• Journal of the Korean Applied Science and Technology
• /
• v.27 no.2
• /
• pp.137-143
• /
• 2010

Oxide semiconductors Thin-film transistors are an exemplified one owing to its excellent ambient stability and optical transparency. In particular zinc oxide (ZnO) has been reported because It has stability in air, a high electron mobility, transparency and low light sensitivity, compared to any other materials. For this reasons, ZnO TFTs have been studied actively. Furthermore, we expected that would be satisfy the demands of flexible display in new generation. In order to do that, ZnO TFTs must be fabricated that flexible substrate can sustain operating temperature. So, In this paper we have studied low-temperature process of zinc oxide(ZnO) thin-film transistors (TFTs) based on silicon nitride ($SiN_x$)/cross-linked poly-vinylphenol (C-PVP) as gate dielectric. TFTs based on oxide fabricated by Low-temperature process were similar to electrical characteristics in comparison to conventional TFTs. These results were in comparison to device with $SiN_x$/low-temperature C-PVP or $SiN_x$/conventional C-PVP. The ZnO TFTs fabricated by low-temperature process exhibited a field-effect mobility of $0.205\;cm^2/Vs$, a thresholdvoltage of 13.56 V and an on/off ratio of $5.73{\times}10^6$. As a result, We applied experimental for flexible PET substrate and showed that can be used to ZnO TFTs for flexible application.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.3 s.106
• /
• pp.239-248
• /
• 2006

In this paper, the cryogenically cooled low noise amplifier module for radio telescope receiver front-end using pHE-MT MMIC is designed and fabricated. In the selection of MMIC, the MMIC fabricated with the pHEMTS providing successful cryogenic operation are chosen. They are mounted in the housing using the thin film substrate. In the design of the housing, the absorber and the elimination of the gap between the carrier and the housing as well removed the unnecessary oscillations by its structure. The mismatch is improved by ribbon-tuning to provide the best performance at room temperature. The fabricated module shows the gain of $35dB{\pm}1dB$ and the noise figure of $2.37{\sim}2.57dB$ at room temperature over $21.5{\sim}23.5GHz$. In the cryogenic temperature of $15^{\circ}K$ cooled by He gas, the measured gain was above 35 dB and flatness ${\pm}2dB$ and the noise temperatures of $28{\sim}37^{\circ}K$.

• Journal of the Korean Magnetics Society
• /
• v.24 no.4
• /
• pp.101-106
• /
• 2014

The glass/Ta(5.8 nm)/NiFe(5 nm)/Cu(2.3 nm)/NiFe(3 nm)/IrMn(12 nm)/Ta(5.8 nm) GMR-SV (giantmagneto-resistance-spin valve) multilayer structure films with a magnetoresistance ratio (MR) of 5.0 % and a magnetic sensitivity (MS) of 1.5%/Oe was deposited by dc magnetron sputtering method. Also, GMR-SV device having a width of $7{\mu}m{\sim}8{\mu}m$ similar to the diameter of RBC (red blood cell) was fabricated by the light lithography process. When RBCs coupled with several magnetic beads with a diameter of $1{\mu}m$ dropped upon the GMR-SV device having MR = 1.06% and MS = 0.3 %/Oe, there is observed the variation of about included of a resistance value of ${\Delta}R=0.4{\Omega}$ and ${\Delta}MR=0.15%$ around a external magnetic field of -0.6 Oe. From these results, the GMR-SV device having the width magnitude of a few micron size can be applied as the biosensor for the analysis of a new magnetic property of hemoglobin inside of RBC combined to magnetic beads.

• Korean Journal of Optics and Photonics
• /
• v.23 no.3
• /
• pp.124-127
• /
• 2012

We designed and fabricated dichroic filters for high-power fiber lasers to protect the pumping laser diode from counterpropagating laser beams. The transmittance at laser diode wavelengths of 905 nm~925 nm was designed to be less than 0.1% and the transmittance at the fiber laser or Brillouin scattering wavelengths of 1020 nm ~ 1100 nm was designed to be more than 99.9%. Since oxide materials have good adhesion to the $SiO_2$ substrate, $SiO_2/Ta_2O_5$ were used as coating materials. The filter was fabricated according to our optimized design and its characteristics were compared with the theoretical design. As a result, the transmittance at laser diode wavelengths of 905 nm~925 nm was measured to be less than 0.1%, and the transmittance at the fiber laser or Brillouin scattering wavelengths of 1020 nm~1100 nm was measured to be more than 95.5%, which coincided well with the theoretical design considering processing errors. The filter was found to operate well over 1W of input laser power.

