• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.510-516
• /
• 2007

The proposed method offers an improved control method for high power density AC/DC adapter by using more energy efficient electrical equipments. Power factor correction (PFC) topology is based on boost topology with boundary conduction mode (BCM). DC/DC topology is based on half-bridge topology with fixed 50% duty and newly introduced off-time control method, which helps to reduce size of the semiconductor and the magnetic devices. Test results with 85W AC/DC adapter (18.5V/4.6A) design show that the measured efficiency is 90% with power density of $36W/in^3$. It also shows low no load power consumption of about 0.5W.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.4
• /
• pp.259-265
• /
• 2010

The proposed method offers an improved control method for high power density AC/DC adapter by using more energy efficient electrical equipments. Power factor corrector (PFC) topology is based on boost topology with boundary conduction mode (BCM) and DC/DC topology is based on LLC resonant converter, which helps to reduce size of the semiconductor and the magnetic devices. Test results with 85W AC/DC adapter (18.5V/4.6A) design shows that the measured efficiency is 90% at $90V_{rms}$ input voltage with power density of $36W/in^3$. It also shows low no load power consumption of about 0.5W.

• Journal of Bio-Environment Control
• /
• v.32 no.3
• /
• pp.197-204
• /
• 2023

Heat stress causes a decrease in immunity and disease occurrence in livestock, increasing mortality and impairing productivity. In particular, chickens are very vulnerable to high temperatures compared to other livestock species because their entire body is covered with feathers and sweat glands are not developed. Currently, air conditioning systems are essential in broiler houses to prevent high-air temperature damage to broilers, but conventional cooling facilities are greatly affected by the external environment, so there are limits to their use. In this study, to propose a cooling method, thermal insulation paint and a heat pump were apply in the broiler houses to evaluate the temperature reduction effect. The heat pump experiment was to analyze the cooling effect according to the change in ventilation rate and propose an appropriate. As a result of the experiment, the heat-insulating paint reduced the temperature of the broiler houses by maximum 1-2℃, and in the broiler houses where the heat pump was operated, the temperature decrease was the largest when the ventilation rate was the lowest. When the air temperature in the house is similar to or lower than the outside air temperature, it is considered to be most effective to use a heat pump while maintaining only the minimum ventilation rate.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.6-6
• /
• 2017

농용트랙터의 전방차축 현가장치는 노면으로부터 발생하는 진동의 영향을 줄일 수 있기 때문에 트랙터의 대형화, 고속화의 추세에 맞춰서 승차감과 조향감을 향상시키는 데 중요한 역할을 한다. 전방차축의 현가장치는 트랙터의 차체 무게에 의한 부하가 크고, 또한 유압 펌프를 비롯한 유압시스템이 존재하기 때문에 유압식 회로로 구성하는 것이 바람직하다. 하지만, 현가장치의 유압회로를 개발하는데 있어서 실제 시스템을 구성하여 실제 실험을 통한 개발에는 비용과 시간이 많이 필요하다. 본 연구에서는 유압식 전방차축 현가장치에 필요한 유압회로부 개발을 위하여 시뮬레이션 기법과 요인시험 장치를 이용 적정 유압회로를 설계하고자 하였다. 이를 위하여 어큐뮬레이터, 가변 오리피스, 릴리프밸브, 체크밸브 등으로 구성된 유압 현가요인 시험 장치를 설계 제작하였으며, 현가 부품인 실린더 행정, 속도, 전달되는 힘을 측정하고, 유압 해석 프로그램인 SimulationX를 이용 구성된 유압회로 부품에 측정값을 입력하여 실제 조건과 유사한 동특성을 나타내는 전방차축 현가요인 시뮬레이션 모델을 개발하였다. 개발된 시뮬레이션 모델을 이용하여 실제 시험조건과 같은 가진 조건을 부여하여 개발 현가장치의 특성 값 변동에 따른 현가 성능을 구명하였다. 이를 위해 시뮬레이션 상에서 120 마력 트랙터 무게의 50% 수준에 해당하는 2,000 kg의 부하가 존재하는 상태에서 현가장치의 유/무에 따른, 감쇠 계수의 변화에 따른 스프링상 질량의 RMS 가속도를 비교하였다. 입력 가진으로는 1 Hz, 4 Hz, 8 Hz의 진동수에 각각 10 mm, 6.4 mm, 3.2 mm의 진폭을 인가하였다. 시뮬레이션 결과, 1 Hz에서는 현가장치가 있는 경우 최대 55.9% 개선되었고, 4 Hz에서는 최대 3.9 % 개선되었고, 8 Hz에서는 최대 61.4%까지 개선되었다. 이는 4 Hz의 경우에는 2,000 kg의 부하에 해당하는 고유 진동수 대역에 해당하기 때문에 그 감쇠 효과가 없는 것으로 나타났다. 하지만, 다른 주파수 대역에서는 현가장치가 효과적으로 작동하는 것을 나타내었다. 설계한 전방차축 현가 유압회로부를 시뮬레이션을 통하여 분석한 결과, RMS 가속도의 개선이 명확하게 이루어지는 것을 확인하였으며 입력 주파수 변화에 따라 감쇠특성도 나타나는 것을 확인하였다. 추후 연구에는 설계한 유압회로부와 관련 부품을 설계 제작하여 실제 트랙터에 장착 그 성능을 검증할 예정이며, 노면조건에 따라 감쇠성능을 유지하기 위한 반능동형 또는 적응형 현가장치 제어 기술을 적용하여 개선된 현가성능을 확보하기 위한 연구를 수행할 예정이다.

