• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.583-586
• /
• 2017

Infrared signal measurement are conducted from a micro-turbo jet engine with different nozzle configurations. The conventional cone type, a S-shaped type with aspect ratio 5.2 and five rectangular type nozzle with different aspect ratios are used for this experiment work. The result show that infrared signal from the exhaust gas decrease as the aspect ratio increase. In case of S-shaped nozzle, the maximum infrared signal is reduced about 28.4% when compared of rectangular nozzle with aspect ratio 5(AR5).

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.5
• /
• pp.1-8
• /
• 2016

Micro turbojet engine test and infrared signal measurement were conducted to understand the characteristics of the engine performance and infrared signal with the variants of the exhaust nozzle configuration. A cone type nozzle and five rectangle type nozzles which has aspect ratio from one to five were used for the experimental work. The results show that there are not much difference between cone and rectangle nozzles of the thrust and specific fuel consumption. However infrared signal from exhaust gas become smaller as increasing aspect ratio.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.12
• /
• pp.967-972
• /
• 2013

A MILD (Moderate and Intense Low oxygen Dilution) combustion, which is effective in the reduction of NOx, is considerably affected by the recirculation flow rate of hot exhaust gas to the combustion furnace. The present study used the MILD combustor, which has coaxial cylindrical tube. The outside tube of the MILD combustor corresponds to the exhaust gas passage and the inner side tube is the furnace passage. A numerical analysis was accomplished to elucidate the characteristics of exhaust gas entrainment toward the inner furnace with the changes of coanda nozzle geometrical parameters, nozzle passage gap length, nozzle passage length, nozzle angle and expansion length. The optimal configuration of coanda nozzle for the best entrainment flow rate was gap length, 0.5 mm, expansion angle, 4o and expansion length, 146 mm. The nozzle passage length was irrelevant to the exhaust gas entrainement.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.45-45
• /
• 2010

반도체 및 디스플레이 산업에 사용되는 진공펌프의 효율이 증대됨에 따른 성능 평가 기술의 향상 과 미세 유량을 조절 및 측정할 수 있는 시스템의 개발이 요구되고 있다. 유량 시스템 중 소닉노즐은 기체 유량 측정 표준기로 사용되고 있다. 또한 유량 측정에 있어서 사용상의 편리성, 이동성, 재현성 등 여러 가지의 장점을 가지고 있어 산업 현장에서 많이 사용되고 있다. 본 연구는 소닉노즐을 넓은 유량 범위에서 사용할 수 있도록 소닉노즐의 유출계수 교정을 목적으로 한다. ISO 9300에서 제시한 사양에 맞추어 목 직경 0.03 mm와 0.2 mm 그리고 1.6 mm의 소닉노즐을 제작하였다. 한국표준과학연구원에서 진공용 유량측정 장치로 개발된 정적형 유량계를 이용하여 제작된 3 종의 소닉노즐 유출계수를 확장불확도 3% 이내로 교정하였다. 교정된 소닉노즐의 유량 측정범위는 약 0.6~90, 000 cc/min 범위를 갖는 것으로 나타났으며, 사용유동 조건에 해당되는 레이놀드 수(Reynolds number) 범위는 26~75, 700 으로 확인되었다. 이러한 결과는 교정된 소닉노즐을 이용하여 진공공정에서 필요한 극 미세 유량의 정밀측정을 가능하게한 새로운 연구결과로 판단된다. 교정된 소닉노즐을 이용하여 진공펌프의 배기속도 측정결과는 기 구축된 정적법을 이용한 배기속도 측정결과와 3% 이내의 오차범위내로 매우 잘 일치함을 보였다. 교정된 소닉노즐은 향후 반도체 및 디스플레이 공정에 사용되는 다양한 진공펌프들의 배기속도를 현장에서 간단하게 평가할 수 있는 '현장 성능평가 장치'에 활용할 예정이며, 현재 공정현장에서 배기속도 측정에 널리 사용 중인 MFC를 대체할 수 있을 것으로 예상된다.

• Journal of Energy Engineering
• /
• v.22 no.4
• /
• pp.413-419
• /
• 2013

The present study used the MILD combustor, which has coaxial cylindrical tube. The outside tube of the MILD combustor corresponds to the exhaust gas passage and the inner side tube is the furnace passage. A numerical analysis was accomplished to elucidate the characteristics of exhaust gas entrainment toward the inner furnace with the changes of venturi nozzle geometrical parameters, nozzle position, nozzle gap between high pressure air nozzle and venturi nozzle, and with the change of high pressure nozzle inlet velocity. The entrainment flow rate for the case with the high pressure air nozzle attached at the exhaust gas wall has relatively small change with the change of nozzle gap. That for the case with the high pressure air nozzle exposed to the exhaust gas has monotonically increase with the change of nozzle gap. The flow rate ratio of entrainment flow rate has considerably increase tendency with relatively lower air inlet velocity, on the other hand, that with relatively higher air inlet velocity could be seen relatively small increase.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2016.05a
• /
• pp.88-89
• /
• 2016