• Korean Journal of Materials Research
• /
• v.10 no.12
• /
• pp.812-818
• /
• 2000

We studied the effects of Ge preamorphization (PAM) on 0.25$\mu\textrm{m}$ Ti-salicide junctions using comparative study with As PAM. For each PAM schemes, ion implantations are performed at a dose of 2E14 ion/$\textrm{cm}^2$ and at 20keV energy using $^{75}$ /As+and GeF4 ion sources. Ge PAM showed better sheet resistance and within- wafer uniformity than those of As PAM at 0.257m line width of n +/p-well junctions. This attributes to enhanced C54-silicidation reaction and strong (040) preferred orientation of the C54-silicide due to minimized As presence at n+ junctions. At p+ junctions, comparable performance was obtained in Rs reduction at fine lines from both As and Ge PAM schemes. Junction leakage current (JLC) revels are below ~1E-14 A/$\mu\textrm{m}^{2}$ at area patterns for all process conditions, whereas no degradation in JLC is shown under Ge PAM condition even at edge- intensive patterns. Smooth $TiSi_2$ interface is observed by cross- section TEM (X- TEM), which supports minimized silicide agglomeration due to Ge PAM and low level of JLC. Both junction break- down voltage (JBV) and contact resistances are satisfactory at all process conditions.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.157-157
• /
• 2016

최근 많은 산업의 발전으로 인해 환경오염을 유발시키는 폐수가 다량으로 배출되고 있으며, 이러한 폐수 속에는 유기용매, 고분자 물질 및 각종 염 등의 난분해성 물질들이 다량으로 함유되어 있다. 이런 물질들을 분해시키기 위해 물리적, 생물학적 수처리 방법이 많이 이용되고 있지만 이 방법들은 각각 운전비용과 처리비용이 고가인 단점이 있다. 따라서 비용과 효율 측면에서 효과적인 폐수처리를 위해서 전기화학적 폐수처리 방법이 많이 사용되고 있다. 물리적, 생물학적 처리 방법에 비해 비용이 적게 들고, 처리 후 잔류물이 남지 않으며. 독성을 띄는 산화제의 첨가 없이도 높은 폐수처리 능력을 보이기 때문에 친환경적이므로, 전기화학적 폐수산화 처리에 사용되는 불용성 전극에 대한 연구가 많이 진행되어져 오고 있다. 그 중 BDD(Boron-doped diamond) 전극은 표면에서 강력한 산화제인 수산화 라디칼의 높은 발생량으로 인해 뛰어난 폐수처리 능력을 보이므로 불용성 전극 분야에서 활발한 연구가 진행 중이다. 그러나 기존에 BDD 전극의 기판 모재로 이용되던 Si, W, Pb등은 모두 기계적 강도. 폐수처리 능력 및 독성 문제로 인해 한계가 있었고, 특히 Nb기판 위에 형성시킨 BDD 전극은 뛰어난 폐수처리 능력에도 불구하고 비싼 모재 원가로 인해 상용화가 힘든 실정이다. 이런 문제점을 해결하기 위해 높은 기계적 강도와 전기화학적 안정성을 가진 Ti 기판을 사용한 BDD 전극에 대한 연구가 보고되고 있다. 그러나 BDD와 Ti 간의 lattice mismatch, BDD층 형성을 위한 고온 공정 시 탄소의 확산으로 인한 기판 표면에서의 TiC층 형성으로 인해 접착력이 감소하여 박리가 생기는 문제점이 있다. BDD와 Ti의 접착력을 향상시키기 위해 융점이 높고, 전기전도성이 우수한 TiN을 diffusion barrier layer로 삽입하면 탄소 확산에 의한 TiC층의 생성을 억제하여, 내부응력에 기인한 접착력 감소를 방지할 수 있다. 또 하나의 방법으로 Ti 기판의 전처리를 통해 BDD층의 접착력을 향상 시킬 수 있다. Sanding과 etching을 통해 기판 표면의 물리, 화학적인 표면조도를 부여하고, seeding을 통해 diamond 결정 성장에 도움을 주는 seed 입자를 분포시킴으로써, 중간층과 BDD층의 접착력을 향상시키고, BDD 결정핵 성장을 촉진시켜 고품질의 BDD박막 증착이 가능하다. 본 연구에서는 기존 Si, Nb 등의 기판 모재를 Ti로 대체함으로써 제조원가를 절감시키고, TiN 중간층을 삽입하여 접착력을 향상시킴으로써 기존의 BDD 전극과 동등한 수준의 물성 및 수처리 특성을 가진 BDD전극 제작을 목표로 하였다. $25{\times}25mm$의 Ti 기판위에 TiN 중간층을 DC magnetron sputtering을 이용하여 증착 후, BDD 전극 층을 HFCVD로 증착하였다. 전처리를 진행한 기판과 중간층 및 BDD층의 미세구조를 XRD로 분석하였고, 표면 형상을 SEM으로 확인하였다. BDD전극의 접착력 분석을 통해 TiN 중간층의 최적 조성을 도출하고, 최종적으로 BDD/TiN/Ti 전극의 CV특성과 가폐수의 COD분해능력 및 축산폐수, 선박평형수 등의 실제 폐수 처리 능력을 BDD/Si, BDD/Nb 전극과 비교 검토할 것이다.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.1
• /
• pp.55-60
• /
• 2012

