• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.6
• /
• pp.645-654
• /
• 2011

Temporal supports is proposed for the large block construction of a double-deck truss girder of a bundle type cable-stayed bridge. The design force of the temporal bents cannot be evaluated by a conventional design procedure with gust factored static wind loads. The uplift forces in BS5400 also can not estimate the design forces of the temporal bents properly for the turbulent wind loads. A frequency-domain buffeting analysis is performed to evaluate the design forces of the temporal bents considering the interactions between the girder and temporal supports. Two cases of modeling are compared to estimate the stiffness contribution of temporal supports in determining design forces, i.e., an analysis model including temporal bents in the structural analysis modeling and an analysis model with fixed supports at the bent tops neglecting the stiffness of temporal bents. The consideration of bent stiffness usually generates smaller reaction forces than rigid support modeling. Consequently, the effectiveness and usefulness of the buffeting analysis procedure with full modeling of temporal supports are demonstrated for the design of a temporal bents of the construction of a bundle type cable-stayed bridge.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.4
• /
• pp.69-75
• /
• 2009

The load distribution and deformation of pile-bent structures are investigated using a numerical study. A numerical analysis that takes into account the effects of varying cross-sectional area was performed for different pier diameters, loading steps, and soil conditions. Through the comparison study, it is shown that the location of maximum bending moment is almost the same per each loading step, regardless of varying cross-sections. However, the member force (i.e., stress of pile material) has the largest value at the ground surface when the cross-section is changed. Based on the results obtained, it is found that the location of maximum member force influences highly the behavior of pile-bent structure with varying cross-sections for repair works.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.5
• /
• pp.45-53
• /
• 2017

IPM bridge was developed to revise the problems of IAB bridge by Nam et al, (2016). This research conducted the p-y analysis to examine the parameter traits among the protruded length (H), penetrated length (L) of pile bent and soil conditions. From the results, the maximum bending moment happened in the top segment of pile bent, because it is integrated to the upper structure. Also, the maximum shear force was shown in the boundary of the sand and weathered soil zones according to the analysis soil conditions. The maximum member force and unbraced length is converged when the ratio (L/H) of protruded length (H) and penetrated length (L) is 1.0. The larger material force is happened, if the pile bent is penetrated shallowly compared to the protruded length. The definite inflection points were shown in the horizontal displacement curve from the p-y analysis, also the smaller penetrated length made the curve grade slower.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.33-39
• /
• 2008

To improve the mixing efficiency and to reduce the pressure loss, it is needed to develope a new mixing device for supersonic combustion. The vent mixer is introduced as the new supersonic fuel-air mixer. Computational analyses, that include pressure profile, density contour, and streamline tracing, have been carried out. The expansion wave generates at the end of the extended upper wall of the mixer. And it reduces the shock wave from the hole. Incoming air flow through the hole makes several recirculation regions which increase the mixing efficiency, and the separation region at the downward wall expends the boundary layer which reduces the pressure loss.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.5
• /
• pp.538-542
• /
• 2018

Echo generated in digital hearing aid vent give rise to user's discomfort. For cancelling feedback echo in vent, it is required to estimate vent impulse response exactly. The vent impulse response has time varying and sparse characteristics. The IPNLMS has been known a useful adaptive algorithm to estimate vent impulse response with these characteristics. In this paper, subband sparse adaptive filter which applying IPNLMS to subband hearing aid structure is proposed to cancel echo of vent by estimating sparse vent impulse response. In the propose method, the decomposition of input signal to subband can pre-whiten each subband signal, so adaptive filter convergence speed can be improved. And the poly phase component decomposition of adaptive filter increases sparsity of each components, and the better echo cancellation can be possible without additional computation. To derive coefficients update equation of the adaptive filter, by defining the cost function based weight NLMS is defined, and the coefficient update equation of each subband is derived. For verifying performances of the adaptive filter, convergence speed, and steady state error by white signal input, and echo cancelling results by real speech input are evaluated by comparing conventional adaptive filters.

• Applied Chemistry for Engineering
• /
• v.26 no.3
• /
• pp.275-279
• /
• 2015

Poly(3,4-ethylenedioxythiophene) : poly(styrenesulfonate) (PEDOT : PSS) has attracted a great deal of attention as a transparent conductive material for organic solar cells or organic light-emitting diodes due to its high electrical conductivity, optical transparency, and excellent mechanical flexibility. It is well known that a solvent doping for PEDOT : PSS thin-films significantly increases the conductivity of films. In this paper, the effect of various kinds of solvent doping and post-treatment on the electrical and structural properties of PEDOT : PSS thin-films is investigated. The solvent doping greatly increases the conductivity of PEDOT : PSS thin-films up to 884 S/cm. A further enhancement of the conductivity of PEDOT : PSS thin-films is achieved by the solvent post-treatment which raises the conductivity up to 1131 S/cm. The enhancement is mainly caused by the depletion of insulating PSS and forming conducting PEDOT-rich granular networks. Strong optical absorption peaks at the wavelength of 225 nm of PEDOT : PSS thin-films indicate the depletion of insulating PSS by post-treatment. We believe that the solvent post-treatment is a promising method to achieve highly conductive transparent PEDOT : PSS thin-films for applications in efficient, low-cost and flexible organic devices.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.457-463
• /
• 2005

In the present work, the design of fuel system for Smart UAV focused on the main components such as fuel feed system, fuel tank vent system, and refueling system was conducted. Based on the previous conceptual design results, the size of the component was calculated with refined airframe structure data and accurate engine data. It was verified that the design requirements for the feed system, vent system, and refueling system were satisfied.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.19 no.2
• /
• pp.7-13
• /
• 1982

In this Paper, the radiation Patterns of long wire antennas are computed by applying Dyadic Green's Function to the propagation vector, This result is used to analyze the polarized radiation patterns for the various geometrical structures of the bent dipole antennas. When the ratio of the vertical portion over the total length of the bent dipole antenna is 0.4major angle and axail ratio are changed most sensitively for the azimuth rotation, and the radiation field propagates strongly perpendicular to the bent antenna plane.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.68.1-68
• /
• 2002

• Journal of Auto-vehicle Safety Association
• /
• v.11 no.1
• /
• pp.23-29
• /
• 2019

Recently, use of composite materials has been increasing for body structures and chassis parts in the car industry because of weight reduction effect and excellent mechanical thermal characteristics. However, application of composite materials in brake system is very difficult because it is hard to obtain enough brake performance due to low heat storage capacity of the composite materials. In this paper, we will present new carbon ceramic composite disc with high flow characteristic. To obtain this characteristic, new vent structures were designed by using ARIZ method and substance-field model analysis. The flow effect of these vent structures on the brake performance was verified by pugh matrix and cooling test. The test results show improvement of cooling performance up to $30^{\circ}C$. Finally, These results will improve brake the reliability of the brake performance for the high performance vehicles and electric vehicles.