• Geotechnical Engineering
• /
• v.9 no.4
• /
• pp.65-82
• /
• 1993

A series of torsion shear tests were performed to study the drained stress -strain behavior of medium dense Santa Monica Beach sand under various stress paths. The torque was applied to both clockwise and counterclockwise directions at the end of hollow cylinder specimen. Two clip gages had been previously used to measure the changes in wall thickness and diameter of the specimen. In this study, however, the lateral strain was determined by measuring volume changes in specimen. Specimens were prepared by the air pluviation method and gaseous carbon deozide( CO2) was used to measure precisely volumetric strain in specimen. The drained stress -strain behavior of cohesionless Boils during rotation of principal stress directions was analysed based on the results of torsion shear tests. The coupling of mal stress were applied. It was also found from the test results that the atrial strain at failure decreased with increasing value.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.1
• /
• pp.126-132
• /
• 1999

This article describes the use of an activator with anterior high pull headgear to treat a skeletal Class II malocclusion in children in the mixed-dentition phase. A combination of headgear-activator appliance can inhibit forward and downward growth of the maxillary complex while stimulating mandibular growth. The correction of Class II malocclusion can be achieved by careful case selection of a motivated patient with a favorable growth pattern. The patients who have skeletal Class II malocclusions were treated by means of activator with anterior high pull headgear and the following results were observed; 1. Forward and downward growth of the maxillary complex were inhibited 2. Mandibular growth was stimulated and counterclockwise rotation of the mandible was observed. 3. Large overjet and deep overbite were corrected.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.105-114
• /
• 1993

The ciculation due to bottom density current produced by a dense inflow into a small reservoir is analysed by numerical scheme. Before the front of the density current arrives at the downstream end, the mixing in the reservoir is mainly caused by the anticlockwise vortex formed at the downstream of plunging point along the movement of bottom density current. Upon the arrival of the front of the density current at the downstream end an internal surge is created through an internal hydraulic jump. With repeated propagation of the internal surge back and forth the mixing in the reservoir is progressed and the thickness of dense layer is increased upward. The dilution of the overflow at downstream end is found to depend on inflow densimetric Froude number, reservoir length and elapsed time. The time required for the overflow to attain a specified dilution increases as reservoir length increases and Fre decreases.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.3
• /
• pp.270-278
• /
• 2009

Friction stir welding is a relatively new solid state joining process. A6061-T6 and A5052-H32 aluminium alloy has gathered wide acceptance in the fabrication of light weight structures requiring a high strength to weight ratio and good corrosion resistance. This friction stir process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters such as tool rotational speed, welding speed, etc., and tool pin profile play a major role in deciding FSP zone formation in A6061-T6 and A5052-H32 aluminium alloy. Three different tool pin profiles have been used to fabricate the dissimilar butt joints. The formation of friction stir processed zone has been analysed macroscopically. Tensile properties of the joints have been evaluated and correlated with the friction stir processed zone formation.

• 한국해양학회지
• /
• v.30 no.3
• /
• pp.227-236
• /
• 1995

A simple layer model based on isophcnal coordinate is applied to the East Sea to examine the dynamics of circulation. The results confirm the existing knowledge about role of inflow-outflow and wind in driving the circulation. It is found, however, that the buoyancy flux generates quite different circulation pattern; it enhances the inflow-outflow driven circulation and has a convective nature. The circulation considering all these effects resembles the schematic one presently known. In the circulation, the intermediate layer is outcropped in the north off the northern boundary, ventilated here and flows cyclonically in the northern part of basin. This water, however, does not flow southward directly because of the strong eastward (separating from the coast) current in the layer above. This water also loses its potential vorticity while traveling around the periphery of the outcropping region and is thus characterized by minimum potential vorticity in the interior of the basin.

