• The Research Journal of the Costume Culture
• /
• v.31 no.6
• /
• pp.738-755
• /
• 2023

The purpose of this study is to provide basic data for the production of jackets with high fit by comparing and analyzing the adhesive and non-adhesive production methods of men's jackets. An analysis of the manufacturing method showcased differences between the adhesive and non-adhesive manufacturing methods in the cutting and wick attachment method, the shape and attachment method of the chest reinforcing wick, the sleeve attachment method, and the shoulder pad and sleeve reinforcing cloth attachment method. In evaluating the outfit, the overall fit of the shoulder, the fit of the chest, and the fit of the armpit were found to be high in the non-adhesive production method. In evaluating appearance evaluation, the front shoulder, chest, and sleeve overall appearance showed a high non-adhesive production method. Therefore, in order to increase the wearability of the shoulder pad and the the attachment method of the upper sleeve reinforcing cloth, the non-adhesive production method should be used, and in order to increase the overall wearability and armpit wear of the chest, the difference in the attachment method, and the reinforcement method of the armhole should be used. In addition, to increase the appearance of the jacket, non-adhesive production methods such as differences in wick attachment methods, shoulder pads, sleeve reinforcing cloth, and sleeve attachment methods should be used.

• The korean journal of orthodontics
• /
• v.34 no.4 s.105
• /
• pp.333-342
• /
• 2004

The purpose of this study was to evaluate the clinical effectiveness of a plasma arc light and light emitting diode (LED), compared with shear bond strength and the failure pattern of brackets bonded with visible light in direct bonding. Brackets were bonded with Transbond XT to 60 human premolars embedded in the resin blocks according to different light-curing methods. Then, the shear bond strength of each group was measured using a universal testing machine (Instron) and the adhesive failure pattern after debonding was visually examined by light microscope. The results were as follows: 1. The shear bond strength showed no significant difference between the visible light and light emitting diode, but the plasma arc light exhibited a significantly lower shear bond strength compared with the visible light and light emitting diode. 2. In the visible light and light emitting diode, adhesive failure patterns were similar. Bond failure occurred more frequently at the enamel-adhesive interface. 3. The bonding failure of brackets bonded with plasma arc light occurred more frequently at the bracket-adhesive interface. The results of this study suggest that plasma arc light, light emitting diode and visible light are all clinically useful in the direct bonding of orthodontic brackets.

• Resources Recycling
• /
• v.27 no.2
• /
• pp.3-10
• /
• 2018

In this paper, Proposed bonding mechanism that can separate sole and upper for recycle and reuse of parts. It was confirmed that the PVC film with better physical properties than the existing parts was inserted between the sole and the upper. It was confirmed that the separation of the desired form can be induced. As a result of checking the performance of the proposed mechanism, it is confirmed that intentional separation is possible and the separated sole and upper can be recycled or reused.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.151-151
• /
• 1999

