• Journal of the Korean Geotechnical Society
• /
• v.16 no.5
• /
• pp.149-155
• /
• 2000

응답변위법에서 이용되는 동지반강성계수의 적절한 평가법에 대한 제안을 하였다. 현재까지의 지진피해조사 및 장기간의 지진관측사례는 지반이 공진할 때의 변형모드가 지중구조물의 피해에 가장 직접적으로 관련이 있는 것으로 알려져 있다. 따라서, 지중구조물의 축방향의 지반의 변형모드와 그 타월 진동수를 특정하여 동지반강성계수를 평가했다. 동지반강성계수는 지반의 공진상태를 상정하고 있기 때문에 결과로써 지진파의 축방행 파장의 영향을 받지 않고, 관상구주물의 반경과 표층두께의 비, 표층두께에 대한 구조물의 매설위치, 표층지반과 기반의 임피단스비 라고 하는 3개의 무차원 변수에 의해 표현된다.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.4
• /
• pp.5-12
• /
• 1994

고속절삭을 통해서 가공능률과 가공정밀도의 향상을 도모할 수 있기 때문에, 최근에는 공작기계용 고속주축계가 많은 주목을 받고 있다. 본 연구에서는 주축 선단부에 무거운 척과 공작물이 위치하는 선반용 고속주축계의 동특성을 해석하기 위해서 유한요소법을 도입하였다. 특히 세장비가 비교적 작은 주축은 Timoshenko 이론으로, 폭이 유한한 베어링은 반경방향 외에도 모멘트방향의 강성 및 감쇠특성을 가지고 있는 것으로 모델화하였다. 그리고 선반용 고속주축계의 고유진동수와 감쇠비에 대한 주축회전수, 베어링의 지지특성, 베어링의 간격, 주축재료의 내부감쇠율 등의 영향을 고찰하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.1
• /
• pp.170-176
• /
• 1987

This study is concerned with dynamic characteristics of a circular ring with a concentrated mass attached. The equations of motion are set up and are solved by using Laplace transformation. The ratio of a concentrated mass to the mass of circular ring is used as a parameter. Experiment was performed by employing impulse test and the results show good agreement with those of analysis. The results of this study can be utilized in vibrational analysis of axisymmetric shells with slight asymmetries.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.2
• /
• pp.181-188
• /
• 2012

The present study on nitrogen-diluted non-premixed counterflow flames with finite burner diameters experimentally investigates the important role of the outer edge flame in flame extinction. Flame stability diagrams mapping the flame extinction response of nitrogen-diluted non-premixed counterflow flames to varying global strain rates in terms of the burner diameter, burner gap, and velocity ratio are explored. There exists a critical nitrogen mole fraction beyond which the flame cannot be sustained, and also the curves of the critical nitrogen mole fraction versus the global strain rate have C-shapes in terms of burner diameter, burner gap, and velocity ratio. In flames with sufficiently high strain rates, the curves of the critical nitrogen mole fractions versus global strain rate collapse into one curve, and the flames can have the 1-D flame response of typical diffusion flames. Three flame extinction modes are identified: flame extinctions through the shrinkage of the outer edge flame with and without an oscillation of the outer edge flame prior to the extinction and flame extinction through a flame hole at the flame center. The measured flame surface temperature and a numerical evaluation of the fractional contribution of each term in the energy equation show that the radial conductive heat loss at the flame edge destabilizes the outer edge flame, and the conductive and convection heat addition to the outer edge from the trailing diffusion flame stabilizes the outer edge flame. The radial conductive heat loss at the flame edge is the dominant extinction mechanism acting through the shrinkage of the outer edge flame.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.11
• /
• pp.1038-1045
• /
• 2010

