• Korean Journal of Metals and Materials
• /
• v.56 no.12
• /
• pp.915-920
• /
• 2018

With the development of modern microelectronics technologies, the power density of electronic devices is rapidly increasing, due to the miniaturization or integration of device elements which operate at high frequency, high power conditions. Resulting thermal problems are known to cause power leakage, device failure and deteriorated performance. To relieve heat accumulation at the interface between chips and heat sinks, thermal interface materials (TIMs) must provide efficient heat transport in the through-plane direction. We report on the enhanced thermal conduction of $Al_2O_3-based$ polymer composites, fabricated by the surface wetting and texturing of thermally conductive hexagonal boron nitride(h-BN) nanoplatelets with large anisotropy in morphology and physical properties. The thermally conductive polymer composites were prepared with hybrid fillers of $Al_2O_3$ macro beads and surface modified h-BN nanoplatelets. Hexagonal boron nitride (h-BN) has high thermal conductivity and is one of the most suitable materials for thermally conductive polymer composites, which protect electronic devices by efficient heat dissipation. In this study, we synthesized hexagonal boron nitride nanoparticles by the pyrolysis of cost effective precursors, boric acid and melamine. Through pyrolysis at $900^{\circ}C$ and subsequent annealing at $1500^{\circ}C$, hexagonal boron nitride nanoparticles with diameters of ca. 50nm were synthesized. We demonstrate that the addition of a small amount of calcium fluoride ($CaF_2$) during the preparation of the melamine borate adduct significantly enhanced the crystallinity of the h-BN and assisted the growth of nanoplatelets up to 100nm in diameters. The addition of a small amount of h-BN enhanced the thermal conductivity of the $Al_2O_3-based$ polymer composites, from 1.45W/mK to 2.33 W/mK.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.4
• /
• pp.434-442
• /
• 2022

Highly toxic chemical warfare agents(CWA) could be used in chemical warfare and terrorism. The protection of skin is crucial for civilians and soldiers, because the primary routes of exposure to CWA are inhalation and skin absorption. Thus, topical skin protectants(TSP) have been studied and developed in many countries to complement protective equipments. In this study, in-vitro test procedure was optimized and established using a flow-through diffusion cell system containing excised hairless mouse skin in an attempt to assess the effectiveness of various TSP formulations against nerve agent simulants. In addition, the test results on the formulations including the ingredients used in SERPACWA(Skin Exposure Reduction Paste Against Chemical Warfare Agent) and IB-1(TSP of Israel) were included, indicating that the formulations with perfluorinated compounds were more effective than the glycerin-based formulations.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.55 no.5
• /
• pp.514-523
• /
• 2022

Concentrations of perfluoroalkyl substances (PFASs) were measured in seawater, sediment, and biota collected from Gunsan coast, Korea to investigate their occurrence, distribution, and risk of exposure to humans through seafood consumption. The total concentrations of PFASs in seawater, sediment, and biota ranged from 5.97 to 74.9 ng/L, 0.01 to 13.3 ng/g dry weight, and 0.02 to 5.73 ng/g wet weight, respectively. Predominant PFAS compounds differed across matrices, indicating that the distribution of PFASs in multiple environmental samples is governed by their carbon-chain length. The concentrations of PFASs in seawater were significantly negatively correlated with salinity (P<0.01), suggesting terrestrial input (including land-used PFASs) as the major source of PFAS contamination in coastal environments. The estimated daily intakes (EDIs) of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) through seafood consumption were 0.05 and 0.06 ng/kg body weight/day, respectively. The EDIs of PFOA and PFOS measured in this study were lower those the proposed by the United States Environmental Protection Agency and Canada guidelines, indicating limited health risk for Korean population from PFASs through consumption of seafood from Gunsan coastal environment.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.31 no.2
• /
• pp.5-18
• /
• 2023

As a result of the survey on the emission status of fluorine-based chemicals in Korea, 13 kinds of substances, including hydrogen fluoride (91%) and perfluorocarbons (5%), were emitted in workplaces. By regional groups, about 98% was emitted in the Gyeongbuk, Gyeonggi and Chungcheong regions, and about 98% in three sectors of industry related to manufacture of electronic parts, chemicals and non-metallic mineral products. The detection status of PFOS and PFOA in domestic main rivers was continuously detected in the Nakdong River, the Geum River and the Anseong Stream estuary with high fluorine-related chemical emissions, and four sites of PFOS and two sites of PFOA were detected for the first time in 2021. PFOS and PFOA were continuously detected in relatively high concentrations in the rivers where there were many semiconductor and display related sectors of industry.

