabilized Tetragonal Zirconia Po-lycrystals, Y-TZP)의 저온열화에 큰 영향을 미치는 사실을 실험적으로 밝혔다. Y-TZP의 저온열화 (정방정$\longrightarrow$단사정 상전이) 현상은 Y-TZP의 16O을 18O으로 치환함으로써 급격히 저하되었다. 이는 16O이 보다 무거운 18O으로 치환됨에 따라 임계변위 이상에서 산소원자가 존재할 확률이 감소하는 데 기인하는 것으로 설명하였다.

• 한국세라믹학회지
• /
• 제35권7호
• /
• pp.665-670
• /
• 1998

Ferroelectric anomaly in PbO-{{{{ { {B }_{2 }O }_{3 } }}-{{{{ {TiO }_{3 } }}-BaO glasses which is observed in DAT measurements was in-vestigated together with the effect of BaO content on the shift of Cuire temperature. The temperature where the ferroelectric anomaly apperars on cooling in DTA decreased in proportion with increasing BaO content,. For as-crystallized samples the ferroelectric anomaly was not observed on heating but on cooling whilist for powder samples leached chemically from the crystallized samples both endothermic and ex-otehrmic peaks were observed. This fact suggests that the appearance of the ferroelectric anomaly in DAT largely depends on glassy phases surrounding individual {{{{ {PbTiO }_{3 } }} crystals rather than effects of grain size and crystallinity.

• 한국세라믹학회지
• /
• 제28권2호
• /
• pp.160-166
• /
• 1991

Microstructure and phase changes during the sintering of ZnO varistors were studied in ZnO-Bi2O3-CoO-Sb2O3 and ZnO-Bi2O3-CoO-Sb2O3-Cr2O3 systems using acanning electron microscopy (SEM) with an energy dispersive X-ray analysis (EDAX), X-ray diffraction (XRD) and differential thermal analysis (DTA). The spinel phase and the Bi2O3 phase were formed by the decomposition of the pyrochlore phase during heating. The spinel particles (2-4$\mu\textrm{m}$), which were formed both along ther grain boundaries and within the ZnO grain, were always found near the pyrochlore phase. Intergranular phases (Bi2O3 and pyrochlore) were precipitated from the liquid phase during cooling. The Bi2O3 phases were located at the triple (or multiple) point of the ZnO grains. Cr2O3 played a role in decreasing the formation temperature of the spinel phase and Bi2O3 phase during sintering, and inhibited the grain growth.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.323-326
• /
• 2000

In this study, we used Brewster-Angle Microscope(BAM) to study on the molecular orientation of monolayer on the water surface. The behaviors of molecules on three different subphase have been observed. Reproducible $\pi$-A isotherm have been obtained only on information about phase transition by molecular area. BAM facilitates the observation of morphology by optical anisotropy and thickness in monolayer and multilayers as BAM is shown to be sensitive to anisotropy of film. Every transition was found by BAM technique, either as a dramatic change in degree of contrast or as a sudden alteration of molecular action and $\pi$-A isotherm.

• 한국전기전자재료학회논문지
• /
• 제21권10호
• /
• pp.943-949
• /
• 2008

We report on the development of transition edge sensors for x-ray detection. The sensor technology was based on the fabrication of a superconducting film on a thin membrane. A bilayer of a superconductor, Ti, and a noble metal, Au, was e-beam evaporated on a micromachined SiNx. Another Au layer was evaporated on the two side edges of the bilayer in order not to be affected by structural imperfections at the boundaries. With the method described in the present report, the superconducting transition temperature of the device was consistently achieved to near 80 mK with a sharp transition. The energy spectrum ueasured with the device provided 37 eV FWHM for 5.9 x-rays. We also discuss the design and fabrication considerations as well as the performance of the device in detail.