• The KIPS Transactions:PartA
• /
• v.10A no.3
• /
• pp.189-198
• /
• 2003

In this paper, we propose a method of analysis to show the heavy-tailed statistical distribution of file sizes in web servers, using TTT plot technique. TTT plot technique, a well-known method in the area of reliability engineering, determines that a distribution of samples fellows a heavy tailed one when their TTT statistical plots are lied on a straight line. We performed an intensive simulation using data gathered from real web servers. The simulation indicates that the proposed method is superior to Hill estimation technique or LLCD plot method in efficiency of data analysis. Moreover, the proposed method eliminates the possible decision error, which Pareto distribution or traditional method might cause.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.65-74
• /
• 1993

A miniature size electrostatic induction motor has been fabricated and studied with emphasis on the role of the surface resistivity, the relative dielectric constant and the charge relaxation time constant of the rotor surface materials and the rotor liner materials, which, however, control the surface charge induction and relaxation on the rotor material surface and the field intensity between the rotor and the stator of the motor. It is found that the surface resistivity and/or the relative dielectric constant, and the charge relaxation time constant of the rotor surface material enfluenced significantly to motor speed controlled by the surface charge induction and relaxation on the rotor surface depending on the applied voltage and/or frequency changing. The resistivity of the rotor liner material is also found to be effected to the motor speed greatly by control of the field intensity between the rotor and the stator and of the surface charge distribution of the induced charge on the rotor. As a result, a maximum no load rotor speed of the motor tested was about 5500 rpm at the applied voltage of 4.5 kV and the frequency of 220 Hz for the case of the rotor surface material of $BaTiO_{3}$ 80% in the resin binder layered on the copper-foil rotor liner material.

