• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.5
• /
• pp.452-461
• /
• 1997

In this paper, we present a computer-aided design(CAD) technique for minimizing the phase shift in microstrip PIN diode attenuators due to the junction capacitance in the equivalent circuit model of PIN diode. Microstrip PIN diode attenuators use the characteristics which the reactance of microstrip line changes from inductive to capacitive as the frequency sweeps across the band. Microstrip PIN diode attenuator designed utilizes the quarter-wavelength transmission line terminating with the half-moon radial stub, which is designed for negligible phase shifting effect over the intersted bandwidth. The attenuator has similar phase shift at 0 dB and 10 dB of attenuation within average $1.27^{\circ}$ between 1.2GHz and 1.9GHz. The input and output return losses between 1.4 GHz and 1.9 GHz are less than 10 dB over the attenuation range of 0 dB and 10 dB.

• Resources Recycling
• /
• v.9 no.6
• /
• pp.31-35
• /
• 2000

The complex permeability, the complex permittivity and the reflection loss are investigated in the composite microwave absorbers which are mixed with the wasted Mn-Zn ferrite and the industrial cement. The cement has larger the complex permittivity than that of the rubber. The complex permittivity is decreasing with the increment of the mixing ratio of Mn-Zn ferrite to cement (F/C in weight) and the complex permeability is increasing with the increment of F/C. The maximum reflection loss is above -40 dB at all samples. The matching frequency is in the range of 1.3 GHz to 2.9 GHz and is decreasing with the increment of F/C from 1 to 3. The matching thickness is increasing with the increment of F/C. The wasted Mn-Zn ferrite and the cement is very useful material for the composite microwave absorber.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2066-2070
• /
• 2009

A voltage controlled attenuator using a PIN diode and two resistors of the $\pi$-type fixed attenuator is described in this paper. The proposed variable attenuator operating for a fixed attenuation range has a good input VSWR and a low intermodulation signal. For the low phase shift, a PIN diode is connected with open stub for the purpose of phase compensation. The stub for phase compensation is calculated by the Deloach method and the related circuit theory. This attenuator is easily fabricated on the microstrip and can be normally used in fine control circuits within small attenuation range. The fabricated attenuator for 2110~2170 MHz frequency band has about 4 dB of an attenuation range, $2^{\circ}$ of phase variance, and -20 dB of S11 according to the input voltage from 0 to 2.7 V.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.109-114
• /
• 2000

In this paper, we studied the relation between heat-treatment temperature of ferrite and electromagnetic wave absorbing properties of ferrite-rubber composite. The heat-treatment temperatures of ferrite are 1200 and 1300 $^{\circ}C$, 2 hr. As s result, it has been shown that the optimum heat-treatment temperature of ferrite for electromagnetic wave absorber are related to the chemical composition. And, we can control electromagnetic wave absorbing properties of ferrite-rubber composite by the control of heat-treatment temperature of ferrite.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.15 no.2
• /
• pp.364-370
• /
• 1995

The purpose of this paper was to develop a nondestructive evaluation method of sintered material by ultrasonic method. The density distribution of sintered material becomes inhomogeneous partially because of the friction between the powder and the die during compaction. The inhomogeneity was investigated by measurement of the energy attenuation coefficient and the shift of the center frequency in the frequency spectrum of the ultrasonic reflection echo. The experimental results showed that the center frequency of reflection wave depended linearly on the density of sintered materials. However, the attenuation coefficient decreased inversely as the density increased. This study shows that the shift of the center frequency in the frequency spectrum of reflection wave can be used to a nondestructive evaluation of sintered materials.

• Journal of the Korean Magnetics Society
• /
• v.1 no.2
• /
• pp.49-54
• /
• 1991

In this study the correlation between material constants and microwave absorbing characteristics of ferroxplana composite microwave absorber used in X-band was investigated. The real part of permeability(${\mu}_{r}'$) was decreased and the imaginary part of permeability(${\mu}_{r}"$) of ferroxplana composite was increased with increaing ferroxplana loading ratio(F/R). The frequency showing maximum attenuation was shifted to lower frequency with increasing absorber thickness. The absorber 2.6 mm thick showed good band width property and 3.2 mm thick showed good attenuation property. From the apphcation of ferroxplana composite's material constants to the region of material constants which satisfy broad band width, it is found that the absorbing characteristics were estimated quantitatively. Estabhshment of material constants' region which satisfies broad band width can make practical application to design of high performance ferrite microwave absorber.

