• Journal of Platform Technology
• /
• v.6 no.4
• /
• pp.59-68
• /
• 2018

The objective of this study is to develop an embedded antenna structure with NFC and WPC composite functions. By selecting stable materials, the optimal component ratio of the polymer sheet was determined. The low cost embedded winding method compared to the existing FPCB was devised. During the winding process, characterization and process technology were developed. We also fabricated a ferrite mold to process the WPC grooves and developed the process technology for optimizing the WPC antenna. The following conclusions were obtained. (1) Optimum composition ratio was derived as Fe 87.5%, Si 7%, Al 5.5% and selected as the final material. (2) Optimal sheet conditions were derived from the experimental evaluation method and the experimental design method through the combination test of the optimized sheet and the conventional mass production FPCB. (3) According to coil diameter and inner diameter, Q value fluctuation, resistance value and efficiency fluctuation are obtained. Therefore, the most suitable coil condition is selected and Rx matching is performed. (4) The EMV load modulation test and the cognitive distance test of the polymer sheet and the ferrite sheet showed that the recognition distance of the polymer sheet at 1k and 4K was 32-33 mm and the recognition distance of the ferrite sheet at the same condition was 30-31 mm.

• Journal of the Society of Disaster Information
• /
• v.20 no.2
• /
• pp.329-338
• /
• 2024

Purpose: This study verified the safety of the improved box-type girder behavior by comparing and evaluating the bending behavior results of a full-scale specimen based on the analytical behavior of the splice element PSC U-shaped girder with integrated tensioning systems. Method: Based on the results of the service and strength limit state design using the bridge design standard(limit state design method), the applied load of a 40m full-scale specimen was calculated and a static loading experiment using the four-point loading method was performed. Result: When the design load, crack load, and ultimate load were applied, the specimen deflection occurred at 97.1%, 98.5%, and 79.0% of the analytical deflection value. When the design load, crack load, and ultimate load were applied, the crack gauge was measured at 0.009~0.035mm, 0.014~0.050mm, and 6.383~5.522mm at each connection. Conclusion: The specimen behaved linear-elastically until the crack load was applied, and after cracks occurred, it showed strainhardening up to the ultimate load, and it was confirmed that the resistance of bending behavior was clearly displayed against the applied load. The cracks in the dry joints were less than 25% of grade B based on the evaluation of facility condition standard. The final residual deformation after removing the ultimate load was 0.114mm, confirming the stable behavior of the segment connection.

• Elastomers and Composites
• /
• v.46 no.4
• /
• pp.335-342
• /
• 2011

The virgin and recycled polyethylene composites with various ratio of fly ash were manufactured by using a fully intermeshing co-rotating twin screw extruder for the reuse of fly ash from power plant and post-consumed polyethylene. Fly ash were blended with virgin HDPE and recycled polyethylene at the weight fraction of 0 to 40 wt.%. Mechanical properties such as yield strength, abrasion resistance, and slow crack resistance were measured with ISO and ASTM standards. The experimental results for the various composites showed that the elongation at break and the yield stress of the composites decreased with increasing fly ash contents. Generally, the abrasion resistance of PEs decreased with increasing sandpaper grits but the abrasion resistance of the composites increased with fly ash content at finer abrasive surface. The slow crack growth resistance of virgin HDPE, recycled JRPE and the JRPE composite showed higher slow crack growth resistance up to 50% of load at notch depth of 20% and 30%, but KRPE and the KRPE composite showed much lower resistance than virgin HDPE, JRPE and the JRPE composite. Time to break, measured with NCLS test method, of all PEs and the composites satisfies the regulation of Korean Industrial Specification for sewer pipe and support application.

• 전자공학회논문지 IE
• /
• v.49 no.2
• /
• pp.1-8
• /
• 2012

The effects of the addition of either monoclinic $ZrO_2(pure)$ or tetragonal $ZrO_2$ containing 5.35wt% $Y_2O_3(Y-TZP)$ on the mechanical properties and thermal shock resistance of $Al_2O_3$ ceramics were investigated. The addition of $ZrO_2$(m) and Y-TZP increased sintered density of $Al_2O_3$. The Vickers hardness also increased as the volume fraction of Y-TZP increased going through a maximum at 20wt%. The hardness of the specimens was found to be dependent on the sintered density. The higher volume fraction of either $ZrO_2(m)$ or Y-TZP resulted in the higher fracture toughness of the composite was. This result may be taken as evidence that toughening of $Al_2O_3$ can be achieved by not only the transformation toughening but microcrack toughening of $ZrO_2$. The thermal shock property for $Al_2O_3-ZrO_2$ composites was improved by increasing the volume fraction of monoclinic $ZrO_2(pure)$. The grain size increased as the volume fraction of $ZrO_2$ did.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.6
• /
• pp.532-539
• /
• 1991