In order to develop electroless-plated Nickel Phosphate (Ni-P) as a contact material for high efficient low-cost silicon solar cells, we evaluated the effect of ambient thermal annealing on the degradation behavior of interfacial adhesion energy between electroless-plated Ni-P and silicon solar cell wafers by applying 4-point bending test method. Measured interfacial adhesion energies decreased from 14.83 to 10.83 J/$m^2$ after annealing at 300 and $600^{\circ}C$, respectively. The X-ray photoelectron spectroscopy analysis suggested that the bonding interface was degraded by environmental residual oxygen, in which the oxidation inhibit the stable formation of Ni silicide phase between electroless-plated Ni-P and silicon interface.

• Journal of the Korean Magnetics Society
• /
• v.22 no.5
• /
• pp.173-177
• /
• 2012

The multilayer structure of glass/Ta(5.8 nm)/NiFe(5 nm)/Cu(t nm)/NiFe(3 nm)/FeMn(12 nm)/Ta(5.8 nm) as typical GMR-SV (giant magnetoresistance-spin valve) films is prepared by ion beam sputtering deposition (IBD). The coercivity and magnetoresiatance ratio are increased and decreased for the decrease of Cu thickness when the thickness of nonmagnetic Cu layer from is varied 2.2 nm to 3.0 nm. It means that the decrease of non-magntic layer is effected to the interlayer exchange coupling of pinned layer and the spin configuration array of free layer. For experiment of detecting and dropping of magnetic beads we used the GMR-SV sensor with glass/Ta/NiFe/Cu/NiFe/FeMn/Ta structure. From the comparison of before and after for the dropping status of magnetic bead, the variations of MR ratio, $H_{ex}$, and $H_c$ are showed 0.9 %, 3 Oe, and 2 Oe, respectively. The fabrication of GMR-SV sensor was included in the process of film deposition, photo-lithography, ion milling, and MR measurement. Further, GMR-SV device can be easily integrated so that detecting biosensor on a single chip becomes possible.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.2
• /
• pp.67-72
• /
• 2012

In recent days, the wire width of IC is narrowed and the degree of integration of IC is increased to obtain the higher capacity of the devices in electronic industry. And then the surface quality of FCCL(Flexible Copper Clad Laminate) became increasingly important. Surface defects on FCCL are bump, scratch, dent and so on. In particular, bumps cause low reliability of the products. Even though there are bumps on the surface, if leveling characteristic of plating solution is good, it does not develop significant bump. In this study, the leveling characteristics of additives are investigated. The objective of study is to improve the leveling characteristic and reduce the surface step through additives and plating conditions. The additives in the electrodeposition bath are critical to obtain flat surface and free of defects. In order to form flat copper surface, accelerator, suppressor and leveler are added to the stock solution. The reason for the addition of leveler is planarization surface and inhibition of the formation of micro-bump. Levelers (SO(Safranin O), MV(Methylene Violet), AB(Alcian Blue), JGB(Janus Green B), DB(Diazine Black) and PVP(Polyvinyl Pyrrolidone) are used in copper plating solution to enhance the morphology of electroplated copper. In this study, the nucleation and growth behavior of copper with variation of additives are studied. The leveling characteristics are analyzed on artificially fabricated Ni bumps.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1056-1063
• /
• 2006

Thermal evaporated 10 nm-Ni/l nm-Ir/(or polycrystalline)p-Si(100) and 10 nm-$Ni_{50}Co_{50}$/(or polycrystalline)p-Si(100) films were thermally annealed using rapid thermal annealing fur 40 sec at $300{\sim}1200^{\circ}C$. The annealed bilayer structure developed into Ni(Ir or Co)Si and resulting changes in sheet resistance, microstructure, phase and composition were investigated using a four-point probe, a scanning electron microscopy, a field ion beam, an X-ray diffractometer and an Auger electron spectroscope. The final thickness of Ir- and Co-inserted nickel silicides on single crystal silicon was approximately 20$\sim$40 nm and maintained its sheet resistance below 20 $\Omega$/sq. after the silicidation annealing at $1000^{\circ}C$. The ones on polysilicon had thickness of 20$\sim$55 nm and remained low resistance up to $850^{\circ}C$. A possible reason fur the improved thermal stability of the silicides formed on single crystal silicon substrate is the role of Ir and Co in preventing $NiSi_2$ transformation. Ir and Co also improved thermal stability of silicides formed on polysilicon substrate, but this enhancement was lessened due to the formation of high resistant phases and also a result of silicon mixing during high temperature diffusion. Ir-inserted nickel silicides showed surface roughness below 3 nm, which is appropriate for nano process. In conclusion, the proposed Ir- and Co- inserted nickel silicides may be superior over the conventional nickel monosilicides due to improved thermal stability.