• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.533-542
• /
• 2016

We investigate fluidization characteristics of the mixture of rice husk, silica sand and rice husk ash as a preliminary study for valuable utilization of rice husk ash obtained from gasification of rice husk in a fluidized bed reactor. As experiment valuables, the blending ratio of rice husk and sand (rice husk: sand) is selected as 5:95, 10:90, 20:80 and 30:70 on a volume base. Rice husk ash was added with 6 vol% of rice husk for each experiment and air velocity to the reactor was 0~0.63 m/s. In both rice husk/sand and rice husk/sand/ash mixture, the minimum fluidization velocity (Umf) is observed as 0.19~0.21 m/s at feeding of 0~10 vol.% of rice husk and 0.30 m/s at feeding of 20 vol.% of rice husk. With increasing the amount of rice husk up to 30 vol.%, $U_{mf}$ can not measure due to segregation behavior. The mixing index for each experiment is determined using mixing index equation proposed by Brereton and Grace. The mixing index of the mixture of rice husk/sand and rice husk/sand/ash was 0.8~1 and 0.88~1, respectively. The optimum fluidization condition was found for the good mixing and separation of rice husk ash.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.349-354
• /
• 2009

In this study, a bubbling fluidized-bed reactor was used to study $CO_2$ capture from flue gas using a potassium-based dry sorbent. A dry sorbent, manufactured by the Korea Electric Power Research Institute, consists of 35% of $K_2CO_3$ for $CO_2$ absorption and 65% of supporters for mechanical strength. $H_2O$, a reactant of the carbonation reaction, was supplied in the reactor as a form of saturated water vapor at a given temperature. The experiment of the regeneration reaction was performed by raising up to a given temperature using $N_2$ as a fluidization gas. It was indicated that sorption capacity and regenerability of dry sorbents showed high-efficiency at $1.97\;mol\;H_2O/mol\;CO_2$ and $400^{\circ}C$, respectively. The regenerated sorbent samples were analyzed by TGA to confirm the extent of the reaction. When the regeneration temperature was $150^{\circ}C$, the regenerability of dry sorbents was about 60%, which was capable of applying those sorbents to a two-interconnected fluidized-bed reactor system with continuous solid circulation. The results obtained in this study can be used as basic data for designing and operating a large scale $CO_2$ capture process with two fluidized-bed reactors.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.4
• /
• pp.283-288
• /
• 2013

To evaluate the ability of the submerged plant, Ceratophyllum demersum's (C. demersum) to remove nutrients and to inhibit growth of cyanobacteria, a total of 6 mesocosms were conducted in a batch reactor for 9 days. From the 84 hr of the experiment, C. demersum was stabilized and showed daily cycle trends according to changes in pH and DO levels. The concentration of nutrients, $NH_3{^+}$, $NO_3{^-}$ and $PO_4{^3}$ continuously decreased until 9 days of the experiment, with the rapid decrease in nutrient concentration for the first 24 hours. High correlation coefficient ($r^2{\geq}0.96$, p<0.001) between the amount of C. demersum's biomass per unit area and the nutrients removal level were derived, and greater C. demersum's biomass per unit area showed higher removal efficiency of nutrients. However, there were differences in the C. demersum's activity level between batch reactors with higher and similar density of the C. demersum, but nonetheless water purification effect appears to have a significant influence due to attached algae and microorganisms. The growth rate of harmful cyanobacteria, Microcystis aeruginosa (M. aeruginosa) with C. demersum's density of 2,500 g $fw/m^2$ (100% of cover degree) was 0.31 /day, compared to the growth rate of 0.47 /day for the control group (0% of cover degree). In terms of number of cells, the control group had 1.7 times higher number of cells than the experimental group, proving that C. demersum has the ability to inhibit the growth of harmful cyanobacteria.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.36-44
• /
• 2007