• Korean Journal of Optics and Photonics
• /
• v.29 no.1
• /
• pp.28-31
• /
• 2018

In this paper, we have proposed and demonstrated a variable optical attenuator (VOA) incorporating a dual-fiber collimator and a bimetallic actuator. The optical attenuation between input and output single-mode fibers was tuned by tilting the angle of a reflection mirror fixed on the bimetal. The bimetal was heated or cooled by a thermoelectric cooler (TEC) and then moved the reflection mirror, due to bending and unreeling. The desired optical attenuation can be obtained through adjusting the electrical input into the TEC. The fabricated device showed 0.5 dB of insertion loss, 0.2 dB of maximum polarization-dependent loss, and 40 dB of dynamic range. The response time was measured to be about 5 s.

• Annual Conference of KIPS
• /
• 2014.04a
• /
• pp.840-843
• /
• 2014

사실적 피부 렌더링은 피부 표면에서 일어나는 확산반사(Diffusion) 및 경면반사(Specular) 뿐 만 아니라 피부층 내에서 산란되어 나오는 산란광과 얇은 피부층을 통과하는 투과광 등을 고려하여 렌더링 되어야 한다. 이를 물리적인 개념들을 사용하여 실시간으로 계산하여 표현하는 것은 많은 계산량과 시간을 필요로 하므로 확산 반사 및 경면 반사 등을 미리 계산하여 텍스쳐로 저장하고 재사용하는 사전정의 BRDF 방법으로 근사화하여 표현할 수 있다. 하지만 사전정의 BRDF를 통해 생성된 피부 투과광색상 텍스쳐 맵은 그 색상이 고정되어있어 조명의 색상이 바뀌어도 피부를 투과하는 빛의 색상이 변하지 않아 부자연스러움을 보인다. 본 논문에서는 이러한 문제를 해결하기 위해 물체와 조명간의 거리를 이용하여 빛의 감쇠비율을 구하고 조명의 색상 값과 감쇠비율을 이용하여 피부 투과광 색상 텍스쳐 맵의 RGB채널 수정을 통해 피부 렌더링에서의 자연스러운 투과광 표현이 가능함을 보였다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.1
• /
• pp.111-120
• /
• 2017

In this paper, we propose novel feature extraction algorithm for classification of seabed sediment. In previous researches, acoustic reflection coefficient has been used to classify seabed sediments, which is constant in terms of frequency. However, attenuation of seabed sediment is a function of frequency and is highly influenced by sediment types in general. Hence, we developed a feature vector by using attenuation variation with respect to frequency. The attenuation variation is obtained by using reflected signal from the second sediment layer, which is generated by broadband chirp. The proposed feature vector has advantage in number of dimensions to classify the seabed sediment over the classical scalar feature (reflection coefficient). To compare the proposed feature with the classical scalar feature, dimension of proposed feature vector is reduced by using linear discriminant analysis (LDA). Synthesised acoustic amplitudes reflected by seabed sediments are generated by using Biot model and the performance of proposed feature is evaluated by using Fisher scoring and classification accuracy computed by maximum likelihood decision (MLD). As a result, the proposed feature shows higher discrimination performance and more robustness against measurement errors than that of classical feature.

• The Journal of the Acoustical Society of Korea
• /
• v.25 no.5
• /
• pp.246-256
• /
• 2006

The plane wave reflection coefficient is an acoustic property containing all the information concerning the ocean bottom and can be used as an input parameter to various acoustic propagation models. In this paper, we measure the plane wave reflection coefficient, the sound speed, thd the attenuation for saturated granular medium in the water tank. Three kinds of glass beads and natural sand are used as the granular medium. The reflection experiment is performed with the sinusoidal tone bursts of 100 kHz at incident angles from 28 to 53 degrees, and the sound speed and attenuation experiment are performed also with the same signal. From the measured reflection signal, the reflection coefficient is calculated with the self calibration method and the experimental uncertainties are discussed. The sound speed and the attenuation measurements are used for the estimation of the porosity and permeability, the main Biot parameters. The estimated values are compared to the directly measured values and used as input values to the Biot theory in order to calculate the theoretical reflection coefficient. Finally, the reflection coefficient predicted by Biot theory is compared to the measured reflection coefficient and their characteristics are discussed.