• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.1220-1226
• /
• 2007

As the industry of 21C has been developed, the gas industry has grown and it has not only the convenience but also the riskiness fer using. Especially, the energy and environment problems have been getting serious after the modern industry revolution. Therefore, the demand of gas as an eco-friendly energy source is getting increased. With the demand of gas, the installation and use of gas boiler is also increased, so human life injury by the waste gas(CO) of boiler goes on increasing every year. Therefore, we want to find out the harm to human body through the study on the concentration of CO by the length of the curved exhaust tube of boiler. The allowable concentration of CO is 50ppm. The length of the one-meter-three-curved tube after three minutes is applicable to 50ppm of the threshold limit values of CO. Also, five meters exceed the threshold limit values of CO after five minutes. Strangely, the concentration of CO is under the threshold limit values from two to four meters.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.1
• /
• pp.67-73
• /
• 2011

The purpose of this study is to investigate experimentally the spray-atomization and combustion-emission characteristics of biodiesel-DME blended fuel. In this study, two types of test fuels pure biodiesel (BD100) and blended fuel (B-DME20) were used, and the spray and combustion characteristics of different fuel compositions were analyzed. DME constitutes 20% and biodiesel constitutes 80% (by mass fraction) of the blended fuel. The overall spray characteristics, spray tip penetration, and cone angle were evaluated using frozen spray images. In addition, the combustion and emission characteristics were analyzed on the basis of the evaluated data for a single-cylinder CI engine with common-rail injection system. It was revealed that the injection profiles of both the test fuels for a given injection pressure showed similar trends. However, the injection profiles of the blended fuel (B-DME20) indicated shorter ignition delay than those of biodiesel.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.692-698
• /
• 2020

This paper examines the effects of a multi-stage pilot split injection strategy on combustion and exhaust emission factors in a single-cylinder diesel engine. One analysis noted that in the single-injection condition, the maximum in-cylinder pressure and rate of heat release were highest. The pilot injection quantity was evenly divided, showing a tendency to decrease as the number of injections increased. In another injection condition, when the multi-stage pilot split injection strategy was applied, IMEP, engine torque, and combustion increased. The COV_IMEP was greatest with the lowest combustion efficiency. The combustion ability was poor. In a single injection condition, the O₂ concentration in the exhaust gas was the lowest and the CO₂ was the highest. When the multi-stage split injection strategy was applied, the low temperature combustion process proceeded, and the oxidation rate of CO₂ decreased while the emission level increased. In a single injection condition in which a locally rich mixture was formed, the HC emission level showed the highest results. A 55.6% reduction of NOx emission occurred under a three-stage pilot injection condition while conducting a multi-stage pilot split injection strategy.

• Journal of Energy Engineering
• /
• v.14 no.3 s.43
• /
• pp.173-179
• /
• 2005

Fuel injection system has more benefits in power, fuel consumption and emission than carburetor system even in high speed small engine. Up to date fuel injection system is used in motor car but is not used in motorcycles in Korea. EFI (Electronic fuel injection) system which has ECU can control precise fuel supply to variable RPM in engine. The purpose of this study is the investigation of effects of fuel injection system to improve the engine performance and efficiency in variable revolution of high speed small engine which is 4 Valves SOHC single cylinder engine used in motorcycle.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1359-1365
• /
• 2011

The purpose of this study is to investigate the effect of ethanol content on the emission of nanosized particles from a diesel-ethanol blended fuel engine. The engine combustion and exhaust emission characteristics of a singlecylinder diesel engine were analyzed using an emission analyzer and an SMPS(scanning mobility particle sizer). The analysis revealed that soot emission increased with the ignition delay. When the ignition delay was fixed, an increase in the ethanol content caused a decrease in the soot emission. With an increase in the ethanol blending ratio, the number concentration and mass distribution of nanosized particles generally decreased. However, for 30% ethanol blending, large particles were observed because of the agglomeration of soot particles, and consequently, the particle mass increased.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.1
• /
• pp.24-34
• /
• 1985

The study of unsteady gas exchange processes in the inlet and exhaust systems of the single-cylinder 4-stroke cycle spark ignition engine is presented in this paper. The generalized method of characteristics including friction, heat transfer, change of flow area and entropy gradients was used for solving the equations defining the gas exchange process. The path line calculation was also conducted to allow for calculation of the gas composition and entropy change along the path lines, and of the variable specific heat due to the change of temperature and composition. As the result of the simulation, the properties at each point in the inlet and exhaust pipe, pressure and temperature in the cylinder, and charging efficiency were obtained. Pumping loss and residual gas fraction were also computed. The effect of engine speed, exhaust and inlet pipe length on the pumping loss and charging efficiency were studied showing that the results were in agreement with what has been known from experiments.

• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.58-67
• /
• 1984

공간적 화염전파에 대한 실험적인 파악을 통하여 오토엔진에서의 연소과정과 진행을 위한 깊은 통찰을 할 수 있다. 그것을 통하면 매우 희박한 공기, 연료 혼합기의 경우 실린더에서 직접소염 과정을 확인할 수도 있고 hydrocarbon의 불완전 연소와 나타나는 qunching zone간의 관계를 조사할 수도 있다. 광전도 섬유기술(Lichtleit-fasertechnik)을 사용하여 새로 개발된 측정방법을 이용하여 단기통 오토엔진에서 화염면의 공간적인 전파과정과 매우 희박한 공기 연료 혼합기 에서의 quench zone의 출현을 조사하였다. 측정결과들은 공기연료 혼합기가 희박해 질수록 화 염전파 과정이 점점 느려지는 것을 보여준다. 아주 높은 공기 과잉율을 갖는 엔진 운전에서는 화염속도와 연소속도가 매우 급하게 감소한다. 그리하여 화염면은 팽창 단계에서 상대적으로 증가하는 피스톤속도 때문에 더이상 피스톤을 따를 수가 없으며 그로 인해 직접 피스톤상부에 소염대가 형성된다. 그에 의해 배기가스에서의 hydrocarbon 방출의 급격한 증가와 효율이 급격히 감소하는 엔진 운전과 관련이 지어진다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.79-85
• /
• 2009

Low temperature combustion regime for the simultaneous reduction of nitrogen oxides ($NO_x$) and paticulate matter (PM) is demonstrated in single cylinder engine at various operating parameters, such as EGR rate, injection timing, EGR temperature, amount of fuel and swirl rate. Low temperature combustion is accomplished by high exhaust gas recirculation (EGR) rate in this study. Generally, the emission of $NO_x$ almost completely disappears and PM significantly increases in the first decreasing regime of oxygen concentration but after peaking about 10~12% oxygen concentration, PM then decreases regardless of fuel injection quantity. Low temperature combustion regime was extended by low EGR temperature, high injection pressure and low amount of fuel.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 1999.10a
• /
• pp.213-214
• /
• 1999

발전소, 소각시설 및 산업공정에서 다량으로 배출되는 질소산화물(NOx)을 처리하기 위하여 과잉공기 연소시 고온에서 암모니아(NH$_3$)나 요소(CO(NH$_2$)$_2$)를 환원제로 사용하는 SNCR법, 그리고 암모니아와 각종 촉매를 사용하여 NOx를 $N_2$로 환원시키는 SCR법이 주로 개발ㆍ상용화되었다. 최근 90년대 초반부터 NOx의 제거기술은 Cu-ZSM-5, Alumina 통의 경제적이고 효과적인 촉매의 개발과 암모니아 사용으로 인한 부담요소를 제거하고자 다양한 HCs를 대체사용하는 방향으로 많은 연구가 진행되었다.(중략)

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2007.06a
• /
• pp.297-300
• /
• 2007

There have been 3E problems of energy, economy and environment since the earth has its history. Especially, the energy and environment problems have been getting serious after the modern industry revolution. Therefore, the demand of gas as an eco-friendly energy source is getting increased. With the demand of gas, the installation and use of gas boiler is also increased, so human life injury by the waste gas(CO) of boiler goes on increasing every year. It is the content about a life of the exhaust tube which is used at Gas boiler in this paper. We explain also the course to apply the 6SC(6 Step Creativity) of practical TRIZ and evaluate the re solution.