The purpose of this study was to investigate thermal stability, reactivity, and bonding strength of existing epoxy resin mixed with the epoxidized soybean oil (ESBO) in order to use soybean oil economically. In the dry shear test, the marked strengths showed $30.5kgf/cm^2$ at the ratio of ESBO to epoxy resin 9 : 1 and $6.2kgf/cm^2$ at the ratio 8 : 2. The bonding strengths of the others, except mixing ratios 2 : 8 and 1 : 9, exceeded the requirement of Korean plywood standard of $7.0kgf/cm^2$. In the wet shear test, the result was $5.8kgf/cm^2$ at the ratio 9 : 1. There were no thickness swelling and moisture absorption in the water resistance of the film. The value of activation energy, Tg (${\Delta}E$), by DSC analysis showed between $110^{\circ}C$ and $120^{\circ}C$ through all ratios. Epoxy in the epoxy resin fully reacted with the hardener (TETA), but it is difficult to decide that epoxys in the ESBO were reacted directly with the hardener from FT-IR analysis. As the mixing ratio of ESBO increased, the thermal stabilities dropped from TGA analysis. From the comprehensive view on the results of above experiments, it could be confirmed through experiments that the ESBO in the mixed adhesive of epoxy resin/ESBO played a role as an extending agent level of epoxy adhesive, and we were able to know that in order to utilize ESBO as an adhesive, a study should be performed on the condition of hardening, inducible of the hardening reaction.

• Tunnel and Underground Space
• /
• v.30 no.4
• /
• pp.359-381
• /
• 2020

Within the framework of DECOVALEX-2019 Task D, full-scale engineered barriers experiment (FEBEX) at Grimsel Test Site was numerically simulated to investigate an applicability of implemented Barcelona basic model (BBM) into TOUGH2-MP/FLAC3D simulator, which was developed for the prediction of the coupled thermo-hydro-mechanical behavior of bentonite buffer. And the calculated heater power, temperature, relative humidity, total stress, saturation, water content and dry density were compared with in situ data monitored in the various sections. In general, the calculated heater power and temperature provided a fairly good agreement with experimental observations, however, the difference between power of heater #1 and that of heater #2 could not captured in the numerical analysis. It is necessary to consider lamprophyre with low thermal conductivity around heater #1 and non-simplified installation progresses of bentonite blocks in the tunnel for better modeling results. The evolutions and distributions of relative humidity were well reproduced, but hydraulic model needs to be modified because the re-saturation process was relatively fast near the heaters. In case of stress evolutions due to the thermal and hydraulic expansions, the computed stress was in good agreement with the data. But, the stress is slightly higher than the measured in situ data at the early stage of the operation, because gap between rock mass and bentonite blocks have not been considered in the numerical simulations. The calculated distribution of saturation, water content, and dry density along the radial distance showed good agreement with the observations after the first and final dismantling. The calculated dry density near the center of the FEBEX tunnel and heaters were overestimated compared with the observations. As a result, the saturation and water content were underestimated with the measurements. Therefore, numerical model of permeability is needed to modify for the production of better numerical results. It will be possible to produce the better analysis results and more realistically predict the coupled THM behavior in the bentonite blocks by performing the additional studies and modifying the numerical model based on the results of this study.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.1
• /
• pp.52-60
• /
• 2006