The theory for a new electromagnetically biased combined radial and axial magnetic bearing is developed. This combined magnetic bearing uses two axial coils to provide the bias flux to the radial and axial air gaps of the combined bearing. One dimensional magnetic circuit model for this combined magnetic bearing is developed and analyzed such that flux densities and magnetic forces can be obtained. Three dimensional finite element model for the bearing is also developed and analyzed. Numerical analysis shows that the calculated magnetic forces from 1D model are well matched with those from the finite element model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.8
• /
• pp.2516-2523
• /
• 1996

The equations of motion for rotating contilever beams with a concentrated mass loated in an arbitrary position are derived. For the modeling of the concentrated mass the Dirac delta function is used for the mass density function. Parametric studies are performed with five dimensionless variables ; natural frequencies, angular velocity, hub radius, concentrated mass, and the mass location. The concentrated mass, whereverit may locate, lowers the natural frequencies of a stationaly beam. However, when the beam rotates, the natural frequencies(if they increase or decrease) are dictated by the location of the concentrated mass.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.1
• /
• pp.13-23
• /
• 2015

The paper experimentally deals with the radial in-plane vibration characteristics of disk-shaped piezoelectric transducers. The radial in-plane motion, which is induced due to Poisson's ratio in the piezoelectric disk polarized in the thickness direction, was measured by using an in-plane laser vibrometer, and the natural frequencies were measured by using an impedance analyzer. The experimental results have been compared with theoretical predictions obtained by simplified theoretical and finite-element analyses. It appears that the fundamental mode of a piezoelectric disk transducer is a radial mode and its radial displacement distribution from the center to the perimeter is not monotonic but shows maximum slightly apart from the perimeter. The theoretically-calculated fundamental frequencies agree well with the finite-element results for small thickness-to-diameter ratio, and they are accurate within 7 % error for the ratio up to 0.4.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.4
• /
• pp.71-82
• /
• 1999

An axisymmetric shell element which includes the effects of the meridional and circumferential cable prestresses is developed. The fluid-structure interaction is expressed as added mass effect which is in proportion to the acceleration of the structure in interface surface. The added mass is obtained by using finite element method under the assumption that the fluid is invicid, incompressible and irrotational. It is coded for personal computer by the maximum use of axisymmetic properties and the dynamic analysis are performed under seismic exitations. A ring element makes the characteristics of the axisymmetric shell to be fully utilized. The elgenvalue solutons under the initial prestresses and the internal fluid are well agreed with the exact solutions and references by using under 20 elements. The eigenvalues are decreased along the increasing the height of internal fluid and these effects are dominant under the lower wave numbers. The results of the seismic analysis show that the radial deflection under the meridional prestress is a little larger than that under the circumferential prestress.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.4
• /
• pp.21-28
• /
• 1997

In this study, comparison between Harris-theoretical values and experimental data of load-deflection characteristics in bearing was made. The experiments are conducted under the conditions of the various radial loads and speed of shaft. In the case of non-defective ball bearing, the experimental data agreed well with the Harris-theoretical values for the small steady radial load but not for the large steady radial load. For the radial load bearing, the experimental results show that the stiffness of bearing at the single and multiple defective bearing are bigger in the radial defectiion than in the axial deflection. Load-deflection characteristics for the bearing defect part make it possible to detect the presence of a defect in bearing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.4
• /
• pp.429-435
• /
• 2012

An abrasion due to continuous friction between a work roll and strip causes the mass of the work roll to be unbalanced in the rolling process. We developed a mathematical model for the rolling mill considering the unbalanced mass and verified the model experimentally. The work roll was approximated as a rigid rotor with eccentricity, and the effect of the unbalanced mass on chatter vibration was investigated. The joint forces computed by quasistatic analysis were applied to the work roll in the rolling mill. Transient responses were obtained, and frequency analysis was performed by solving equations of motion using a direct integration method. Horizontal vibrations were more strongly affected by eccentricity than vertical vibrations. In the horizontal direction, a small eccentricity of 1% of the work roll radius considerably increased the amplitude of the chatter frequency.