• Composites Research
• /
• v.14 no.6
• /
• pp.32-37
• /
• 2001

It is known that recoating or protection with glass-tube can prevent FBG sensor from being affected by birefringence. However, the effect on the strain transfer of such treatment has not been verified yet. Three types (uncoated, recoated and glass-tube protection) of FBG sensors are fabricated to verify the effect on the strain transfer of each treatment. The strain from each sensor embedded into a graphite/epoxy composite specimen was compared with that of ESG attached on the surface through the tensile test. And the signal characteristics of each sensor were also compared using the tensile test of a tapered aluminum specimen which was under the state of strain gradient.

• Korean Journal of Optics and Photonics
• /
• v.13 no.3
• /
• pp.245-250
• /
• 2002

We study numerically the temporal evolutions of two orthogonally polarized pulses with width less than 100fsec in all-optical phase-shift switches. We analyze the complicated interplay between a soliton pulse and a higher-order soliton pulse, including the self-and the cross-Raman scattering and the walk-off effect. We also investigate the influence of these interactions on switching performance, including pulse-shape, phase-shift distribution, and contrast ratio. In particular we show that an optical fiber with a typical birefringence (Δn : 2.4$\times$10$^{-5}$ ) can be used with good switching performance in such all-optical switches.

• Korean Journal of Optics and Photonics
• /
• v.12 no.1
• /
• pp.5-9
• /
• 2001

A wavemeter was realized using the phenomena that the phase lag between principal polarization states in an optical retarder is a function of wavelength. The change in the polarization state of the optical beam as it passes through the optical retarder is dependent on wavelength. The wavelength of the optical beam is determined by comparing the power difference between principal polarization states. A prototype wavemeter was successfully implemented using a polarization maintaining fiber with birefringence $3\times10^{-4}$ and length 100 mm as the optical retarder. The measurement resolution was 0.08 nm over a wavelength region of 1554.38 nm-1557.l9 nm, which agreed well with theoretically calculated results. In addition, the dependence of operating characteristics on temperature was analyzed theoretically and experimentally.mentally.

• The Korean Journal of Rheology
• /
• v.1 no.1
• /
• pp.63-70
• /
• 1989

고밀도 폴리에틸렌과 폴리프로필렌을 용융혼합하여 블렌드를 만들었다. 압출물의 morphology 와 유변학적 성질을 측정하고 그 용융하고 섬유의 X-선 회절, 인장 성질, 복굴 절률등과 관련하여 고찰하였다. 파단면의 SEM 사진으로부터 폴리에티렌 성분비가 25%, 50% 에서는 폴리프로필렌이, 75%에서는 폴리에틸렌이 연속상을 이루며 분산상은 고르게 분포함을 알았다 점도와 용융탄성은 모두 폴리에틸렌이 폴리프로필렌보다 크며 블렌드에서 는 그중간에 위치 하였다. 폴리에틸렌의 함량의 증가에 따라 압풀물의 제 1법선 응력차는 증가하였고따라서 방사 섬유의 복굴절률도 증가하였으며 초기 탄성률도 증가하는 경향을 보 였으나 결정 배향도는 조성 의존성을 갖지 않는다. 두 고분자의 비상용성으로 인해 강도는 짓선성에서 벗어나는 거동을 나타내었다.

• Korean Journal of Optics and Photonics
• /
• v.11 no.1
• /
• pp.33-36
• /
• 2000

KrF excimer laser, which is useful for fabrication of fiber gratings, was irradiated on the PLC-type WDM directional coupler and the transmission wavelength shift was observed as a function of UV exposure time. The effective refractive index change of rectangular silica waveguide was calculated from the wavelength shift measurement and the coupled mode theory. heory.

• Composites Research
• /
• v.15 no.3
• /
• pp.30-38
• /
• 2002

Fiber Bragg grating(FBG) like other optical fiber sensors also has the merit of embedding capability. To increase their actual value related to embedding capability, this paper reported the reliability and signal characteristics of FBGS embedded in composite laminates. The microphotographs of embedded optical fibers visualized the embedding environments of stripped optical fibers and coated optical fibers. Based on these microphotographs and cure monitoring performed using FBGs, we could understand that the main cause breaking the unique Bragg condition of low-birefrigence FBG were residual stress artier curing and reported the stale of stress/strain of optical fiber quantitatively. The cure monitoring also showed the history of splitting peak of a stripped FBG along cure processing. In addition, we could obtain a transverse insensitive grating(TIG) with ease by recoating a stripped FBG. TIG has good advantage for real-time signal processing.