• 한국해양학회지
• /
• v.24 no.2
• /
• pp.96-108
• /
• 1989

Applying the numerical scheme developed by Semtner (1974), we investigate the circulation system in the Japan Sea in response to the air-sea interaction and the wind. In spite of blocking straits, resulting surface circulation pattern is similar to the schematic surface current chart introduced by Uda(1934) and Naganuma (1972); the northward flow along the Korean coast and the anticlockwise gyre in the northeastern part of the Japan Sea. Also the southward current flows along the Korean coast at depth of 100-200 m as similar to the North Korean Cold Current suggested by Kim and Kim (1983). And the sinking phenomenon of relatively saline water in the northeastern part of the Japan Sea is similar to the formation of the Japan Sea Proper Water.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.11 no.2
• /
• pp.37-48
• /
• 2006

HF radar-derived current data obtained in 2002 and 2004 are analyzed to examine the effects of the completion of the Saemangeum 4th tidal dyke in June 2003, connecting Gogunsan-Gundo and Bieung-Do, on the coastal surface $M_2$ current pattern. Comparison between the currents by HF radar and current meter mooring showed good agreements. Counterclockwise rotation of the $M_2$ current in the observed area did not change with the dyke construction. Strong westward ebb jet from the gap of the dyke was observed in 2002 but disappeared in 2004. The complete closing of the dyke gap caused the current speed increase around the mouth of the Kem River estuary, decrease around Gogunsan-Gundo and the dyke, the changes in the direction of maximum current to north-ward from eastward and the delay of the maximum flood current occurrence around Gogunsan-Gundo and the dyke. Around Yeon-Do, the maximum flood current directed more clockwise and occurred rather earlier. These changes of the $M_2$ current ellipse characteristics imply that the effects of the dyke construction reached the area connecting Mal-Do and Yeun-Do.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.1
• /
• pp.76-83
• /
• 2010

The Characteristics of the flow field through cylinders with in-line and staggered arrangements were calculated by vortex method. Vortex distributions and velocity profiles around the cylinders with in-line and staggered arrangements were simulated at the pitch ratio of Pt/D=1.25~2.0 and Reynolds number of Re=$4.0{\times}10^1{\sim}4.0{\times}10^4$. As the results the vortices of clockwise at the upper separation point cylinder and the vortices of anticlockwise at the lower separation point of each cylinder were generated at both in-line and staggered arrangements. The generation of the reverse flow in the rear region of the cylinders was caused by the pitch ratio and Reynolds number, the boundary region was at the pitch ratio of Pt/D=1.5 and Reynolds number of Re=$4.0{\times}10^2{\sim}4.0{\times}10^3$ in case of in-line arrangement and was at the pitch ratio of Pt/D=1.4 and Reynolds number of Re=$4.0{\times}10^1{\sim}4.0{\times}10^2$ in case of staggered arrangement.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.9 no.4
• /
• pp.194-200
• /
• 1997

A two-dimensional shallow-water flow around a cavity driven by a sinusoidally oscillating external flow was studied numerically. A container model of "T" shape was constructed in the numerical computation for comparison with the experimental observation. The numerical computation shows that the aspect ratio of the cavity is not much affecting the overall flow pattern, and for the aspect ratio 2, the deep region of the cavity has a stagnant flow motion. At larger Reynolds number, the flow field is characterized by many small vortices which are not present in the flow visualization. The flow pattern in the external region is in good agreement with the experimentally recorded particle trajectories. It turns out that two large coherent vortices situated in the exterior region of the cavity are responsible for clockwise and counterclockwise drift motions, in large scale, of particles.particles.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.4
• /
• pp.338-343
• /
• 2013

The Flowfield characteristics of a square prism having a detached splitter plate at the wake region were investigated by visualization of the flow field using PIV. The experimental parameters were the width ratios(H/B=0.5~1.5) of the splitter plate to the prism width and the gap ratios (G/B=0~2) between the prism and the splitter plate. As the results the Strouhal number measured at the wake region of the detached splitter plate was decreased with the width ratio and the gap ratio. The clockwise vortex at the upside of the splitter plate and counterclockwise vortex at the downside were represented, the size of these vortices were increased with the width of the splitter plate. The reverse flow was represented at the wake region of the square prism having a detached splitter plate, the size of this reverse flow was increased with the width of the splitter plate.