• Clinics in Shoulder and Elbow
• /
• v.12 no.2
• /
• pp.207-214
• /
• 2009

Purpose: In arthroscopic rotator cuff repairs there are generally weak link in tendon suture interface, arthroscopic rotator cuff repairs can have higher retear rates than open repairs. The purpose of this study was to compare the strength of UU (Ulsan University) suture than open modified MA (Mason-Allen) suture when suture anchored into bone. Materials and Methods: The human supraspinatus tendons were harvested from the shoulder of the cadaver and split in 2 times, producing four tendons per one shoulder, for a total of 24 specimens. Two suture configurations (UU, MA) were randomized and checked on each set of tendons. Specimens were cyclically loaded under force control between 5 and 30 N at 0.25 Hz for fifty cycles. Each specimen was loaded to failure under displacement control at 1 mm/sec. Cyclic elongation, peak to peak displacement, stiffness, ultimate tensile load, mode of failure were checked. Results: No significant difference was found between two suture configuration with respect to peak to peak displacement, cyclic elongation, and stiffness. With regard to ultimate failure load, there were no significant difference statistically between the UU suture and modified MA suture (109.4 N, 110.6 N). The most common mode of failure between both sutures was suture pull-out through the tendon. Conclusion: The UU suture and modified MA suture produced similar biomechanical properties.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.152-152
• /
• 2017

본 연구에서는 비례제어밸브를 이용한 자율주행 트랙터 조향 시스템 제어를 위하여 저가의 임베디드 시스템을 사용한 제어기를 개발하였다. 차륜의 조향각 측정을 위하여 전륜 킹핀에 포텐시오미터를 설치하였으며, 비례제어밸브는 -10 ~ +10V의 전압으로 밸브 스풀의 위치제어를 수행하도록 하였다. 조향각 측정과 비례제어밸브의 위치제어를 위하여 각각에 AT90CAN128 AVR보드를 사용하였으며, CAN통신으로 조향각 데이터가 비례제어밸브 제어용 데이터로 전송될 수 있도록 하였다. 비례제어밸브 제어 보드에는 DAC기능을 추가하였으며 0 ~ 5V의 출력을 -10 ~ +10V의 전압으로 변환해 주는 인터페이스회로를 추가하였다. 일반적으로 GPS 등의 데이터 수신율이 20 Hz인 점을 감안하여 비례제어 밸브는 50 ms의 주기로 P-제어를 수행할 수 있도록 하였다. 향후 트랙터의 방향각을 설정하는 또 하나의 시스템으로부터 목표 조향각을 부여받는 것을 가상하여 별도의 MCU를 통해 목표 조향각을 송신한 후, 조향 유압실린더에 의한 전륜의 조향각 시간 응답 특성을 조사하였다. 실험은 트랙터의 전륜을 지면으로부터 들어올린 무 부하 상태에서 진행하였으며, 목표 조향각은 $7.5^{\circ}$, $15.0^{\circ}$, $22.5^{\circ}$ 등 3단계로 변경하며 시간응답 특성을 측정하였다. 최대 오버슈트 11%, 최소 오버슈트 8.6%, 정상상태 오차 약 $0.825^{\circ}$, 시정수(Time Constant)는 3단계의 목표 조향각 설정에서 각각 0.706초, 0.488초, 0.38초로 나타났다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.4
• /
• pp.349-357
• /
• 2017

If an actuation system of the tactical missile is required very fast response time on conditions of short operating time and big loads on the actuator, we would prefer to adopt a small hydraulic system. In this paper, a mathematical model is proposed to analyze and simulate the small hydraulic actuation system. The mathematical model consists of a high pressure vessel model, a pressure regulator model, a hydraulic reservoir model and a actuator model. The suggested model is validated by comparison of simulation results with experimental data. The simulation results show that the mathematical model could be useful for designing a hydraulic actuation system.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.260-268
• /
• 2020

This paper presents the high frequency resonant inverter of class D SEPP(Single-Ended Push Pull) type using LS-ZVS-LSTC, which can reduce the switching losses during the turn-on and turn-off switching time. The analysis of high frequency resonant inverter using LS-ZVS-LSTC(Low-loss Turn-off Snubber Capacitor) proposed in this paper is described in general by adopting the normalized parameters. The operating characteristics of the proposed high frequency resonant inverter were also evaluated by using the control parameters such as the normalized control frequency(μ), the normalized load time constant(τ), the coupling factor(κ) and so on. Based on the characteristic values through the characteristics of evaluation, an example of the design method of the 1.8[kW] class D SEPP type high frequency inverter is suggested, and the validity of the theoretical analysis is verified using the experimental data.