• Nuclear Engineering and Technology
• /
• v.20 no.1
• /
• pp.9-18
• /
• 1988

Previously determining the fuel loading pattern is based on the trial and error method. For a candidate pattern, the core analysis is performed and the pattern is examined whether it satisfies the imposed constraints such as the power peaking or not. The pattern, then, is revised by the shuffling of assemblies and the revision is repeated until all of the conditions are met. This method unavoidably requires many iterative diffusion calculations, computing times and accumulated experiences. To overcome these disadvantages, a new method which is called backward diffusion calculation is introduced. If the most desirable power distribution is already known, the optimal loading pattern can be obtained by solving the backward diffusion equation with simple calculation. In this study, the basic equation for the backward diffusion calculation is derived and the optimal power and fuel distributions are searched in one-dimensional cylindrical geometry by using the proposed method. In addition, the basis to determine the optimal power and fuel distributions is suggested for the real core geometry.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4673-4678
• /
• 2011

In this paper, studies on a mixing characteristic and viscosity measurement of polymer/graphite composites for a bipolar plate of the polymer electrolyte membrane fuel cell were presented. Since the materials for the bipolar plate should be electrically conductive, contents of solid graphite in the composite are very high. As a consequence, a viscosity of the polymer/graphite composite used for the bipolar plate is very high and the measurement of the viscosity is difficult. Viscosity measurements of the polymer/graphite composites were not possible because pressure drops were continuously fluctuated during the viscosity measurements when a conventional capillary die was used. After the die design was optimized, the steady state pressure drop could be achieved, but the viscosity thus measured was not reproducible. After many trials with different experimental techniques, it was found that melt blending of the grinded powder mixtures of both PET and graphite provides reproducible viscosity measurements and electric conductivities of the polymer/graphite composites.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.571-576
• /
• 1998

This study was carried out for investigating the corrosion behaviors, corrosion mechanisms, and behaviors of elements on a separator for a molten carbonate fuel cell under both the electrolyte and anode side environment. A 310S austenitic stainless steel was used as the separator material. Corrosion proceeded via three steps; the formation step of corrosion product in which rapid corrosion takes place until stable corrosion product is formed after the beginning of corrosion, the protection step against corrosion until breakaway occurs after the formation step of stable corrosion product and the advancing step of corrosion after the breakaway. From the standpoint of the behavior of the elements in the specimen, Fe and Cr, Ni were enriched in the region of corrosion product, in the region of corrosion protection, and at the Cr-deplete zone, respectively. With respect to corrosion mechanism, ionization of electrolyte at the anode side was the main corrosion mechanism, and the final corrosion products were $LiFeO_2$ and $LiCrO_2$ at the anode side.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.3
• /
• pp.212-216
• /
• 2003

The humidification measurement system designed in laboratory was used to measure relative humidity and temperature of reaction gases passing through internal or external humidifier which was used in proton exchange membrane fuel cell test station. The relative humidity of gases was stabilized after $10\~20$ minutes and thus credibility of data could be assured. The effect of relative humidity on fuel cell performance could be analyzed by humidity measurement system. Extreme caution was needed to avoid humidity sensor mal-function or failure which is probable in experiment of high humidity condition near $100\%$. The amount of water carried by gas through humidifier was increased along the flow rate of gas. However, the extent of increase was lowered at high gas flow rate. These phenomena could be analyzed as residence time effect of gas in humidifier.