금속-산화막-반도체(MOS) 소자를 이용하는 집적회로의 발전은 게이트 금속의 규격 감소를 필요로 한다. 규격감소에 따른 저항 증가가 중요한 문제점으로 대두되었으며, 그동안 여러 연구자들에 의하여 금속 게이트에 관련된 연구가 진행되어 왔다. 특히 저항이 낮으며 녹는점이 매우 높은 내화성금속(refractory metal)인 텅스텐(tungsten, W)이 차세대 MOS 소자의 유력한 대체 게이트 금속으로 제안되었다. 텅스텐은 스퍼터링(sputtering)과 화학기상 증착(CVD) 방식을 이용하여 성장시킬 수 있다. 스퍼터링에 의한 텅스텐 증착은 산화막과의 접착성은 우수한 반면에 증착과정 동안에 게이트 산화막(SiO2)에 손상을 주어 게이트 산화막의 특성을 열화시킬 수 있다. 반면, 화학기상 증차에 의한 텅스텐 성장은 스퍼터링보다 증착막의 저항이 상대적으로 낮으나 산화막과의 접착성이 좋지 않은 문제를 해결하여야 한다. 본 연구에서는 감압 화학기상 증착(LPCVD)방식을 이용하여 텅스텐 게이트 금속을 100~150$\AA$ 두께의 게이트 산화막(SiO2 또는 N2O 질화막)위에 증착하여 물리 및 전기적 특성을 분석하였다. 물리적 분석을 위하여 XRD, SEM 및 저항등이 증착 조건에 따라서 측정되었으며, 텅스텐 게이트로 구성된 MOS 캐패시터를 제작하여 절연 파괴 강도, 전하 포획 메커니즘 등과 같은 전기적 특성 분석을 실시하였다. 특히 텅스텐의 접착성을 증착조건의 변화에 따라서 분석하였다. 텅스텐 박막의 SiO2와의 접착성은 스카치 테이프 테스트를 실시하여 조사되었고, 증착시의 기판의 온도에 민감하게 반응하는 것을 알 수 있었다. 또한, 40$0^{\circ}C$ 이상에서 안정한 것을 볼 수 있었다. 텅스텐 박막은 $\alpha$ 및 $\beta$-W 구조를 가질 수 있으나 본 연구에서 성장된 텅스텐은 $\alpha$-W 구조를 가지는 것을 XRD 측정으로 확인하였다. 성장된 텅스텐 박막의 저항은 구조에 따라서 변화되는 것으로 알려져 있다. 증착조건에 따른 저항의 변화는 SiH4 대 WF6의 가스비, 증착온도에 따라서 변화하였다. 특히 온도가 40$0^{\circ}C$ 이상, SiH4/WF6의 비가 0.2일 경우 텅스텐을 증착시킨 후에 열처리를 거치지 않은 경우에도 기존에 발표된 저항률인 10$\mu$$\Omega$.cm 대의 값을 얻을 수 있었다. 본 연구를 통하여 산화막과의 접착성 문제를 해결하고 낮은 저항을 얻을 수 있었으나, 텅스텐 박막의 성장과정에 의한 게이트 산화막의 열화는 심각학 문제를 야기하였다. 즉, LPCVD 과정에서 발생한 불소 또는 불소 화합물이 게이트의 산화막에 결함을 발생시킴을 확인하였다. 향후, 불소에 의한 게이트 산화막의 열화를 최소화시킬 수 있는 공정 조건의 최저고하 또는 대체게이트 산화막이 적용될 경우, 개발된 연구 결과를 산업체로 이전할 수 있는 가능성이 높을 것을 기대된다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.3
• /
• pp.212-219
• /
• 2015

This study focuses evaluating the efficiency and performance evaluation of composite type sheet-membrane waterproofing method that utilizes a separation behavior inducement system designed to resolve the chronic problems of disintegration and damage of overlap areas of waterproofing layers. As the result of the test, the tensile strength value was at 13.8N/mm and elongation rate at 587% for the separation behavior inducement type specimen, and the compared specimens had 14.2N/mm for tensile strength and 335% for elongation rate. For the separation behavior adhesion method specimen, when tensile stress or displacement occurred, the Zero-Span tension occurrence did not follow, which resulted in that the bottom sheet layer and the top membrane layer did not simultaneously becoming damaged. When undergoing the top and bottom layers were separated through separation behavior due to lack of flexibility, the bottom layer began to damage at the primary stage, and with the allowed boundary the upper membrane layer began to display flexibility and showed continuous displaced resulting in secondary phase damaging.

• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.406-413
• /
• 2001

Up to this day, reinforced spun concrete pipes have been widely used as drain pipes. However, many reinforced spun concrete pipes are exposed to the deteriorated environment such as freezing-thawing damage and chemical attack by the growth of a sulfur-oxidizing bacterium isolated from corroded concrete. The purpose of this study is to evaluate the effects of lining by polymer-modified mortar using polymer dispersions as cement modifier on the development in durability of reinforced spun concrete pipe. The polymer-modified mortars were prepared with various polymer types and polymer-cement ratios, and tested for compressive and flexural strengths, acid, freezing-thawing, and heat resistances. And then, the reinforced spun concrete pipe product lined by polymer-modified mortars was tested for adhesion in tension and surface conditions according to curing temperatures in the field. From the test results, it is apparent that the polymer-modified mortars have good mechanical properties and durability as a lining material. In practice, all polymers can be used as lining the materials for reinforced spun concrete pipe, and types of polymer, and polymer-cement ratio and curing conditions are controlled for a good lining product.