This study was conducted to screen genetic stock for resistant to pod shedding. Materials used were 7 recommended varieties in Korea and 211 introduced varieties containing 94 Virginia type, 99 Spanish type and 18 Valencia type varieties. the days from seeding to first anthesis. number of mature pods per plant. 100 seeds weight and shedded pod ratio per total mature pod at harvesting were investigated. And the breaking tensile strength required to detach a pod from its gynophore was measured at a proper time for harvesting of each variety. In addition. factors related to pod shedding were discussed. The first anthesis of Spanish and Valencia types were earlier than that of Virginia type, but Korean recommended varieties which were recognized as Virginia type had relatively earlier anthesis. The varieties of Spanish type yielded more pods compared with those of Valencia and Virginia types. but Korean recom-mended varieties yielded slightly more pods than the others. Seeds weight of Korean recommended varieties was larger than not merely those of Spanish and Valencia types which were small seeds but also those of Virginia type which were large seeds. The breaking tensile strengths between pod and gynophore were various among the varieties belonging to same type. The strength was relatively strong in the Spanish type, but weak in both Virginia type and Korean recommended varieties. Therefore, pod shedding in the varieties of Spanish type was low and high in Virginia type and Korean recommended varieties. There were positive or negative correlations at the 0.1 % significan level among the days to first anthesis. number of pods per plant. seed weight, breaking tensile strength and shedding ratio. The pod shedding is considered a compound character that is affected by the factors such as breaking tensile strength between pod and gynophore, number of pods per plant and seed size.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.83-83
• /
• 2017

생체재료의 표면은 이식과 동시에 생체계면의 역할을 하게 되어, 일련의 생물학적 반응이 시작되고 진행되는 중요한 장소가 된다. 초기에 생체계면에서 일어나는 단백질 흡착이나 염증반응을 비롯한 생물학적 반응들은 궁극적으로 임플란트의 성패를 좌우할 만큼 중요하다. 골융합을 개선하기 위한 다른 방법으로 생체불활성의 타이타늄 (Ti)과 골조직의 능동적인 반응을 이루기 위해 생체활성 표면을 부여함으로서 계면에서의 골형성 반응을 증진시키는 방법이 이용된다. 생체불활성의 Ti과 Ti합금은 골조직과 직접적인 결합을 이루지 못하므로, 골조직과의 반응을 향상하기 위해 여러 종류의 생체활성 재료를 코팅하는 방법이 연구되어 왔고, 이 중 생체의 변화와 가장 유사한 하이드록시아파타이트 코팅이 가장 대중적인 방법으로 사용되었으며 이는 초기 골형성을 촉진하는 것으로 알려졌다. 치과용 임플란트의 표면형상과 화학조성이 골 융합에 영향을 미치는 가장 중요한 인자이므로 최근의 연구동향은 이들 두 가지 표면특성을 결합함으로서 결과적으로 최적의 골세포반응을 유도하고, 골융합 후 골조직과의 micromechanical interlocking에 의해 임플란트의 안정성에 중요한 역할을 하는 마이크론 단위의 표면조도와 표면 구조를 유지하면서, 부가적으로 골 조직 반응을 능동적으로 개선할 수 있는 생체활성 성분을 부여하여 골 융합에 상승효과를 이루기 위한 표면처리법에 관해 많은 연구가 요구되어지고 있다. 따라서 골을 구하는 원소인 망간과 실리콘으로 치환된 하이드록시아파타이트를 플라즈마 전해 산화법으로 코팅하여 세포와 잘 결합할 수 있는 표면을 제공함으로써 골 융합과 치유기간을 단축시킬 수 있을 것으로 사료된다. 실험방법은 시편은 치과 임플란트 제작 합금인 Ti-6Al-4V ELI disk (grade 5, Timet Co., USA; diameter, 10 mm, thickness, 3 mm)이며, calcium acetate monohydrate, calcium glycerophosphate, manganese(II) acetate tetrahydrate, sodium metasilicate을 설계조건에 따라 혼합 제조된 전해질 용액을 이용하여 플라즈마 전해 산화법으로 표면 코팅을 실시하였다. 각 시편의 플라즈마 전해시 전압은 280V로 인가하였고, 전류밀도는 70mA로 정전류를 공급하여 해당 인가전압 도달 후 3분 동안 정전압 방식을 유지하였다. 코팅된 피막 표면을 주사전자현미경과 X-선 회절분석을 통하여 미세구조 및 결정상을 관찰하였다. 또한 코팅된 표면의 생체활성 평가는 정량적으로 평가하기 위해 동전위시험과 AC 임피던스를 통하여 시행하였다. 분극거동을 확인하기 위해 potentiostat (Model PARSTAT 2273, EG&G, USA)을 이용하여 구강 내 환경과 유사한 $36.5{\pm}1^{\circ}C$의 0.9 wt.% NaCl에서 실시하였다. 전기화학적 부식 거동은 potentiodynamic 방법으로 조사하였고 인가전위는 -1500 mV에서 2000 mV까지 분당 1.67 mV/min 의 주사속도로 인가하여 시험을 수행하였다. 임피던스 측정은 potentiostat (Model PARSTAT 2273, EG&G, USA)을 이용하였으며, 측정에 사용한 주파수 영역은 10mHz ~ 100kHz 까지의 범위로 하여 조사하였고 ZSimWin(Princeton applied Research, USA) 소프트웨어를 사용하여 용액의 저항, 분극 저항 값을 산출하였다. 망간의 함량이 증가할수록 불규칙한 기공을 보였으며, 실리콘은 $TiO_2$ 산화막 형성을 저해하는 경향을 확인할 수 있었다. 단독으로 표면을 처리한 경우보다 두 가지 원소를 이용해 복합 표면처리를 시행한 경우가 내식성이 좋아 임플란트과의 골 유착에 긍정적인 영향을 미칠 것으로 사료된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.395-396
• /
• 2011