• Journal of the Korean Institute of Gas
• /
• v.15 no.2
• /
• pp.15-20
• /
• 2011

Although CNG is able to meet the current emission standards, it is expected to be impossible to satisfy the requirements of the next EURO-6 emission regulation without an additional after-treatment device. Hydrogen is known to be a gaseous fuel which features the wide flammability limit and the fast reactivity. A certain amount of hydrogen addition to CNG is able to extend the lean combustion range and produce lesser amounts of harmful emissions. In this research, the combustion and emission characteristics of HCNG(mixture of Hydrogen and CNG) fuel were experimented in an 11-liter heavy duty lean burn engine varying hydrogen contents, air-to-fuel ratio and spark timing. The optimization of this HCNG engine for a city bus was performed through the evaluations of oxidation catalyst characteristics.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.187-190
• /
• 2012

Contamination of ion from cathode air on the membrane and electrode assembly (MEA) is the serious degradation source in proton exchange membrane fuel cells (PEMFC). In this study, concentration of ions in air at industry region, street and seaside were measured. There were comparably high concentration of $Na^+$, $K^+$, $Ca^{2+}$ and $Fe^{3+}$ in this regions. This paper shows the effects of MEA contamination by these ions generated from humidification water. After 170 hours of fuel cell operation using city water as humidification water, the performance of unit cell decrease to 11% of initial performance. The electrolyte membrane easily absorbed foreign contaminant cations due to the stronger affinity of foreign cations with the sulfonic acid group compared to $H^+$. The contaminant ions existing in the interface between the platinum catalyst and ionomer layer turn out to be the most serious factor to decrease cell performance.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.95-104
• /
• 2003

This paper deals with the analytic and FEM analyses of sloshing frequency response of incompressible, invicid and irrotational flow in two dimensional rectangular tank. We use Laplace equation based on potential theory as governing equation. For small amplitude sloshing motion, the linearized free surface condition was applied and the analytic solution as obtained by the separation of variables. To simulate the effect of the energy dissipation due to viscous damping, artificial viscous coefficient is introduced and the divergence of response at resonance frequencies may be avoided by this coefficient. This problem was solved by FEM using 9-node elements in order to predict the maximum amplitude of sloshing response. Numerical results of free surface height, fluid pressure and fluid force show good agreement with those by analytic solution. After verifying the test FEM program, we analyze the frequency response characteristics of sloshing to the fluid height.

• Resources Recycling
• /
• v.20 no.2
• /
• pp.67-73
• /
• 2011

In this study, for recovery of renewable noble metal from used stack of fuel cell, synthesis of platinum nano particle is established through effect of platinum solution concentration, pH value, reducing agent and dispersing agent at a volume ratio of 1 mM $H_2PtCl_6$:10 mM $NaBH_4$:8 mM Cl4TABr = 1:0.4:0.4(vol.%), pH4, $50^{\circ}C$, 160 rpm and 10min. Less than 5 nm platinum particles were synthesized using Pt leaching solution from used MEA of stack under same condition of method using simulated Pt solution. The characteristics of synthesized nano particles was illustrated by XPS analysis as the reduction of platinum ions into platinum metals(zero-valent).

• Fire Science and Engineering
• /
• v.33 no.1
• /
• pp.23-29
• /
• 2019

Rechargeable battery such as lithium-ion battery has been noticed as a kinds of the energy storage system in the recent energy utilization and widely used actually in various small electronic equipment and electric vehicles. However, many thermal runaway caused battery accidents occurred recently, which still is obstacle for advanced application of lithium ion battery. One of the main differences to general fires is the existence of ionized electrolyte with electron during combustion. Therefore, we simply simulated the ion addition effects of battery fires by introducing an ionized fuel in jet diffusion flames. When the ionized methane through a corona discharge was used as fuel, the overall flame stability and shape such as flame length showed no significant difference from normal methane flame, but NOx and CO emissions measured at the post flame region decreased. The ion addition effect of methane oxidation was also numerically simulated with the modeling of hydrogen addition in the mixture. It was confirmed that the hydrogen addition at a fixed temperature had a similar effects on ionization of methane and hence could be modeled successfully.