• Korean Journal of Optics and Photonics
• /
• v.10 no.3
• /
• pp.248-253
• /
• 1999

In this paper, we have investigated a fiber type active coupler which utilizes the mode coupling between the side polished single mode optical fiber and the active multimode planar waveguide. The proposed device can be used for not only tunable wavelength filter or optical intensity modulator but also a tool for measuring optical properties of guiding material such as refractive index, birefringence, electro-optic coefficient, and thermo-optic coefficient. We gave designed and optimized a coupler structure using the BPM and fabricated the device using thermo-optic polymer as active planar waveguide overlay. The device showed that insertion loss was less then 0.5 dB, extinction ratio was -13 dB at the resonance wavelength, and the wavelength tunablity due to thermo-optic effect was -1.5 nm/$^{\circ}C$. The active coupler using thermo-optic effect can be used as a wavelength tunable filer, an optical intensity modulator and an optical sensor. pulses that are subsequently compressed by a dispersive optical fiber. Experimental results show that $sech^2$ shape pulses with a pulse width of ~14 ps and a time bandwidth product of ~0.34 are successfully generated at 10 GHz repetition rate. In contrast to other methods, such as higher order soliton compression, this approach does not depend on the optical power and thus shows promise for application to low-power lasers.

• Korean Journal of Optics and Photonics
• /
• v.11 no.1
• /
• pp.13-18
• /
• 2000

The SiOxNy thin films were prepared on Si(lOO) by reactive RF sputtering method. The reactive gas ratio and the power were used as parameters for depositing SiOxNy thin fims. The properties of ${SiO_x}{N_y}$ thin tilms were investigated by XRD, XPS, refractive index and extinction coefficient analyzer (n'||'&'||'k analyzer), and FfIR. It was found by the results of the x-ray diffraction measurement that SiOxNy thin films were grown to an amorphous structure. From the results of the XPS, and the n'||'&'||'k analyzer, it was found that refractive index was intended to increase with the increasement of the relative nitrogen contents of the ${SiO_x}{N_y}$ thin films.

• Fashion & Textile Research Journal
• /
• v.15 no.6
• /
• pp.985-992
• /
• 2013

Polytrimethylene terephthalate(PTT) offers several advantageous properties such as good tensile strength, uniformity, stiffness, toughness, UV stability, resilience, stain resistance, outstanding elastic recovery, and dyeability. The effects of annealing temperature on physical properties and the structure of PTT filaments and yarn were investigated by measuring wide-angle X-ray diffraction (WAXD), density, optical birefringence, dynamic visco elasticity, and tensile testing. The intensity of maximum tan ${\delta}$ decreased and the temperature of maximum tan ${\delta}$ shifted to a higher temperature as the annealing temperature of filaments increased; however, it shifted to a lower temperature when the annealing temperature exceeded $130^{\circ}C$. In addition, crystallinity, density and D-spacing of (010) crystal face increased as the annealing temperature increased. Optical birefringence and specific stress were almost constant up to $100^{\circ}C$ and then decreased above $130^{\circ}C$. The shrinkage of PTT filament is 0 in boiling water when annealed above $130^{\circ}C$; consequently, the use of annealed fiber above $130^{\circ}C$ can remove thermal instability when dyeing PTT fiber. In the case of yarns, the thermal stability and physical properties of yarns showed the best effect when the ply number is less than 5, twist number is less than 400tpm, and the annealing time is 20minutes.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.144-149
• /
• 2014

Large residual stresses are remained in the conventional injection molded products because of the high cavity pressure in packing phase during injection molding process. Conventional injection molding (CIM) invokes distribution of cavity pressure and it has a limitation to obtain product with uniform physical property. Multi-cavity conventional injection molding contains quality deviation among the cavities since flow imbalance occurs during filling phase. Injection compression molding (ICM) is adopted to overcome these limitations of CIM. In this study, molding characteristics of CIM and ICM have been investigated using multi-cavity injection mold. Researches were performed by both experiment and computer simulation through observations of birefringence for transparent resins, polycarbonate and polystyrene in CIM and ICM. As a result, low and uniform birefringence and mold shrinkage were showed in the specimens by ICM that could give a uniform cavity pressure. Deviation of physical property among the specimens in multi-cavity mold shown in CIM was significantly reduced in the specimens by ICM. Through this study it was concluded that the ICM in multi-cavity molding was valid for molding products with uniform property in an individual cavity and also reduced property deviation among the cavities.