• Journal of the Korean Geotechnical Society
• /
• v.35 no.12
• /
• pp.7-13
• /
• 2019

In the case of the drilled shaft, one of the methods for calculating unit skin friction stress of rock socket parts is to measure the roughness of the excavated face. This method is to estimate the unit skin frictional resistance using a device which measures the roughness shape of the excavated face in the excavation step. In this study, the roughness shapes of the face of the rock socket part in the drilled shaft were measured directly in the perforated hole and the results are used to identify the characteristics of the unit skin friction of the bedrock. In addition, the static load test and the load transfer test were performed on the same pile to verify the result of the roughness test.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.1
• /
• pp.39-53
• /
• 2018

Generally, the total ventilation resistance coefficient in a tunnel consists of inlet/outlet loss coefficient, wall friction coefficient, and other loss coefficient caused by sudden expansion and contraction of cross-section, etc. For the tunnel before opening, when the running ventilation fan is stopped, the wind speed in the tunnel is reduced by the total ventilation resistance drag. The velocity decay method is comparatively stable and easy to estimate the wall friction coefficient in the pre-opening tunnel. However, the existing study reported that when the converging wind speed is a negative value after the ventilation fan stops, it is difficult to estimate the wall friction coefficient according to the velocity decay method. On the other hand, for the operating tunnel in which the piston effect acts, a more complex process is performed; however, a reasonable wall friction coefficient can be estimated. This paper aims at suggesting a method to minimize the measurement variables of the piston effect and reviewing a method that can be applied to the operating tunnel. Also, in this study, a new method has been developed, which enables to calculate an variation of the piston effect if the piston effect is constant with a sudden change of external natural wind occurring while the wind speed in the tunnel decreases after the ventilation fan stops, and a programming logic has been also developed, which enables dynamic simulation analysis in order to estimate the wall friction coefficient in a tunnel.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.6
• /
• pp.21-30
• /
• 2023

One of the methods for calculating unit skin friction of soft-rock-socket parts for cast-in-place piles involves the roughness measurement of the parts. The measurements are conducted during the excavation stage. A roughness measuring device is installed in the excavation hole and the unit skin friction is calculated from the measured surface roughness of the rock socket. Herein, the results of roughness measurement of rock-socket parts in cast-in-place piles and that of load transfer tests are analyzed and compared. The unit skin friction from the roughness measurements can be converted into unit skin friction corresponding to the displacement of a pile generated in a load transfer test. A reduction factor is given as R_f = -0.14n + 1.48.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.189-193
• /
• 2010

RMA-2, Telemac-2D, River2D 등 기존의 대부분 국내외 상용모형에서는 내부 경계인 하천구조물과 외부 경계인 측벽에서의 경계조건을 활동조건(slip condition)으로 가정하여 흐름장을 계산하였다. 그러나 실제로 벽면에서는 마찰력에 의해 흐름이 존재하지 않는 무활조건(no slip condition)이 물리적으로 타당하다. 따라서 본 연구에서는 내부구조물인 교각이 존재하는 영역에서의 수평 2차원 유속분포를 구하기 위해 천수방정식을 Galerkin법과 Newton-Raphson법에 의해 이산화한 수치모형을 개발하였다. Yulistiyanto 등(1998)이 수치모의 및 수리실험에 사용한 조건을 채택하여 벽면에서의 접선방향 유속이 존재하는 활동조건과 벽면에서 유속이 없는 무활조건을 부여하고 교각을 포함한 수로에서 유속, 수위 및 전단분포를 해석하였다. 활동경계조건을 적용한 경우 교각 표면을 따라 큰 유속이 분포하고 후면에서도 관성력에 의해 흐름방향 유속이 두드러지게 나타났으나 무활조건을 적용한 경우 교각 후면에서 와가 형성되고 후류현상이 두드러지게 나타났다. 무활조건을 적용한 경우 교각 전면부에서는 선수파(bow wave)가 4 cm정도 높게 나타났으며 교각 측면부에서는 2 cm 높게 나타났다. 반면 교각 후면에서는 후류의 영향으로 수면이 2 cm 낮게 분포하였다. 교각부에 작용하는 전단력을 분석한 결과 무활조건을 적용한 경우가 활동조건을 적용한 경우에 비해 최대 6배 높은 전단력이 나타났다.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.2
• /
• pp.347-354
• /
• 2008

Steel plate-concrete (SC) structure has recently been used in nuclear power structure because of its construction efficiency. In this study, experimental and analytical study to investigate the behavior of the SC structure's wall slab connection was carried out. Experiments were performed for typical SC and RC connections in order to examine the basic difference between each structure. Finite element analysis was performed and the result of the analysis was found to closely reflect the experimental result. By varying the thickness of the shear plate and friction coefficients and the distance of applied load from the wall, the influence of the parameters on the joint strength and failure modes were examined. Finally, it was confirmed that the joint strength formula proposed in th this research gives conservative results.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.2
• /
• pp.67-76
• /
• 2017