• SUVANNABHUMI
• /
• v.1 no.2
• /
• pp.1-20
• /
• 2009

This research tries to review the history and concepts of Thai temple mural painting. According to the research results, the history of Thai mural painting dates back to the late 14th century when Wat Chedi Chet Taeo in Si Satchanalai was built. The Sinhalese elements embedded in the Sukhothai murals are also found in the Ayuthayan stupa murals made in the early 15th century. The mid 18th century's Burmese invasion into Ayuthaya destroyed most of Buddhist temples in the Kingdom of Ayuthaya and as a result, Buddhist murals of the late Ayuthayan age are hardly found except for some temple murals located outside of the capital. The late Ayuthayan murals are much different from the early Ayuthayan murals in that they are narrative in depicting Jataka and the life of Lord Buddha. This classical mural painting culminated in the age of Rama III of Bangkok Dynasty. His successor Rama IV undertook westernized reforms which influenced the area of traditional mural painting. Consequently, new western style Buddhist mural paintings were produced while themes of mural painting were enlarged to the other subjects such as historical recording of royal and social events. This trend continued in the age of Rama V but the development of Thai Buddhist mural painting discontinued after the death of Rama V due to the rapid westernization and decrease of illiteracy. The existing Buddhist murals produced on or before the reign of Rama V are deteriorating and disappearing. The reasons for this are partly because of Thailand's humid climate. However, some social backgrounds such as the lack of concern for preserving old Buddhist murals can not be disregarded. Considering the substantial value of Thai Buddhist murals as a cultural resource in Thai society, it is very urgent to establish appropriate conservation policy for them.

• Journal of Sensor Science and Technology
• /
• v.32 no.5
• /
• pp.328-333
• /
• 2023

This study experimentally verified the etch rate of the SiO₂ sacrificial layer etching process with a single etch hole using vapor-phase hydrogen fluoride (VHF) etching. To fabricate small-sized polysilicon etch holes, both circular and triangular pattern masks were employed. Etch holes were fabricated in the polysilicon thin film on the SiO₂ sacrificial layer, and VHF etching was performed to release the polysilicon thin film. The lateral etch rate was measured for varying etch hole sizes and sacrificial layer thicknesses. Based on the measured results, we obtained an approximate equation for the etch rate as a function of the etch hole size and sacrificial layer thickness. The etch rates obtained in this study can be utilized to minimize structural damage caused by incomplete or excessive etching in sacrificial layer processes. In addition, the results of this study provide insights for optimizing sacrificial layer etching and properly designing the size and spacing of the etch holes. In the future, further research will be conducted to explore the formation of structures using chemical vapor deposition (CVD) processes to simultaneously seal etch hole and prevent adhesion owing to polysilicon film vibration.

• The korean journal of orthodontics
• /
• v.33 no.2 s.97
• /
• pp.113-120
• /
• 2003

The aim of this study was to evaluate the effect a chewable tablet containing sodium fluoride and xylitol (DenPo, Hamizzle, Bucheon, Kyungki) on the oral hygiene state in the orthodontic patients.'rho subjects consisted of 30 adult orthodontic patients, who have worn the fixed orthodontic appliance at least 6 months. They were instructed to use the tablet forth a day, Gingival index (GI), plaque index (PI), and sulcus bleeding index (SBI) of upper and lower anterior and posterior regions were measured before using the tablet (T0), 2 weeks after using the tablet (T1), and 4 weeks after using the tablet (T2). The data were analyzed with Wilcoxon signed ranks tests. The results were as follows ; 1 PI was decreased significantly in the T1 and T2 stage compared with T0 stage in the both anterior and posterior regions (p<0.05). Although PI was decreased in the T2 stare compared with T1, there was not statistical significance (p>0.05). 2. GI and SBI showed similar results compared with PI. In the T1 and T2 stage, there was statistically significant decrease in the GI and SBI (p<0.05), This study showed that the DenPo tablet could be used as an adjunct to improve oral hygiene in the orthodontic patients. The decrease of the indices nay suggest that DenPo tablet could be effective in the plaque removal and prevention of gngival inflammation in the orthodontic patients.

