• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.3
• /
• pp.83-89
• /
• 2000

In hydraulic control system turbine and gear motor type flowmeters are widely used to measure the flow rate under steady flow conditions. With the recent growth of interest in the measurement of instantaneous values of unsteady flow rate the test of the transient response of these flowmeters are in some significance. however an unsteady flow rate mea-surment and its calibration method with a fast response and a high accuracy have not beendeveloped. In this research particularly the dynamic characteristics of turbine and gear motor type flowmeters are investigated experimentally and simple mathematical models are proposed. The measured flow rate waveforms are compared with those by remote instan-taneous flow rate measurement method(RIFM) which has been developed by author and used for calibration As the result of frequency response test gain and phase between the measured flow rate waveforms by turbine type flowmeter and those estimated by RIFM are in good agreement up to 70Hz For the gear motor type flowmeter th simulated results by a math-ematical model proposed here agree well with the experiment nearly up to 100Hz. Also it if sound that the pressure drop across the flowmeter is increased in proportion to the frequency of the flow rate variation in a high frequency region of more than 100Hz. It can be explained that the dealy of gear motor type flowmeter in high frequency regionis mainly attributed to a first order delay consisting of the inertia of gears and internal leakage of the gear motor.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.398-401
• /
• 2007

The performance characteristics of Polyethylene-Nitrous oxide (PE-N2O) hybrid rocket motor with the variation of the grain geometry was investigated. To compare the performance parameters under the different port number, single and four port grains were used in this study. In order to improve the performance by enhancing mixing between fuel and oxidizer, the fuel grain having the mixing chamber was additionally studied. From the motor firing tests, it is found that the motor having 4-port fuel grain with the mixing chamber showed the highest performance among all cases. Therefore we have confirmed that with only the geometrical change of the fuel grain, it was possible to give quite influential improvement on the motor performance

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.2
• /
• pp.149-157
• /
• 2001

A nonlinear speed control for a permanent magnet synchronous motor (PMSM) using a simple disturbance estimation technique is presented. By using a feedback linearization scheme, the nonlinear motor model can be linearized in a controllable canonical form, and the desired speed dynamics can be obtained based on the linearized model. This technique, however, gives an undesirable output performance under the mismatch of the system parameters and load conditions. To cancel disturbance by parameter variation, the controller parameters will be estimated by using a disturbance observer theory where the disturbance torque and flux linkage are estimated. since only the two reduced order observers are used for the parameter estimations, the observer designs are considerably simple and the additional load for computation of the controller is negligibly small. The proposed control scheme is implemented on a PMSM using DSP TMS320C31 and the effectiveness is verified through the comparative simulations and experiments.

• Microbiology and Biotechnology Letters
• /
• v.15 no.6
• /
• pp.396-401
• /
• 1987

Protein productivities of a cloned gene ($\beta$-galactosidase) and the cultural performances of two recombinant Escherichia coli strains, which use different host-vector systems, were studied. E. coli JM109/pTBG10 strain which carries Tac promoter had higher protein productivity than E. coli MH3000 (pRKc1857)/pASI(lacZ) strain which carries pL promoter. Induction of protein syn-thesis was optimum at the initial-and mid-logarithmic growth phases for both strains. Oxygen demand was observed to be very high during the cloned gene expression, and could be alleviated to some extent through pH control. The ratio of specific growth rates of plasmid-harboring to plasmidfree cell, $\mu$+ /$\mu$-, of the high productivity strain was observed to be lower than that of the low productivity one. Plasmid stability was analyzed for 20-30 generations, and it was found that the traction of plasmid-harboring cells dropped to l0% level in about 25 generations for both strains when the cloned gene expression was induced.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.4
• /
• pp.456-462
• /
• 2015

The objective of this study was to develop an advanced pump technology using tornado and axial pumping principles without priming water. The developed rotor type slurry pump consisted of an electric motor, driving shaft and coupling, a rotor, an impeller, suction and discharge pipes. For the clean water test, the experimental results are presented for the discharge flowrate, electric power input and vacuum pressure with the rotor design parameters as a function of the motor rpm. The slurry discharge characteristics with the solid concentration of the cement slurry was performed. As the rotor diameter and height increase, the discharge flowrate and electric power input increase while the vacuum pressure in the suction pipe decreases. The rotor thickness had no significant effect on the discharge flowrate and electric power input. Slurries with more than 18 % solid concentration, which is the development factor, can be pumped.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1613-1622
• /
• 2010