In this study, the effect of caisson heel on the active earth pressure is investigated. Using limit analysis method, inclinations of slip surface developed above the heel with different lengths are analyzed. The shorter the heel length, the larger those of inside slip surface, however those of outside slip surface are not changed. According to the relative heel length, relationships of internal friction angle of backfill material - wall friction angle between caisson structure and backfill - friction angle acting on virtual section at the end of heel are presented. Earth pressures acting against caisson structure with relatively short heel are smaller than Rankine earth pressure but always greater than Coulomb earth pressure which does not consider the heel length.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.15-15
• /
• 2000

제트 베인에 의한 추력 방향 제어 장치는 롤 운동 제어를 가능하게 하고, 큰 선회 각도를 얻을 수 있는 장점이 있으나, 기계 장치가 비교적 복잡하고, 제트 베인의 열적, 구조적 문제를 해결하여야 한다. 복잡한 기계 장치는 유동 해석의 측면에서 고려해 볼 때 격자 형성을 어렵게 만들어 유동장 해석을 통한 성능예측을 어렵게 만든다. 구조물의 응력해석을 위하여 제트 베인 표면에서의 정압력과 더불어 마찰력도 고려하여야 하는데, 정확한 마찰력 계산을 위해서는 난류 모델링이 필수적이고, 그에 따라 벽면 근처에서 격자를 밀접시키는 것이 요구된다. 본 연구에서는 상용 유동해석 소프트웨어인 Fluent를 사용하여 제트 베인이 장착된 추력 방향 제어 장치의 3차원 난류 유동장 계산을 수행하였다. 피치, 요 운동의 경우와 롤 운동의 경우로 구분하여 계산하였으며, 최대 받음각을 $25^{\cire}$ 로 하여 제트 베인의 받음각에 따라 회전축에 작용하는 힘과 모멘트를 계산하였다. 본 연구의 결과는 향후 개발될 제트 베인이 장착된 추력 방향 제어 장치의 개념설계 단계에 필요한 기본자료로서 신뢰도를 높이는데 도움이 되리라 판단된다.

• The Journal of the Korea Contents Association
• /
• v.15 no.2
• /
• pp.499-506
• /
• 2015

The friction velocity is a quantity with the dimensions of velocity defined by the friction stress and density of a wall surface at near wall of flow condition. Also, the friction velocity is the hydraulic parameter describing shear force at the bottom flow. Moreover, it is a very important factor in designing open channel and essential to determine the mixing coefficient in the main flow direction. The estimation of the friction velocity are such as methods using channel slope, linear law of the mean velocity at viscous sub-layer and direct measurement of wall shear stress, etc. In the present study, we propose a friction velocity equation that has been optimized by combining the concept of entropy, which is used in stochastic method, and to verify the proposed equation, the experimental data measured by Song was used. The R squared for friction velocities between proposed equation and friction velocity formula analyzed 0.999 to 1.000 in a very good agreement with each equation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1676-1681
• /
• 2003

The attachment of mobile vehicle is necessary for the automated operation on the inclined or vertical walls of steel structures. Since the vehicle requires attaching devices additionally, its overall efficiency can be reduced by the devices. Therefore, external shapes of mobile vehicles have to be researched to give the effective movement on the vertical face. For the design of mobile vehicle, the guideline has been derived from the modeling of wall-climbing, so that the vehicle should have a specific external shape for vertical movement due to the gravitational force. Hence, some adequate arrangement of attaching device to the mobile vehicle has been presented for the effective movement. In the experiments with four permanent magnetic wheels, a plausible result was achieved as a vertical attaching force of 185.2(N), a friction force of 153.8(N) and a curvature radius of 1.4m. The mobile vehicle should be modified according to the proposed design guideline. and then it could be applied to a specific operation as an appropriate external shape. Also, Further research is recommended on an optimal posture and a moving method in a specific application. as the attaching force ortho vehicle can be affected by its posture.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.9
• /
• pp.77-84
• /
• 2004

The attachment of mobile vehicle is necessary for the automated operation on the inclined or vertical walls of steel structures. Since the vehicle requires attaching devices additionally, its overall efficiency can be reduced by the devices. Therefore, external shapes of mobile vehicles have to be researched to give the effective movement on the vertical face. For the design of mobile vehicle, the guideline has been derived from the modeling of wall-climbing, so that the vehicle should have a specific external shape for vertical movement due to the gravitational force. Hence, some adequate arrangement of attaching device to the mobile vehicle has been presented for the effective movement. In the experiments with four permanent magnetic wheels, a plausible result was achieved as a vertical attaching force of 185.2(N), a friction force of 153.8(N) and a curvature radius of 1.4m. The mobile vehicle should be modified according to the proposed design guideline, and then it could be applied to a specific operation as an appropriate external shape. Also, Further research is recommended on an optimal posture and a moving method in a specific application, as the attaching force of the vehicle can be affected by its posture.