• Journal of Advanced Navigation Technology
• /
• v.20 no.5
• /
• pp.401-407
• /
• 2016

This paper introduces 3-dimensional path planning and guidance including power model for high altitude long endurance (HALE) UAV using solar energy. Dubins curve used in this paper has advantage of being directly available to apply path planning. However, most of the path planning problems using Dubins curve are defined in a two-dimensional plan. So, we used 3-dimensional Dubins path generation algorithm which was studied by Randal W. Beard. The aircraft model which used in this paper does not have an aileron. So we designed lateral controller by using a rudder. And then, we were conducted path tracking simulations by using a nonlinear path tracking algorithm. We generate examples according to altitude conditions. From the path tracking simulation results, we confirm that the path tracking is well on the flight path. Finally, we were modeling the power system of HALE UAVs and conducting path tracking simulation during 48hours. Modeling the amount of power generated by the solar cell through the calculation of the solar energy yield. And, we show the 48hours path tracking simulation results.

• Journal of Advanced Navigation Technology
• /
• v.24 no.1
• /
• pp.16-27
• /
• 2020

This paper investigates the applicability of optical flow information for unmanned aerial vehicle (UAV) navigation under environments where global navigation satellite system (GNSS) is unavailable. Since the optical flow information is one of important measurements to estimate horizontal velocity and position, accuracy of the optical flow information must be guaranteed. So a navigation algorithm, which can estimate and cancel biases that the optical flow information may have, is suggested to improve the estimation performance. In order to apply and verify the proposed algorithm, an integrated simulation environment is built by designing a guidance, navigation, and control (GNC) system. Numerical simulations are implemented to analyze the navigation performance using this environment.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.1
• /
• pp.59-70
• /
• 2022

In this paper, we proposed an active fault tolerant control (AFTC) method for the position control of a quadrotor with complete loss of effectiveness of one motor. We obtained the dynamics of a quadrotor using Lagrangian equation without small angle assumption. For detecting the fault on a motor, we designed a fault detection module, which consists of the fault detection and diagnosis (FDD) module and the fault detection and isolation (FDI) module. For the FDD module, we designed a nonlinear observer that observes the states of a quadrotor based on the obtained dynamics. Using the observed states of a quadrotor, we designed residual signals and set the appropriate threshold values of residual signals to detect the fault. Also, we designed an FDI module to identify the fault location using the designed additional conditions. To make a quadrotor track the desired path after detecting the fault of a motor, we designed a fault tolerant controller based on the multiple sliding surface control (MSSC) technique. Finally, through simulations, we verified the effectiveness of the proposed AFTC method for a quadrotor with complete loss of effectiveness of one motor.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.8
• /
• pp.859-866
• /
• 2009

The article discusses an issue of estimating the airspeed of an autonomous flying vehicle. Airspeed is the difference between ground speed and wind speed. It is desirable to know any two among the three speeds for navigation, guidance and control of an autonomous vehicle. For example, ground speed and position are used to guide a vehicle to a target point and wind speed and airspeed are used to maximize flight performance such as a gliding range. However, the target vehicle has not an airspeed sensor but a ground speed sensor (GPS/INS). So airspeed or wind speed has to be estimated. Here, airspeed is to be estimated. A vehicle's dynamics and its dynamic parameters are used to estimate airspeed with attitude and angular speed measurements. Kalman filter is used for the estimation. There are also two major sources arousing a robust estimation problem; wind speed and altitude. Wind speed and direction depend on weather conditions. Altitude changes as a vehicle glides down to the ground. For one reference altitude, multiple model Kalman filters are pre-designed based on several reference airspeeds. We call this group of filters as a cluster. Filters of a cluster are activated simultaneously and probabilities are calculated for each filter. The probability indicates how much a filter matches with measurements. The final airspeed estimate is calculated by summing all estimates multiplied by probabilities. As a vehicle glides down to the ground, other clusters that have been designed based on other reference altitudes are activated. Some numerical simulations verify that the proposed method is effective to estimate airspeed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.7
• /
• pp.637-648
• /
• 2007

This paper presents a sensor fusion method based on indirect Kalman filter(IKF) for error compensation of low-cost inertial sensors and its application to the determination of attitude and position of small flying robots. First, the analysis of the measurement error characteristics to zero input is performed, focusing on the bias due to the temperature variation, to derive a simple nonlinear bias model of low-cost inertial sensors. Moreover, from the experimental results that the coefficients of this bias model possess non-deterministic (stochastic) uncertainties, the bias of low-cost inertial sensors is characterized as consisting of both deterministic and stochastic bias terms. Then, IKF is derived to improve long term stability dominated by the stochastic bias error, fusing low-cost inertial sensor measurements compensated by the deterministic bias model with non-inertial sensor measurement. In addition, in case of using intermittent non-inertial sensor measurements due to the unreliable data link, the upper and lower bounds of the state estimation error covariance matrix of discrete-time IKF are analyzed by solving stochastic algebraic Riccati equation and it is shown that they are dependant on the throughput of the data link and sampling period. To evaluate the performance of proposed method, experimental results of IKF for the attitude determination of a small flying robot are presented in comparison with that of extended Kaman filter which compensates only deterministic bias error model.