In this paper, the ultraprecision positioning control of an ultrasonic linear motor in a high-vacuum environment is presented. The bolt-clamped Langivin type transducer (BLT) with the 3rd longitudinal; and 6th lateral vibration modes was developed, which was excited by using the Eigen resonance frequency for two vibration modes in order to generate stable and high power. In practical applications, however, even if a geometrical design has an Eigen frequency, discordance between both mode frequencies can be generated by the contact mechanism and because of manufacturing errors as well as environmental factors. Both mode frequencies were precisely matched by adjusting the impedence. By using this method, the BLT can be driven under any environmental conditions. The nominal characteristic trajectory following(NCTF) control method was adopted to control the positioning of the system in vacuum. The developed linear motor stage show high positioning accuracy with 5 nm.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.4
• /
• pp.142-151
• /
• 1999

Linear Pulse Motors (LPM) are used a field where SImOth linear motion is required, and it's position accuracy higher than that of a lead According to the advanUlge such as simplicity of rrechanical frarre, high reliability, precise open-loop operation, low inertia etc. LPM is awlied largely where it have made motor of this kind more and rmre attractive in many application areas such as factory automation and high speed positioning. This paper is researched to analyze for force characteristics of hybrid LPM with high accuracy and repeatability. Both the thrust and normal force are very sensitive to the airgap and tooth pitches of the forcer and platen. Here, the thrust shows a high content while the normal force is much higher than the thrust. For magnetic circuits of hybrid LPM is the complicated structure, the finite element rrethod (FEM) is employed with suitable rrethod for calculating the force. Therefore, both the virtual work principle and maxwell stress tensor have been used.n used.

• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.55-60
• /
• 2020

As research and development of eco-friendly vehicles are expanding worldwide, additional devices of vehicles are reduced or deleted to increase the mileage, or research is being conducted to reduce weight. Among them, the multi-stage transmission that was applied to the internal combustion engine vehicle was deleted and replaced with a reducer, and the initial driving power is secured by increasing the torque through the control of the motor output value. However, since frequent motor speed change can result in a load increase, this study attempts to develop a compact and lightweight manual two-stage reducer with a general reducer structure. Therefore, a two-speed transmission with two gear ratio was designed by inserting a large gear and a small gear in a structure with a parallel shaft to connect the gears with a V-belt in the form of a parallel shaft reducer, and setting the gear ratio of the low and high gears respectively. In addition, power performance according to the rotational speed and load of the transmission was checked through a test, and the heat generation characteristics generated during driving were checked to verify the validity of the transmission.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.488-493
• /
• 2022

In manufacturing sites, bearing fault in eletrically driven motors cause the entire system to shut down. Stopping the operation of this environment causes huge losses in time and money. The reason of this bearing defects can be various factors such as wear due to continuous contact of rotating elements, excessive load addition, and operating environment. In this paper, a motor driving environment is created which is similar to the domestic manufacturing sites. In addition, based on the established environment, we propose a dataset for bearing fault detection by collecting changes in vibration characteristics that vary depending on normal and defective conditions. The sensor used to collect the vibration characteristics is Microphone G.R.A.S. 40PH-10. We used various machine learning models to build a prototype bearing fault detection system trained on the proposed dataset. As the result, based on the deep neural network model, it shows high accuracy performance of 92.3% in the time domain and 98.3% in the frequency domain.

• Plant Journal
• /
• v.18 no.3
• /
• pp.28-40
• /
• 2022

As the proportion of renewable energy generation is expected to increase, public power generation businesses need to actively consider implementing the expansion of biomass mixing, In this study, the biomass co-firing rate is being changed from 0wt.% to 5.0wt.% at 500MW coal-fired power plant, measuring the major operation characteristics of the pulverizer. First, the composition analysis and grinding characteristics of lignocelluosic biomass were examined, and the effect of volume increase on dirrerential bowl pressure difference, motor current, coal spillage, outlet temperature, and internal fire count was analyzed. As the co-firing rate increased, it was confirmed that the difference in the differential bowl pressure, motor current, and coal spillage treated increased, and the outlet temperature was minimal. The number of internal fires is difficult to find a clear correlation, but it has been confirmed that it is highly likely to occur in combination with other driving factors.