• Journal of Oral Medicine and Pain
• /
• v.30 no.4
• /
• pp.447-455
• /
• 2005

The purpose of this study was to examine the effect of Nd:YAG laser irradiation for sensory nerve conduction change. Nd:YAG laser was irradiated to mental region for 5 minutes with the parameters that 10 Hz and 20 Hz of 100 mJ/pulse. Target size of irradiation was 30 mm diameter of circle and target-tip distance was about 10 mm. Therefore, the power density were 212 $mW/cm^2$ and 424 $mW/cm^2$. Sensory nerve conduction was evaluated with $Neurometer^{\circled}$ CPT/C before and after Nd:YAG laser irradiation. As an outcomes, the current perception threshold(CPT) and pain tolerance threshold(PTT) were obtained. We made a comparison of these two values and the results were as follows. 1. There was no significant difference in CPT at 1W, 10 Hz and 2 W, 20 Hz Nd:YAG laser irradiation. 2. There was no significant difference in PTT at 10 Hz, 20 Hz of 100 mJ/pulse Nd:YAG laser. 3. There were no significant differences in CPT and PTT between 1 W, 10 Hz group and 2 W, 20 Hz group. Therefore, We can make a conclusion that Nd:YAG laser irradiation to mental region have no effect on mental nerve conduction in our study model.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.3
• /
• pp.285-294
• /
• 2020

This study investigated the use of Ground Penetrating Radar (GPR) over a two-decade period on public roads, focusing on the electromagnetic characteristics of the pavement dielectrics and attenuation. From the results, a typical range of characteristic value, influencing factors, and a correction method were suggested. The typical dielectrics of asphalt pavements were 4-7, as measured by an air-coupled 1 GHz GPR antenna. The dielectrics of concrete pavements were very large in the early age, but were drastically reduced with ageing. Ten years on, collection was in the range of 6-12. The dielectrics were proportional to the relative humidity (R.H.) of the atmosphere. The effects were reduced to one eighth with an overlay. Attenuation generally increased with thickness of the road layer, and also increased where there was damage. The GPR results could also vary depending on the weather conditions as well as on the characteristics of the GPR equipment, even at the same frequency. Therefore, GPR surveys should be performed on road surfaces without debris on a single, fine day. The reliability of the GPR analysis could be improved by cores and equipment calibration with other non-destructive test surveys.

• The Journal of Engineering Geology
• /
• v.25 no.2
• /
• pp.227-235
• /
• 2015

In recent years, owing to the frequent occurrence of natural disasters, the inspection and maintenance of structures have become increasingly important on a national scale. However, because most structural inspections are carried out manually, and due to the lack of objectivity in data acquisition, quantitative data are not always available. As a result, researchers are seeking ways to collect and standardize survey data using terrestrial laser scanning, thereby bypassing the limitations associated with visual investigations. However, field data acquired using a laser scanner have been required to measure changes in structure geometry resulting from passive deterioration. In this study, we demonstrate that it is possible to identify the processes of structural deterioration (e.g., efflorescence, leakage, delamination) using intensity data from terrestrial laser scanning. Additionally, we confirm the viability of automated classification of alteration type and objectification of the polygon area by establishing intensity characteristics. Finally, we show that our method is effective for structural inspection and maintenance.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.1
• /
• pp.131-135
• /
• 2008

Purpose: To measure and quantify the factors of intraocular pressure (IOP) variation for normal Korean youth. Methods: The IOP of normal youth 805 persons (male: 367, female: 438) were measured as a function of time and quantity for fixation, reclining posture, hard blinking, drinking water, drinking hard liquor, tobacco and coffee by using non-contact tonometer (AT555, Reichert Co.). In the case of fixation, reclining posture and hard blinking, the intraocular pressure of right and left eye were measured for 6 males and 6 females every 10 minutes during 30 minute. In the case of water, liquor, tobacco and coffee, the measurement for 4 or 5 groups (6 persons/ group) having similar IOP were done for the IOP variation of right eye. Results: The mean IOP was 15.2 mmHg for males and 15.8 mmHg for females (slightly higher than male's), respectively and the 99% of those were in the range of the normal IOP. The measured IOP was increased by fixation, reclining posture and hard blinking with males and females. The gradient of increasing slope was 0.15/0.13/0.07/0.08, 0.09/0.08/0.08/0.08 and 0.19/0.08/0.26/0.31, respectively. The IOP variation was elevated by drinking water (especially in the case of 1000 ml) and lowered in proportion to the amount of drinking by hard liquor. Cigarette smoking was associated with rise in intra ocular pressure, but was not shown a definite relation. And coffee had virtually no effect. Conclusions: Fixation, reclining posture, hard blinking and Tobacco caused a transient increase in IOP, but alcohol elicited a slight reduction in IOP overall.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6B
• /
• pp.561-571
• /
• 2006