본 논문에서는 30% 내외의 평균반사율을 가지는 다결정 실리콘 태양전지의 입사광 손실을 최소화하여 광전변환효율 극대화를 구현하기 위해서 SF6/O2 혼합가스를 이용한 RIE 표면 texturing 공정을 수행하였다. 현재 다결정 실리콘 태양전지는 다양한 방향의 grain을 가지기 때문에 단결정 실리콘에 적용되는 습식 식각 방식이 다결정 실리콘 표면 texturing에 적절하지 않은 것으로 알려져 있다. 이를 개선하기 위해서 이방성 식각 특성을 가지는 다양한 texturing 방법이 시도되고 있다. 대표적으로 기계적인 방식의 V-grooving, 레이저 grooving, 플라즈마 건식식각을 이용한 texturing 및 산 용액을 이용한 texturing 등의 연구가 보고되고 있다. 그 중에서 플라즈마 건식식각 방식의 하나인 RIE를 이용한 표면 texturing 공정이 간단한 공정과 산업계 응용의 용이성 때문에 활발히 연구되어 왔다. 특히 Sandia group과 일본 Kyocera사의 연구 결과에서는 그 가능성을 입증하고 있다. 본 연구에서는 공정의 단순화와 안전한 공정을 위해서 SF6/O2 혼합 가스를 이용하여 마스크 패턴 공정없이 RIE texturing 공정을 수행하였으며, RIE-textured 다결정 실리콘에 대해서 태양전지를 제작하여 표면 texturing이 광전변환효율에 미치는 영향에 대해서 분석하였다. 그 결과 SF6/O2 혼합 가스를 이용한 RIE texturing은 다결정 실리콘 표면에 주로 needle 구조를 형성하는 것을 확인하였다. 각 texturing 조건별 반사율의 차이는 needle 구조의 조밀도와 관련되는 것을 알 수 있었으며, 동일 공정 parameter 상에서 식각 시간 1, 2, 3, 4, 5분 기준 시간에 따른 표면 구조 분석 결과 seed 가 형성되고 그에 따라서 needle 형태로 식각되는 과정을 관찰하였다. 반사율은 분당 약 4%씩 낮아져 5분 식각 후 14.45% 까지 낮아졌으며, 표면 구조에서 폭은 약 30 nm로 모두 일정하며, 길이가 약 20, 30, 50, 80, 100 nm으로 증가되었다. 이 결과로 보아 seed로부터 needle 구조가 심화되어가는 것을 알 수 있었다. 시간에 따른 RIE texturing 후 제작된 태양전지는 효율이 1분 식각 기준 15.92%에서 약 0.35% 씩 낮아져 5분 식각 후 14.4%로 낮아졌다. Voc 는 texturing 시간에 관계없이 일정하며 Isc가 점점 감소되는 것으로 확인되었다. EQE 결과도 이와 동일하게 RIE texturing 시간이 길어질수록 전체 파장 범위에서 일정하게 낮아지는 것이 관찰되었다. Electroluminescence(EL) 이미지 결과 texturing 시간이 길어진 태양전지일수록 점점 어두운 이미지가 나타나 5분 식각의 경우 가장 어두운 결과를 나타내었다. 이런 결과는 한 가지 이유보다는 복합적인 문제로 예상되는데 궁극적으로는 RIE 공정 후 표면에 쌓인 charged particle들이 trap 준위를 형성하여 효율 및 공정상에 영향을 미친 것으로 보이며, 특히 잔류 O기가 불균일한 산화막을 형성하는 것으로 예상된다. 또한 EL 분석 결과를 볼 때 RIE texturing 공정이 길어질수록 불안정한 pn-junction을 형성하는 것을 확인하였으며, emitter 층 형성 후 PSG (phosphorous silica glass) 공정에서 needle의 상부 구조가 무너지면서 면저항이 증가된 결과로 분석된다. PSG 제거 후 측정된 면저항의 경우 3분 texturing 샘플부터 면저항이 약 4${\Omega}/sq$ 정도 증가됨을 확인하였다.