This study investigated how wood properties (i.e., annual rings, sapwood, heartwood, and cracks) might affect preservative treatment in Japanese larch (Larix leptolepis) round-wood product. We specially focused on small-diameter (~10 cm diameter) wood that is commercially sold in market. Among 100 wood samples, the groups of sample with 13~16, 17~20 annual rings represented 33 and 27 in each frequency, while 2~3 and 4~5 mm annual ring width accounted for 72 and 68 in frequency. More than a half (54%) of wood samples contained a mix of heartwood and sapwood in its surface. The rest (46%) had only heartwood exposed in the wood surface. A wide range of checks were showed in the wood samples, but the highest frequency was observed in samples with 1~6 surface (1~14 mm in size) checks and 1~4 end-grain (8~14 mm in size) checks in each round-wood sample. Pressure treatment resulted in a wide range of penetration of ACQ (Alkaline Copper Quat) into the wood, showing $4.3{\pm}4.19mm$ penetration in the wood samples contained a mix of heartwood and sapwood in its surface. However preservative treatment was much less effective for the heartwood only wood samples, ranging average 1.3 mm with ACQ and 1.1 mm with CCA (Chromated Copper Arsenate). These penetration results shown in heartwood samples did not meet the penetration standard that is required for H3 by the Korean Forest Service in relation to wood preservation treatment. These low penetration results were not significantly improved even if we incised wood samples to improve treatment effect, showing only small increase of 0.7 mm with ACQ and 0.6 mm with CCA. When preservative treatment was tested with heartwood, penetration of preservatives decrease with increase of annual rings per a cross-section area (r=0.5345). We also found that the length and number of check had no effect on preservative treatment, showing r=0.1301 and r=0.1802, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.1
• /
• pp.21-44
• /
• 1988

As a way for the effective utilization of pallman chips and sawdusts, these furnish materials were combined with non-woody material of plastic (polypropylene) screen in board manufacturing to improve their weak physical and mechanical properties. The conventional boards were made with conditions of specific gravity 0.40, 0.55, 0.70, and 0.85, resin content 8, 10, 12 and 14%, and number of polypropylene screen 1, 2, 3 and 4, and press-lam boards were also manufactured. The physical and mechanical properties were measured and discussed on thickness swelling, bending modulus of rupture and elasticity, tensile strength, internal bond strength, and screw holding strength. The results obtained at this study were summarized as follows: 1. In thinckness swelling both of pallman chip board and sawdust board were improved by the increase of resin content, and press-lam boards showed lower thickness swelling than conventional boards. 2. Both the modulus of rupture and elasticity were increased with the increase of specific gravity, and press-lam boards showed higher modulus of rupture and elasticity than conventional boards. On the other hand, modulus of rupture was increased with the increase of number of polypropylene screen and resin content whereas these effects in modulus of elasticity was not recognized. 3. Tensile strength was increased with the increase of specific gravity, and the boards combined with polypropylene screen showed higher tensile strength than control boards. Also tensile strength was increased with the increase of number of polypropylene screen, and press-lam boards revealed higher tensile strength than conventional boards. 4. Internal bond strength was increased with the increase of specific gravity, and the boards combined with polypropylene screen were lower in internal bond strength than control boards. Also, the boards combined with odd number of polypropylene screen showed lower internal bond strength than those combined with even number of polypropylene screen. 5. Screw holding strength was increased with the increase of resin content and specific gravity but significant difference was not approved between boards combined with polypropylene screen and control boards. In press-lam boards, pallman chip boards of higher specific gravity but sawdust boards of lower specific gravity showed better screw holding strength than control boards.

• Korean Journal of Animal Reproduction
• /
• v.25 no.2
• /
• pp.125-130
• /
• 2001

This study was performed to report a direct dose dependent stimulatory effect of the Flavonoid(F) on basal testosterone secretion and a dose dependent effect on LH induced testosterone production by Leydig cell of matured rats in vitro culture. F was obtained kom the Rhus vernicifua through aceton extraction and silica gel adsorption column chromatography. Leydig cells (1$\times$10$^{6}$ cells/well) from 12 weeks old rats were incubated with or without F(0, 20, 40, 80, 160 ng) or insulin-like growth factor-I(IGF-I) in the presence or absence of LH(10, 100ng). 1. The maximal stimulatory concentrations of testosterone in culture media were showed at 24hr of culture. but these testosterone level were decreased at 36 hr of culture. 2. Flavonoid(80ng) were significantly(P ＜ 0.05) increased testosterone production compared with control groups for 12 hr culture. 3. Testosterone secretion by Leydig cells stimulated with LH(10, 100ng) for 6 hr and 12hr culture compared with 3 hr culture. 4. LH 10 ng augmented testosterone were increased by addition of F 40 ng for 12 hr culture. 5. F(0 and 40 ng) also enhanced LH 10 ng stimulated testosterone for 3 hr Leydig cells culture. 6. Addition of IGF-I 100 ng to the culture medium for 6 hr were increased the concentration of testosterone by Leydig cells stimulated with 100 ng LH. These results indicate that Flavonoid has a direct stimulatory effect on basal testosterone secretion in rat Leydig cells, and also modulates LH mediated testosterone. Therefore, Flavonoid may act as a modulator on gonadal development or gonadal steroidogenesis in direct or indirect.