RFID technology, as one contact-less identification technology with using electronic tag, is the field where its multiple researches have been studied. Especially, in the field of supply chain management, when it is necessary to identify a lot of objects by real-time, performance of anti-collision algorithm for multiple tag identification has an effect on performance of entire system. GEN2 is global, open, interoperability protocol for UHF RFID system, the active researches and developments are processed about it. In this paper, we introduce an anti-collision algorithm based on Slotted-ALOHA for GEN2 protocol, focus on estimating number of tags and setting number of slots and review the previous works. We propose new scheme that can estimate number of tags efficiently, and define system efficiency newly when it's used in setting number of slots. We also present result of compare and analysis with previous scheme through simulation. The proposed scheme of estimating number of tags is easy to implement, number of tags which is less than 4 times of number of slots can estimate tags efficiently, we also proved that identification efficiency based on weighted-slot distinguished with definition of previous slot efficiency can improve system efficiency.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1994.10b
• /
• pp.15-15
• /
• 1994

M MA ODS 합금의 보다 폭넓용 실용확훌 위해 크게 요구되고 있는 적정 접합기술 개발의 한 방안￡로, 마찰압접(Friction Welding) 방법의 가능성옳 조사하기 위하여 마찰압력과 시간, 마 찰 후 접촉압력(Upset Pressure) 풍을 다양하게 변화시켜 접합체톨 제조한 후, 접합체 강도에 대한 인장시험과 접합계연의 결합 및 미세구조에 대한 현미경 관찰, EDS에 의한 원소분석, 접 합이옴부의 경도분포와 파단면 분석 풍율 행하였다. 실험에 사용된 모재는 기계적 합금법으로 제조된 Inca사의 Ni기 MA 754 합금이었으며, 직경 l 10 mm, 길이 50 mm로 가공한 후, 아세통￡로 초음파 세척하여 접합에 사용하였다. 접합온 브 레이크식 마찰압접기틀 사용하여 행하였으며, 회전시험편의 회전수는 2400 rpm이었A며, 다른 한쪽의 고정시험편과의 마찰압력 및 마찰시간온 각각 50 - 500 MPa과 1-5초로, 또한 업셋압 력도 50 - 600 MPa로 변화시켰다. 이때 업셋압력은 모든 시편에 대해 일정하게 6초동안 가하 였다. 얻어진 접합체는 각 압접조건 당 2개 이상의 접합시험편에 대해 상온 인장강도톨 측정하 였으며, 파단이 일어난 위치를 확인한 후 파면에 대한 분석율 주사전자현미경(SEM)과 에너지 분산형 분광분석기mDS)릎 사용하여 행하였다. 컵합이옴부의 첩합성올 확인하기 위하여, 접합 체를 접합변에 수직으로 절단, 연마한 후 광학현미경과 SEM, EDS 퉁으로 관찰, 분석하여 접 합부의 형상과 결합형성 여부, 접합계면의 미세조직 퉁옳 조사하였다. 또한 마찰압접에 따론 모재와 접합계연부의 경도분포훌 접합이옴부로부터 모재쪽으로 일정 간격율 두어 마이크로 비 커스 경도기로 측정, 조사하였다. 이상의 설험 결과, 다옴과 같온 결론옳 얻었다. ( (1) 접합체 강도가 모채 강도의 95% 이상이 되는 양호한 렵합체흩 얻기 위한 마찰압력 조건 온, 2400 rpm의 회전속도와 6초의 업셋압력 유지시간에서 마찰압력과 업셋압력, 그리고 마찰시 간이 각각 400 MPa 이상과 500 MPa 이상,2초입율 확인하였다. ( (2) 컵합이옴부의 관찰 결과, 모든 마찰압접 조건에서 컵합이옴부는, 기폰 모재의 texture 조직 을 유지하고 있는 모재부 영역(영역 ill)과 첩합계면부에 인접하여 업셋압력이 주어질 때 단조 효과에 의해 계연 외부로 metal flow가 일어나면서 형성된 영역 II, 매우 미세한 결정립으로 구성된 중앙부의 영역 1 로 이투어져 있옴융 확인하였다. ( (3) 최적접합조건이 충족되지 않온 경우, 접합부의 영역 I 에서 관찰된 void와 균열, 불균일한 접합계면 통의 접합결함에 Al과 Y. Ti 퉁￡로 구성된 산화물률이 용집되어 있옴을 확인하였 다-( (4) 접합체의 파단 양상온 크게 접합부 파단과 모재부 파단, 이률의 혼합형 파단i로 나눌수 있었다. 모재부 파단의 경우, 파단면이 매끄럽고 파변상의 결정립도 매우 미세하였으며, 산확물 의 용집도 찾아보기 어려웠 나, 접합부 파단의 경우에는 파변의 굴곡이 비교척 심하고 연성 입계파괴의 형태를 보였￡며, 결정립도 모채부 파단의 경우에 비해 조대하였다. 조대하였다.

