• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.10-14
• /
• 2016

육상의 증발산량(evapotranspiration, ET)은 대기 중 수증기의 상변화를 통해 대기와 지표 사이의 물과 에너지 순환에 영향을 미치며, 강수량, 유출량과 함께 수자원에 영향을 미치는 주요 인자이다. 강수량과 유출량은 직접 관측이 가능한 반면, 증발산량은 숨어있는 잠열로서 관측하기 어렵다. 플럭스 타워나 라이지메타(Lysimeter) 등을 이용하여 증발산량을 직접 관측하고 있으나 이들 지상관측은 일부 지점(point)에서 제한적으로 이루어지고 있으며, 관측 지점의 수를 확대하게되면 관측 기기의 유지 보수 등의 많은 시간과 비용이 든다는 한계가 있다. 이러한 지상관측의 한계를 극복하고 넓은 영역의 증발산량 변화를 관측하기 위해 위성을 이용한 증발산량을 추정하는 연구가 활발히 진행되고 있다. 기상청 국가기상위성센터(National Meteorological Satellite Center, NMSC)에서는 우리나라 최초의 정지 기상 위성인 천리안 위성(Communication, Ocean and Meteorological Satellite, COMS) 자료를 지표 에너지 수지식(Surface Energy Budget Equation)에 적용하여 동아시아 지역의 지면과 식생 특성을 반영한 '일(daily) 증발산량 산출 알고리즘'을 개발하였다. 현열을 계산하기 위해 다양한 입력 변수가 사용되어지고 계산 과정이 복잡하기 때문에, 본 연구에서는 '반 경험적인 계수인 B 계수 모델'을 사용하여 현열 산출 기법을 단순화하였다. 본 알고리즘을 이용하여 2011년 4월부터 현재까지 동아시아(위도 $20{\sim}50^{\circ}N$, 경도 $100{\sim}145^{\circ}E$)의 해상도 1km의 일 증발산량을 산출하였고, 위성 증발산량의 검증을 위해 지면 특성이 다른 청미천(농경지), 설마천(혼효림) 지역의 플럭스 타워 증발산량 자료(유량조사사업단 제공)와 비교 분석하였다. 2011년 4월부터 2014년 12월까지 청미천 지역에서의 플럭스 타워 관측과 비교한 결과, 총 665개 자료에 대하여 RMSE는 2.82 mm/day, Bias는 2.56 mm/day의 결과를 보였다. 동일한 기간에 대하여 설마천 지역에서의 플럭스 타워 관측과 비교한 결과, 총 582개 자료에 대하여 RMSE는 1.92 mm/day, Bias는 1.45 mm/day의 결과를 보였다. 기상청 국가기상위성센터의 위성증발산량이 봄과 가을철에 다소 높게 산출되는 경향이 있었으나, 증발산량의 변화경향은 유사하게 나타났다. 이러한 결과를 바탕으로 동아시아 지역 위성 증발산량 변화를 감시하고 있으며 향후, 수문 및 기후 분야에서 가뭄 모니터링 등의 연구에도 활용할 수 있을 것이다.

• Journal of the Korean Society for Railway
• /
• v.10 no.5
• /
• pp.527-532
• /
• 2007

In this paper, we suggest those two design plans for power supply method of Hot Standby Sparing System; one is the plan using MTBF based on Constant Failure Rate, and the plan using Reliability Function is the other. Traditionally, RBD (Reliability Block Diagram) is used for reliability prediction which is required to meet any requirements before system operation. However, the system that has redundancy, such as Hot Standby Sparing System, Is not suitable for system reliability modeling using combination model, such as RBD. In this paper, therefore, we demonstrate that for redundancy controller, redundancy modeling design toward fault occurrence design is more effective to build up a system with higher reliability and achieve the effectiveness of loss cost due to maintenance and failure occurred in operation, rather than combinational modeling design.

• Journal of the Korean Society for Railway
• /
• v.17 no.5
• /
• pp.373-380
• /
• 2014

With a view to the commercialization of the Korean automatic variable-gauge bogie in the Eurasia railway system, the aim of this research was to perform an economic analysis concerning the possible introduction and operation of this bogie at the present time. For this purpose, we compared the possible types of freight connection service for container transportation, transshipment and the gauge-adjustable system, estimating the total life-cycle cost (LCC) incurred by each system, depending on type and quantity, over the whole process of acquisition, operation, maintenance and disposal. Based on this, we presented a case-by case analysis. Furthermore, in estimating economic feasibility, we analyzed the cost-benefit ratio taking into account not only the objective LCC, but also the reduced time required for the gauge-change and customer convenience. After estimating the LCC and analyzing the cost-benefit ratio of the respective systems, we demonstrated the economic superiority of view of the gauge adjustable system.