• Economic and Environmental Geology
• /
• v.35 no.5
• /
• pp.395-406
• /
• 2002

The sixty natural springs and community wells used as a drinking water in the Daejeon area are mainly located at the parks and the natural green districts. The purpose of this study is to investigate the characteristics of water quality and the contamination of the springs and the wells, and to suggest the management strategy for the springs and wells. For this study, we undertook water quality data from Daejeon City. According to the statistic analysis of water quality data, unacceptable rate as a drinking water was about 28 percent in 1999 and 24.5 percent in 2000, respectively. Major unacceptable factor is coliform, and others are bacteria, yersinia, color, turbidity, Fe and F. The unacceptable rate shows a roughly positive relationship with precipitation, that is, it shows highest rate during a rainy season between June and September. The major contamination source is likely to be the excrement of wild animals around natural springs and wells. Most of springs are vulnerable to the contamination of coliform and bacteria because of short residence time and shallow circulation in subsurface environment. The water samples collected from 31 springs or wells show weak acidic pHs, the electrical conductivity ranging from 63 to 357 $\mu\textrm{S}$/cm, and the hydrochemical types of Na(Ca)-HC0$_3$ and Ca-HC0$_3$. The groundwater samples of low total dissolved solid(TDS) belong to Na(Ca)-HC0$_3$. type, and the groundwater of high total dissolved solid is shifted towards Ca-HC0$_3$ type in the chemical composition. These hydrochemical characteristics indicate that most natural springs is in the early stage of geochemical evolution. The natural springs should be closed during a rainy season, which shows a high contamination rate. We suggest that a protection barrier around the springs should be built to keep wild animals away from the springs.

• Ecology and Resilient Infrastructure
• /
• v.7 no.2
• /
• pp.126-133
• /
• 2020

In accordance with the implementation of the sunset provision to cancel the designations of urban park sites that remained unexecuted for a prolonged period until 2020, the park sites in the city center, which account for 90% of the long-term unexecuted urban facilities subjected to the provision, are currently on the verge of development. The total area of the 204 park sites that will disappear in Seoul as a result of this provision is 95 ㎢; moreover, 116 of these are privately-owned. It is expected that the possible changes in the use of these park sites could result in reckless development and reduction of green space, which would ultimately affect the ecosystem. This study applied the InVEST model to calculate the changes in the fixed carbon amount before and after the implementation of the sunset provision to estimate the economic value of these changes. The study focused on Jongno-gu in Seoul because it has the most unexecuted park sites subjected to the lifting of the designation. The research findings show that the fixed carbon amount provided by the unexecuted park sites in Jongno-gu was 374,448 mg, prior to the implementation of the sunset provision; however, the amount was estimated to decrease by 18% to 305,564 mg after its execution. When calculated in terms of average value of the real carbon price, this translated into a loss of approximately 700 million won. In addition, considering the social costs including both climate change and the impact on the ecosystem, an economic loss of approximately 98 billion won was projected. This study is meaningful because its predictions are based on the estimation of fixed carbon amount according to the implementation of the sunset provision in Jongno-gu and scientifically calculates the value of ecological services provided by the parks in the city. This study can serve not only as a basis during the decision-making process for policies related to ecosystem conservation and development, but also as an evidentiary material for the compensation of privately-owned land that is designated as urban park sites and was unexecuted for a prolonged period.