• Ecology and Resilient Infrastructure
• /
• v.8 no.1
• /
• pp.22-31
• /
• 2021

Surface image velocimetry (SIV) is a noncontact velocimetry technique based on images. Recently, studies have been conducted on surface velocity measurements using drones to measure a wide range of velocities and discharges. However, when measuring the surface velocity using a drone, reference points must be included in the image for image correction and the calculation of the ground sample distance, which limits the flight altitude and shooting area of the drone. A technique for calculating the surface velocity that does not require reference points must be developed to maximize spatial freedom, which is the advantage of velocity measurements using drone images. In this study, a technique for calculating the surface velocity that uses only the drone position and the specifications of the drone-mounted camera, without reference points, was developed. To verify the developed surface velocity calculation technique, surface velocities were calculated at the Andong River Experiment Center and then measured with a FlowTracker. The surface velocities measured by conventional SIV using reference points and those calculated by the developed SIV method without reference points were compared. The results confirmed an average difference of approximately 4.70% from the velocity obtained by the conventional SIV and approximately 4.60% from the velocity measured by FlowTracker. The proposed technique can accurately measure the surface velocity using a drone regardless of the flight altitude, shooting area, and analysis area.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.6
• /
• pp.589-604
• /
• 2021

Waterjets for rocks have various advantages of the non-contact and eco-friendly excavation using only water and abrasive. To overcome the problems (e.g., dust and noise occurrence) of the conventional drilling methods, waterjet excavation methods are broadly used. It is advantageous to operate a couple of nozzles in order to increase the waterjet excavation efficiency. When multiple nozzles are used, it is essential to analyze the excavation performance and shape according to the nozzle operation method. In this study, nozzle angle, horizontal distance between nozzles, and standoff distance were defined as nozzle operating parameters and the excavation performance and shape were analyzed. As a result of the experiment, when the nozzle angle and standoff distance are increased, the excavation depth is decreased and the effective depth tends to be increased. In addition, based on the experimental results, the excavation shape criteria required for nozzle insertion were proposed and optimal nozzle operating parameters were derived according to the criteria. This study result is expected to be used as useful basic research in the future development of multiple waterjet nozzles for rock drilling.

• Smart Media Journal
• /
• v.13 no.6
• /
• pp.54-61
• /
• 2024

Recently, due to the increase in domestic and international online e-commerce platforms and the increase in container traffic at domestic ports, the operating ratio of large trucks has increased, and the number of truck fires is continuously increasing. In particular, spontaneous combustion is the most common cause of truck fires. Various academic approaches have been attempted to prevent truck fires, but due to the lack of research on the spontaneous tire ignition phenomenon that occurs during braking, this research directly designed and manufactured an experimental device to establish an environment similar to the braking system of a truck. A non-contact temperature sensor was installed on the brake device of the experimental device to collect temperature data generated from the brake device. Based on the data collected from the temperature sensor of the brake device and the temperature sensor on the tire surface, the ARIMA model among the time series prediction models was used to Appropriate parameters were selected to suit the temperature change trend, and as a result of comparing and analyzing the measured and predicted data, an accuracy of over 90% was obtained. Based on this, a plan was proposed to reduce the rate of fires in trucks by providing real-time warnings and support for truck drivers to respond to overheating phenomena occurring in the braking system.

• Korean Journal of Materials Research
• /
• v.2 no.3
• /
• pp.228-238
• /
• 1992

An investigation on the step-coverage of PECVD and $O_3$ ThCVD oxides was undertaken to implement into the void-free inter metal dielectric planarization using multi-chamber system for the submicron double level metallization. At various initial aspect ratios the instantaneous aspect ratios were measured through modelling and experiment by depositing the oxides up to $0.9{\mu}m$ in thickness in order to monitor the onset of void formation. The modelling was found to be in a good agreement with the observed instantaneous aspect ratio of TEOS-based PECVD oxide whose re-entrant angle was less than $5^{\circ}$. It is demonstrated that either keeping the instantaneous aspect ratio of PECVD oxide as a first layer less than a factor of 0.8 or employing Ar sputter etch to create sloped oxide edge ensures the void-free planarization after$O_3$ ThCVD oxide deposition whose step-coverage is superior to PECVD oxide. It has been observed that $O_3$ ThCVD oxide etchback scheme has shown higher yield of via contact chain than non etchback process, with resistance per via contact of $0.1~0.3{\Omega}/{\mu}m^2$.