선택적 환원 촉매(SCR : Selective Catalytic Reduction) 시스템은 대기오염을 예방하기 위한 배기가스 처리장치 중 하나이다. 본 연구에서는 전산유체역학(CFD : Computational Fluid Dynamics)를 사용하여 SCR 시스템 의 효율향상을 위하여 ANSYS-CFX package를 이용하여 점성 유동 해석을 수행하였다. SCR 시스템의 점성 유동 흐름의 전산 유체 역학을 이용하여 시뮬레이션하기 위하여 Navier-Stokes 방정식을 지배방정식으로 사용하였다. CATIA V5를 사용하여 SCR 시스템의 형상을 3D 모델링을 하였고, 암모니아와 배기가스의 혼합 비율을 확인하기 위해 요소수 분사 노즐의 위치를 변경하였다. 요소수 분사 노즐은 배기관의 입구로부터 1/3, 1/2, 2/3에 위치한다. 또한, 분사 노즐의 위치가 배기관 입구의 1/3에 위치할 때 노즐의 분사구수에 따른 효율을 확인하기 위하여 분사구수를 4Hole, 6Hole, 8Hole일 경우를 확인하여 비교하였다. 시뮬레이션의 결과로는 배기관 입구에 가까울수록, 분사구수가 많을수록 효율이 좋아짐을 확인하였다.

• Journal of the Korean Institute of Gas
• /
• v.21 no.3
• /
• pp.53-60
• /
• 2017

Various researches have been conducted for the reduction of NOx at the combustion furnace and exhaust gas recirculation method is commonly used technology for NOx reduction. The present research adopted coanda nozzles at the outside pipes of furnace to entrain the exhaust gas for the exhaust gas recirculation and the mixed gas was ejected to the tangential direction to cause the swirl flow in the furnace. The combustion flow characteristics in the exhaust gas recirculation burner with coanda nozzle has been elucidated by analyzing the swirl flow streamlines, temepraure and reaction rate distribution in the furnace. The exhaust gas entrained flow rate has been investigated by changing the excess air factor and coanda nozzle gap and the exhaust gas entrained flow rate increased with the increase of excess air factor and it decreased with the increase of coanda nozzle gap. The mean temperature at the exit plane of exhaust gas decreased with the excess air factor and it was little affected by the increase of coanda nozzle gap. The NOx mass fraction at the exhaust gas exit plane remarkably decreased with the excess air factor and it was also little affected by the increase of coanda nozzle gap.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.2
• /
• pp.103-108
• /
• 2012

A MILD (Moderate and Intense Low oxygen Dilution) combustor decreases NOx formation effectively during the combustion process and NOx formation is affected significantly by the exhaust gas entrainment rate toward fuel and air. The present study focused on the new MILD combustor, which has coaxial cylindrical tube. The outside tube of the new MILD combustor corresponds to the exhaust gas passage and the inner side tube is the furnace passage. The connection pipe is set between the outer side and the inner side tubes and coaxial air nozzle is inserted at the center of the connection pipe. A numerical analysis is accomplished to elucidate the characteristics of exhaust gas entrainment toward the inner furnace with the changes of air nozzle exit velocity, nozzle diameter, nozzle exit position and exhaust gas side pressure. The entrainment rate is proportional to the square root of air nozzle exit velocity and negatively proportional to the pressure difference between the exhaust gas side and furnace side pressures. The effect of air nozzle exit position is not considerable on the exhaust gas entrainment.

• Journal of the Korean Institute of Gas
• /
• v.23 no.3
• /
• pp.1-6
• /
• 2019

The purpose of the present study is to elucidate flue gas recirculation device for reduction of nitrogen oxides using coanda nozzle without adopting additional power driving fan in a waste incinerator. The characteristics of the exhaust gas recirculation flow rate and the average temperature change at the outlet of the mixed gas were investigated according to the change of air supply nozzle gap and the position of air supply nozzle. When the gap of the air supply nozzle was changed to 3.22, 4.03, and 4.84 mm, the largest recirculation flow ratio, which is the ratio of exhaust gas recirculation flow rate and air supply flow rate, was 2.227 for the case with 3.22 mm and its mean temperature at outlet was $594.8^{\circ}C$. When the position of the air supply nozzle changes to the front position, neck position, and expansion position of the coanda nozzle neck, the recirculation flow ratios at the forward position and the neck position were nearly almost the same value, 1.843, and 1.696 at the expansion position, their mean temperatures were $559.8^{\circ}C$ and $544.3^{\circ}C$, respectively.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.152-158
• /
• 2016

Nitrogen oxide is generated by the chemical reaction of oxygen and nitrogen in higher temperature environment of combustion facilities. The NOx reduction equipment is generally used in the power plant or incineration plant and it causes enormous cost for the construction and maintenance. The flue gas recirculation method is commonly adopted for the reduction of NOx formation in the combustion facilities. In the present study, the computational fluid dynamic analysis was accomplished to elucidated the cold flow characteristics in the flue gas recirculation burner with coanda nozzles in the flue gas recirculation pipe. The inlet and outlet of flue gas recirculation pipes are directed toward the tangential direction of circular burner not toward the center of burner. The swirling flow is formed in the burner and it causes the reverse flow in the burner. The ratio of flue gas recirculation flow rate with the air flow rate was about 2.5 for the case with the coanda nozzle gap, 0.5mm and it was 1.5 for the case with the gap, 1.0mm. With the same coanda nozzle gap, the flue gas recirculation flow rate ratio had a little increase when the air flow rate changes from 1.1 to 2.2 times of ideal air flow rate.