• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.259-260
• /
• 2011

본 논문은 벅-부스트 컨버터의 듀티비 제어를 통해 풍력발전시스템이 최대 효율을 갖도록 MPPT (Maximum power point tracking) 알고리즘을 구현하고, 발전된 전력을 계통으로 전달하기 위한 인버터 제어방법 및 시스템 구성을 제안한다. 특히 풍속정보와 발전기 속도를 제거하여 센서로 인한 단점들을 배제하였고, 제안한 풍력발전시스템과 알고리즘의 유용성을 시뮬레이션을 통해 검증한다.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.277-278
• /
• 2013

본 논문은 인터리브드 기법을 적용한 양방향 DC-DC 컨버터의 구현 및 실험에 대해 서술하였으며 구현한 컨버터의 특성을 분석하였다. 구현한 컨버터는 변압기를 사용하여 절연효과를 가지고 있으며 벅/부스트 구조가 적용되어 비교적 낮은 권선비로도 높은 승압과 강압이 가능하다. 또한 인터리브드 기법을 적용하여 리플전류의 감소효과를 가지고 있다. 각 모드별로 컨버터의 특성을 분석하였으며 벅모드와 부스트모드에 대한 동작은 실험을 통하여 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.172-173
• /
• 2017

본 논문은 벅 차동전력조절 회로가 적용 된 다출력 스위치드-커패시터 부스트 컨버터의 소신호 모델 분석에 대한 논문이다. 제안하는 회로는 각 태양광 모듈의 최대전력점을 추정하기 위해서 제어된다. 제안하는 회로는 상태 공간 평균화 기법과 시그널 플로우 그래프를 통해서 해석하였으며 PSIM과 MATLAB을 통해서 증명하였다.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.115-116
• /
• 2012

본 논문은 벅 컨버터를 이용하여 배터리를 충전할 때의 특성을 이용하여 과도상태의 응답속도의 개선을 하지 않고 수식을 간소화 시키면서 배터리 충전시에 전달함수를 보다 쉽게 적용할 수 있도록 등가화시켜 배터리 충전을 수행하였다.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.489-490
• /
• 2019

본 연구에서는 태양광 벅 컨버터 제어기에 P&O 알고리즘을 이용하면서 MPPT 알고리즘의 추적 속도를 올리기 위한 최적 태양전지 전압 제어기 설계방법에 대해 제안한다. 제안된 제어기에서는 외부 루프의 MPPT 제어기의 수행 속도를 얼마나 빠르게 하는지에 대한 이론적인 방법을 제시하고 업데이트 주기를 0.1[sec] 이하로 줄이는 것을 목표로 전압제어기는 오버슈트가 업고, 빠른 상승시간을 갖도록 설계하여 MPPT 제어기의 추적 속도를 향상시키는 제어기법을 제안하고, 설계된 제어기 이득을 PSIM 시뮬레이션을 통해 제어기 성능을 검증한다.

• Journal of IKEEE
• /
• v.15 no.2
• /
• pp.134-142
• /
• 2011

This paper describes a tripple-mode high-efficiency DC-DC buck converter. The DC-DC buck converter operate in PWM(Pulse Width Modulation) mode at moderate to heavy loads(100mA~500mA), in PFM(Pulse Frequency Modulation)at light loads(1mA~100mA), and in LDO(Low Drop Out) mode at the sleep mode(<1mA). In PFM mode DPSS(Dynamic Partial Shutdown Strategy) is also employed to increase the efficiency at light loads. The triple-mode converter can thus achieve high efficiencies over wide load current range. The proposed DC-DC converter is designed in a CMOS 0.18um technology. It has a maximum power efficiency of 96.4% and maximum output current of 500mA. The input and output voltages are 3.3V and 2.5V, respectively. The chip size is 1.15mm ${\times}$ 1.10mm including pads.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.1
• /
• pp.57-63
• /
• 2012

In this paper, a switch sizing method is proposed in order to prevent the cross-regulation in the TM type SIDO DC-DC buck converter. In TM type SIDO DC-DC buck converter, a DCM operation is required. In the DCM operation, the inductor peak current is larger than that in the CCM. Because of the larger inductor peak current and the added switch resistance, the voltage drop is increased, resulting in possible cross-regulation. To solve this problem, the switch resistance must be considered in sizing the switch. To simplify the calculation of the resistance, the inductor current was replaced by the average load current. Using the proposed method, TM type SIDO DC-DC buck converter for camera module was designed to provide two independent supply voltage(2.8 V and 1.8 V). The designed circuit was fabricated in a standard $0.35{\mu}m$ CMOS process. At a switching frequency of 1 MHz and a load current of 200 mA, a power effciency of 80.7% was achieved.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.398-401
• /
• 2011

This paper presents a high-efficiency CMOS PWM DC-DC buck converter. It generates a constant output voltage(1-2.8V), from an input voltage(3.4-3.9V). Inductor-based type is chosen and inductor current is controlled with PWM operation. The designed circuit consists of power switch, Pulse Width Generation, Buffer, Zero Current Sensing, Current Sensing Circuit, Clock & Ramp generation, V-I Converter, Soft Start, Compensator and Modulator. Switching Frequency is 1MHz, It operates in CCM when the load current is more than 40mA, and the maximum efficiency is 98.71% at 100mA. Output voltage ripple is 0.98mV(input voltage:3.5V, output voltage:2.5V). The performance of the designed circuit has been verified through extensive simulation using a CMOS $0.18{\mu}m$ technology.

• Journal of IKEEE
• /
• v.18 no.3
• /
• pp.320-327
• /
• 2014

Recently, Importance of power management circuit technology is increased with the development of portable electric devices. This paper presents a high performance DC-DC buck converter for mobile applications. Especially, presented design have low ripple voltages and driving capability of large load current. A designed voltage mode 2-phase DC-DC converter is implemented in a $0.35{\mu}m$ CMOS process, and the overall size is $2.35{\times}2.35mm^2$. The peak efficiency is 91% with a 4MHz frequency and the maximum load current is 4A.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.314-317
• /
• 2016

Recently, efforts to maximize battery life in progress with an increase in the demand for portable devices. In this paper, we propose multi-phase buck converter with fast transient response. Multi-phase buck converter may be used for the output capacitor of small size because the ripple cancellation effect, it is possible to use an inductor having an inductance less. The portable device for quick change from standby mode to active 4-phase design structure was given a fast transient response. The proposed multi-phase buck converter was fabricated using a 0.18 um CMOS process and the supply voltage ranges from 2.7V to 3.3V, the maximum load current is 500mA and settling time is 10us.