• Journal of Sensor Science and Technology
• /
• v.11 no.3
• /
• pp.171-182
• /
• 2002

The differential electromagnetic transducer for IME(implantable middle ear) system, which have two small permanent magnets glued with the same pole facing each other in the coil, has high vibration efficiency and does not influenced by external magnetic field. In this paper, using finite element method, highly efficient structure of the transducer was proposed and vibration force of the transducer was calculated by electromagnetic theory. And the necessary vibration force of transducer to transmit the sound signal to inner ear when the transducer is attached at stapes was calculated and the design parameters of the transducer were investigated. Using the parameters, the differential electromagnetic transducer was manufactured in small size to implant in confined human middle ear. And it was examined by unloaded and loaded vibration experiment using temporal bone sampled from cadaver.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.12
• /
• pp.79-88
• /
• 2011

Adfreeze bond strength develops upon freezing of pore water within soil and at foundation surface. It has been reported that various factors like temperature, soil type, and pile surface roughness affect adfreeze bond strength. Especially, pile surface roughness has been considered as a primary factor to design pile foundation in frozen ground. It has usually been estimated with fixed correction factors for pile materials. However, even if the pile foundation material is the same, the surface roughness could vary depending on the production circumstances. In this study, laboratory test was carried out to quantitatively analyze the effects of surface roughness on the adfreeze bond strength, and fractal dimension was used as a measure for surface roughness. Test results showed that adfreeze bond strength increased with decreasing temperature, increasing vertical stress and surface roughness. The adfreeze bond strength varies sensitively with surface roughness in the early freezing section of $-2^{\circ}C$, but its sensitivity decreased in the temperature ranging between $-2^{\circ}C$ to $-5^{\circ}C$. The results conclude that the roughness highly affects the frictional resistance of pile surface in frozen ground; however, the roughness does not affect considerably when the temperature drops below about $-2^{\circ}C$.

• The korean journal of orthodontics
• /
• v.29 no.4 s.75
• /
• pp.445-456
• /
• 1999

As a result of increased education and communication, the field of orthodontics has recently been expanded to include a greater number of adult treatment procedures. With this increased demand for adult orthodontic treatment, a problem that frequently arises is the placement of appliances on teeth restored with porcelain. But conventional acid-etching is ineffective in the preparation of porcelain surface for mechanical retention of orthodontic attachments. Also, it is possible to damage on porcelain. The purpose of this study was to evaluate the effect of composite bonding materials and the porcelain surface treatment methods on shear bond strength, and to observe the porcelain fracture rates. To accomplish this purpose, this study was carried out with feldsphatic porcelain, Ceram II. Porcelain surface treatment methods were divided into intact glazed porcelain which had not treatment and surface roughening. Surface roughening by etching with Hydroluoric acid(HF), sandblasting with Microetcher II and compound treatment with etching and sandblasting. Bonding materials were Ortho-two and Transbond. All porcelain specimens were applicated with porcelain primer. 1. In comparision according to porcelain surface treatment, surface roughening groups by HF etching and sandblasting had higher shear bond than intact group. No significant difference was found in Transbond group. 2. Ortho-two group had the higher shear bond strength than that of Transbond group in B:.u etching and sandblasting. 3. E(Transbond. Intact)group had the lowest shear bond strength in all experimental group. The bond strength was higher than clinically successful bond strength. 4. Non-treated group had very higher porcelain rates than treated group. 5. This study indicates that porcelain surface-roughening may not be necessary to attachment of orthodontic brackets to porcelain surfaces.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.7-14
• /
• 2010

This paper describes the effects of kinetic parameters such as attaching speed, attaching time, and dettaching speed on printing property of electrodes which were fabricated by micro-contact printing with Ag ink. In inking process the attaching speed was preferable to be less than 1 mm/s, attaching time as short as possible, and detaching speed larger than 1000 mm/s in order to obtain the transfer ratio of ink larger than 98%. Meanwhile in printing process the parameters were totally opposite to the results of inking process; attaching speed larger than 100 mm/s, attaching time larger than 30 sec, and detaching speed less than 1 mm/s for the best results. With the parameters we could obtain the micro-contact printed electrodes with the minimum line width of $30\;{\mu}m$, thickness of 300~500 nm, roughness less than 50 nm, and resistivity of about $15{\sim}16{\mu\Omega\cdot}cm$.