• Journal of Aerospace System Engineering
• /
• v.11 no.1
• /
• pp.1-7
• /
• 2017

While a satellite is carried into orbit by a launch vehicle, it is exposed to the severe launch environment with random vibrations and shock. Accordingly, these vibration sources affect electronic equipment, particularly the printed circuit board (PCB) in the satellite. When the launch load impacts the PCB, it causes negative behavior. This causes perpendicular bending around the boundary of fixation points that finally leads to the failure of solder joints, lead wires, and PCB cracks. To overcome these issues, the electronic equipment design must meet reliability requirements. In this paper, Steinberg's method is used to derive allowable and maximum deflection to verify design from a life perspective concerning the control board of the Antenna Pointing Driver (APD) mounted on KOMPSAT-3.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.7
• /
• pp.100-111
• /
• 2003

The HAUSAT-1(Hankuk Aviation University SATellite-1) will orbit at the altitude of 650km-800 km with 65 or 98 degree inclination angle. The effects of magnetic field and Earth gravity are more predominant than other space disturbances because the HAUSAT-1 will be positioned in LEO(Low Earth Orbit). The HAUSAT-1 design implements a magnetic control system and gravity-stable system which implement the solar panel deployment system. The simulation using MATLAB was performed to make sure the attitude stability of HAUSAT-1, which is based on the 8th order magnetic field model and non-linear equations of disturbances and the HAUSAT-1 attitude. The stability is investigated for two different HAUSAT-1 configurations and attitude which are affected by disturbances through simulation. The results for gravity-gradient stable and non gravity-gradient stable system are compared. Methodology of attitude stabilization was explored to develop an effective attitude control system for the HAUSAT-1 using magnetic torquers.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.4
• /
• pp.357-367
• /
• 2021

This paper studies the simulations of active airframe vibration controls for the Sikorsky X2 helicopter with a lift-offset coaxial rotor. The 4P hub vibratory loads of the X2TD rotor are obtained from the previous work using a rotorcraft comprehensive analysis code, CAMRAD II. The finite element analysis software, MSC.NASTRAN, is used to model the structural dynamics of the X2TD airframe and to analyze the 4P vibration responses of the airframe. A simulation study using Active Vibration Control System(AVCS) with Fx-LMS algorithm to reduce the airframe vibrations is conducted. The present AVCS is modeled using MATLAB Simulink. When AVCS is applied to the X2TD airframe at 250 knots, the 4P longitudinal and vertical vibration responses at the specified airframe positions, such as the pilot seat, co-pilot seat, engine deck, and prop gearbox, are reduced by 30.65 ~ 94.12 %.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.3
• /
• pp.253-259
• /
• 2007

Standard design and suitable environmental test method should be applied to increase the reliability of UAV flight control systems. UAV flight control systems under development domestically have enough capabilities for complicated missions. However, most low cost systems are not designed with concepts of compatibility, adaptability, and environmental compliance. This paper explains ATR(Air Transport Rack) standard that is widely used on aircraft. The paper presents a design uses commercial off-the-shelf parts. The paper also presents various environmental standards for airborne equipments, including U.S. military specifications. The developed FCS was tested under these specifications. The paper shows the test procedures and results.

• Geophysics and Geophysical Exploration
• /
• v.23 no.3
• /
• pp.208-214
• /
• 2020

In this study, we have developed a drone magnetic exploration system (proto-type) using a fluxgate magnetic sensor. Hardware of the system consists of a fluxgate magnetometer, an inertial measurement unit (IMU), a GPS, and a communication module. And we have developed monitoring software, which enables it to transmit the measured data to the ground control system (GCS) in real time. The measured magnetic data are finally saved as 1 Hz data after passing through a notch filter and a band-pass filter. For verification of this system, a preliminary test was conducted to check the magnetic responses of a magnetic object first, then the field test was carried out in two iron mines. We tested the developed system on the field test in Pocheon, Gyeonggi and Jeongseon, Gangwon. The magnetic data from the developed drone system was very similar to those from unmanned airship system developed by Korea Institute of Geoscience and Mineral Resources (KIGAM). As a result, preliminary experiment and field test have demonstrated that this system is applicable for outdoor aeromagnetic exploration. It requires more studies to improve filter function and instrument performance to minimize noise in the future.