• Korean Chemical Engineering Research
• /
• v.43 no.3
• /
• pp.425-431
• /
• 2005

New type of supercapacitor using high surface area activated carbons mixed with high conductivity polypyrrole (Ppy) has been prepared in order to achieve low impedance and high energy density. Mixed carbons of BP-20 and MSP-20 were used as the active electrode material, and polypyrrole doped with 2-naphthalenesulfonic acid (2-NSA) and carbon black (Super P) as conducting agents were added to activated carbons in order to enhance good electric conductivity. Electrodes prepared with the activated electrode materials and the conducting agents were added to a solution of organic binder [P(VdF-co-HFP) / NMP]. The ratio of optimum electrode composition was 78 : 17 : 5 wt.％ of (MSP20 : BP-20=1 : 1), (Super P : Ppy=10 : 7) and P(VdF-co-HFP) respectively. The performance of unit cell with addition of 7 wt％ Ppy have shown specific capacitance of 28.02 F/g, DC-ESR of $1.34{\Omega}$, AC-ESR of $0.36{\Omega}$, specific energy of 19.87 Wh/kg and specific power of 9.77 kW/kg. With addition of Ppy, quick charge-discharge of unit cell was possible because of low ESR, low charge transfer resistance and quick reaction rate. And good stability up to 500 chargedischarge cycles were retained about 80％ of their original capacity. It was concluded that the specific capacitance originated highly from compound phenomena of the pseudocapacitance by oxidation-reduction of polypyrrole and the nonfaradaic capacitance by adsorption-desorption of activated carbons.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.33 no.6
• /
• pp.246-256
• /
• 2021

Various development projects occurring on the coast cause an imbalance of surface sediments, causing coastal disasters or irreversible coastal erosion. Coastal erosion caused by the influence of various port structures built through coastal development can be directly identified by evaluating changes in the sediment budget, longshore sediment, and cross-shore sediment. In other words, it will be possible to evaluate the causality between coastal development and coastal erosion by classifying regions due to single cause and regions due to multiple causes according to the changes in the sediment classified into the three types mentioned above. In this study, the cause of long-term and continuous erosion was analyzed based on the analysis results of the coastal development history and the Coastal Erosion Monitoring targeting the coast of Gangwon-do and Gyeongsangbuk-do on the east coast. In addition, in order to evaluate the degree of erosion caused by the construction of artificial coastal structures, the concept of erosion impact assessment was established, three methods were proposed for the impact assessment. The erosion impact of Hajeo port was assessed using the results of satellite image analysis presented in the Coastal Erosion Monitoring Report, it was assessed that the development of Hajeo port had an impact of 93.4% on erosion, and that of the coastal road construction had an impact of 6.6%.

• Journal of Digital Convergence
• /
• v.19 no.11
• /
• pp.525-536
• /
• 2021

This study investigated that customer satisfaction based on the effects of perceived value (innovative value, practical value, symbolic value) and innovation characteristics (innovative resistance, visibility) of wearable healthcare device users on purchase attitude. A survey was conducted on actual users who are currently using wearable healthcare devices, and the final 201 copies were analyzed using SPSS 25 and SmartPLS 3.0. The summary of research results is following here. First, it was found that the perceived values, innovative and practical values had a positive (+) effect on the user's purchasing attitude, while symbolic values did not affect the user's purchasing attitude. Second, among the innovation characteristics, innovation resistance was came out negative (-) effect on the user's purchasing attitude, and among the innovation characteristics, visibility did not affect the user's purchasing attitude. Third, it was found that perceived price had a positive (+) effect on the user's purchase attitude. Fourth, it was clarified that the perceived price and purchase attitude had a positive (+) effect on the user's customer satisfaction. Based on these research results, theoretical, practical, and future research directions were proposed.