• Nuclear Engineering and Technology
• /
• v.14 no.2
• /
• pp.86-91
• /
• 1982

In 1977, spent fuel storage capacity of Ko-Ri Unit 1 was raised to contain 4-2/3 core, by reducing the center-to-center spacing between fuel assemblies from 53.34cm to 36cm. In this paper the adequacy is discussed in detail by examining the previous design analysis report. According to the analytic method presented by Core Performance Branch, study on credible abnormal moderator density condition is performed by using KENO-IV for the redesigned spent fuel storage facility. Result shows that 36cm for the center-to-center spacing between fuel assemblies is not enough to keep the storage safe at water density of 0.1143g/㎤, which gives the maximum $K_{eff}$ 0.9958$\pm$0.0048, which exceeds the CPB regulation limit 0.98. From sensitivity study regarding to the center-to-center spacing, it should be maintained to space greater than 43cm in order to meet the CPB requirements.s.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.375-382
• /
• 2021

Self-healing concrete is in the spotlight in that it can effectively extend the lifespan of concrete structures by healing cracks in the structure by themselves without additional repairing or retrofiting actions. Currently, self-healing concrete is a field that is being actively studied around the world, but since most studies focus on the improvement of healing performance, there is a lack of methods to rationally evaluate the self-healing performance of concrete. Although the gas diffusion test method has been developed for the use in the performance evaluation of self-healing concrete, it has revealed that for gas diffusion through the matrix affect the crack diffusion coefficients depending on the environmental conditions such as the saturation of the specimen, the temperature, and humidity during the experiment. Therefore, in this study, the method has been proposed to eliminate the influence of the matrix diffusion when calculating the crack diffusion coefficient. In addition, a pre-conditioning process was introduced to shorten the experimental time. As a result, the crack width could be estimated with an error level of less than 3% in the test time of about 20 minutes.

• Journal of Advanced Navigation Technology
• /
• v.23 no.4
• /
• pp.273-280
• /
• 2019

There are many studies that use structure health monitoring to reduce maintenance costs for aircraft and to increase aircraft utilization. Many studies on FBG sensors are also being conducted. However, if the FBG sensor is installed inside the composite, voids will occur between the layers of the composite, resulting in signal split problem. In addition, the FBG sensor is not affected by electromagnetic waves, but will produce electromagnetic noise caused by electronic equipment during post-processing. In this paper, to reduce the error caused by these noises, the stationary wavelet transform, which has the characteristics of movement immutability and is efficient in nonlinear signal analysis, is presented. And in the above situation, we found that noise rejection performance of stationary wavelet transform was better compared with the wavelet packet transform.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.11 no.6
• /
• pp.27-40
• /
• 2001

In an offline system, the bank does not participate in payments. As a result, it is difficult to make the refund spendable. Due to this, current offline systems do not provide spendable refunds. In these systems, a check consists of two parts: a spendable part and a refund part. A client uses the spendable part during the payment phase, and uses the refund part to get the refund for the remainder of the check. Therefore, a client cannot reuse the remaining and must always refund it. Moreover, the relationship between the spent amount and the refund amount can be used to guess which check the client used when the client refunds the remaining. To remedy these problems, we propose a new offline system which allow clients to reuse the remaining values of the check. This system provides unlinkability of the payments made by using a single check. It also provides mechanisms to detect and identify clients who perform misconduct such as double spending and over spending. The required overall computational cost to withdraw, spend and refund a check in our system is lower than using several checks in other offline systems.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.6
• /
• pp.1145-1150
• /
• 2020

After the Davos Forum, the recent 4th Industrial Revolution has become an area of interest to countries around the world. Among the technologies of the 4th industrial revolution, the ubiquitous computing environment requires a convergence environment of various devices, networks, and software technologies, and the RFID technology that identifies objects among the IoT technology fields is applied to all industries and has a competitive edge. Systems to which RFID technology is applied are being used in various industrial fields, especially! It is efficiently used for accurate inventory management and SCM management in the field of distribution and logistics. If the RFID system is built in a cloud-based environment, it will be possible to secure reliability in distribution management in consideration of an effective logistics management system and economic feasibility. This study is a study on the RFID system in a cloud computing environment to reduce the cost of operating or maintaining an application server to improve the economy and reliability.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.31 no.3
• /
• pp.401-410
• /
• 2021

Recently, as cyber attacks targeting industrial control systems increase, various studies are being conducted on the detection of abnormalities in industrial processes. Considering that the industrial process is deterministic and regular, It is appropriate to determine abnormality by comparing the predicted value of the detection model from which normal data is trained and the actual value. In this paper, HAI Datasets 20.07 and 21.03 are used. In addition, an ensemble model is created by combining models that have applied different time steps to Gated Recurrent Units. Then, the detection performance of the single model and the ensemble recurrent neural networks model were compared through various performance evaluation analysis, and It was confirmed that the proposed model is more suitable for abnormal detection in industrial control systems.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.30 no.6
• /
• pp.1189-1206
• /
• 2020

Recently, ICT companies do not directly design, develop, produce, operate, maintain, and dispose of products and services, but are outsourced or outsourced companies are increasingly in charge. Attacks arising from this are also increasing due to difficulties in managing vulnerabilities for products and services in the process of consignment and re-consignment. In order to respond to this, standards and systems for security risk management of ICT supply chain are being established and operated overseas, and various case studies are being conducted. In addition, research is being conducted to solve supply chain security problems such as Software Bill of Materials (SBOM). International standardization organizations such as ISO have also established standards and frameworks for security of ICT supply chain. In this paper, we presents ICT supply chain security management items suitable for domestic situation by comparing and analyzing ICT supply chain security standards and systems developed as international standards with major countries such as the United States and EU, and explains the necessity of cyber security framework for establishing ICT supply chain security system.