• Journal of Power System Engineering
• /
• v.11 no.2
• /
• pp.5-11
• /
• 2007

액화천연가스(LNG : Liquified Natural Gas)는 연료로 사용하기 위하여 기화하는 과정을 거치게 되는데 기화하는 방식에는 해수에 의한 기화와 공기에 의한 기화의 두 가지 방식으로 나뉘게 된다. 해수에 의한 기화는 LNG 인수기지에서 대량의 LNG를 NG로 기화하기 위하여 사용하며, 공기에 의한 기화는 LNG 위성기지에서 사용처에 적합한 온도를 얻기 위해서 일반적으로 많이 사용하고 있는 공기식 기화기를 이용하여 기화를 하는 방식을 취하고 있다. LNG가 NG로 기화하는 과정에서 1kg당 200kcal의 냉열을 외부로 방출하고 있으며, 이러한 냉열의 방출로 인하여 공기식 기화기의 표면에 결빙현상을 발생시킨다. 또한 현재 사용하고 있는 기화기는 $2{\sim}3$개의 기화기를 연결하여 사용하고 있어 그 비용의 손실이 크다고 할 수 있다. 그리하여 본 연구는 최근 사용빈도가 증가하고 있는 공기식 기화기에 관한 것으로 작동유체는 실제 LNG와 특성이 비슷한 초저온 액화가스인 $LN_2$를 사용하였다. 이번 연구에 사용된 변수는 다음과 같다. 첫째, 각각의 기화기의 길이를 4000mm, 6000mm, 8000mm으로 하였고 핀의 type을 finless, 4fin, 8fin으로 하여 적용하였다. 두 번째는 봄, 여름, 가을, 겨울철에 따른 기화기의 성능을 알고자 각각의 계절별 온도와 습도를 적용하였다. 마지막으로 계절별 풍속과 실험을 하는 시간 동안의 유량을 알고자 압력을 1 bar로 적용하였다. 그리하여 이번 연구의 목적으로는 각각의 변수를 통하여 실험을 진행 한 후 vaporizer type과 길이에 대한 최적의 성능을 가지는 기화기에 대한 자료를 제시하고자 한다.기성분은 균주에 따른 약간의 차이가 있었으나 경향은 비슷하게 나타났다. 이상의 결과 알코올 발효 균주에 따른 참다래 와인의 이화학적 품질특성에는 큰 차이가 없었으나 고급알코올함량을 비교하였을 때 Sacch. cerevisiae Wine 3이 와인제조에 가장 적합한 것으로 평가되었다.장 낮은 값을 나타내었으며, 홍국의 함유량이 증가할수록 유의적으로 증가하였다. b값은 CSB가 가장 낮은 값을 나타내었으며, 홍국의 함유량이 증가할수록 유의적으로 증가하였다. 물성측정 결과 경도와 응집성은 각 시료들 간의 유의적인 차이가 나타나지 않았다. 탄력성과 부서짐성은 CSB가 가장 낮았으며, 홍국의 함유량이 증가할수록 증가하였다. 점착성은 SDB1이 가장 낮았으며, 홍국의 함유량이 증가할수록 증가하였다. 관능검사 결과 기공의 균일성은 SDB1이 가장 균일한 것으로 나타났으며, 색은 홍국의 함유량이 증가할수록 높게 나타났다. 경도, 탄력성, 단맛 및 신맛 등은 홍국 함유량이 증가할수록 증가하는 것으로 나타났다. 이취는 SDB1이 가장 적게 나는 것으로 나타났으며, 전반적인 기호도는 SDB1이 가장 높았다. 따라서 홍국을 10% 첨가한 sourdough starter를 3일 동안 발효한 후 반죽에 첨가하여 sourdough bread를 제조할 때 품질이 가장 우수한 제품을 얻을 수 있었다.생수와 여러 물질의 혼합용액의 온도가 장에 끼치는 자극에 차이가 있지 않나 추측되며 이에 관한 추후 연구가 요망된다. 총대장통과시간의 단축은 결장 분절 모두에서 줄어들어 나타났으나 좌측결장 통과시간의 감소 및 이로 인한 이 부위의 통과시간 비율의 저하가 가장 주요하였다. 이러한 결과는 차가운 생수 섭취가 주로 결장 근위부를 자극하는 효과를 발휘하는 것이 아닌가