• Journal of dental hygiene science
• /
• v.6 no.4
• /
• pp.303-307
• /
• 2006

The objective of this study was to evaluate the effects of the topical application of fluoride by iontophoresis on the fluoride concentration in the dental enamel. Eighty-eight healthy teeth were extracted from orthodontic patients and divided into three experimental groups at 0.2 mA and 0.5 mA current and a control group. Each experimental group was further divided into three subgroups according to the application time (1, 3, and 5 min). Five to six teeth were assigned to each subgroup. Inotophoresis was performed using a 2% sodium fluoride solution and each tooth was sliced into a $3{\times}3mm$ specimen on enamel. The fluoride concentration in the enamel was measured using X-ray photoelectron spectroscopy. It was used to estimate the atomic ratio of fluoride on the enamel surface on selected samples. The specimen was observed via scanning electron microscopy as well. This finding was confirmed by the result that the fluoride ratios estimated by x-ray photoelectron spectroscopy was 2.71%, 2.87% and 3.80% after fluoride iontophoresis had been performed using a 2% sodium fluoride solution at 0.5 mA for 1, 3 and 5 min, respectively. In comparison, the fluoride ratio was 0.49% in the control group. As the current became higher and the time lapsed, the formation of irregular particles was strengthened on the enamel surface. Afterwards, the enamel surface was dissolved and new matrix was formed on the enamel. Fluorapatite was observed on the enamel after fluoride iontophoresis was performed at 0.5 mA for 5 min. The fluoride concentration tended to increase with increasing duration of iontophoresis. The study findings indicated that under proper conditions, fluoride iontophoresis has a positive effect in increasing the fluoride concentration in dental enamel.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.1
• /
• pp.61-66
• /
• 2012

Chemical Mechanical Planarization (CMP) is a polishing process used in the microelectronic fabrication industries to achieve a globally planar wafer surface for the manufacturing of integrated circuits. Pad conditioning plays an important role in the CMP process to maintain a material removal rate (MRR) and its uniformity. For metal CMP process, highly acidic slurry containing strong oxidizer is being used. It would affect the conditioner surface which normally made of metal such as Nickel and its alloy. If conditioner surface is corroded, diamonds on the conditioner surface would be fallen out from the surface. Because of this phenomenon, not only life time of conditioners is decreased, but also more scratches are generated. To protect the conditioners from corrosion, thin organic film deposition on the metal surface is suggested without requiring current conditioner manufacturing process. To prepare the anti-corrosion film on metal conditioner surface, vapor SAM (self-assembled monolayer) and FC (Fluorocarbon) -CVD (SRN-504, Sorona, Korea) films were prepared on both nickel and nickel alloy surfaces. Vapor SAM method was used for SAM deposition using both Dodecanethiol (DT) and Perfluoroctyltrichloro silane (FOTS). FC films were prepared in different thickness of 10 nm, 50 nm and 100 nm on conditioner surfaces. Electrochemical analysis such as potentiodynamic polarization and impedance, and contact angle measurements were carried out to evaluate the coating characteristics. Impedance data was analyzed by an electrical equivalent circuit model. The observed contact angle is higher than 90o after thin film deposition, which confirms that the coatings deposited on the surfaces are densely packed. The results of potentiodynamic polarization and the impedance show that modified surfaces have better performance than bare metal surfaces which could be applied to increase the life time and reliability of conditioner during W CMP.

• Journal of Yeungnam Medical Science
• /
• v.7 no.2
• /
• pp.67-77
• /
• 1990

This study was intended to analyse the relation between the psychic traumatic experience and the psychological health of the aged. The authors carried out this study by means of the combined anxiety-depression scale(CADS) and the preadolescence traumatic experience scale(PTES) with 278 aged men and women residing in Taegu from September to October 1988. The results were as follows : 1. Based on the scores avaluated by CADS, the scores of the both groups showed that comparative group was accounted for $40.15{\pm}6.19$, while the experimental group for $57.75{\pm}6.37$, which showed significantly higher score in the experimental group(p<0.001). 2. The experimental group showed significantly higher early experience score than the comparative group in the dietary difficulty, alcoholism among family members, disunion between husband and wife, trouble between mother and children, early mother loss, parent's indifference and unwanted birth(p<0.001). 3. The experimental group showed higher early experience score than the comparative group by sex, age, marital status and grown location(p<0.001). 4. When the subjects were included in the unemployed and in the middle or low classes and their parents were engaged in agriculture and commercial business and believing in buddhism or non-religion, showed higher experience score (p<0.001).