• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.6
• /
• pp.81-91
• /
• 2003

Recently, many high-rise reinforced concrete(RC) bearing-wall structures of multiple uses have been constructed, which have the irregularities of weak(or soft) story and torsion at the lower stories simultaneously. The study stated herein was performed to investigate seismic performance of such a high-rise RC structure through a series of shaking table tests of a 1: 12 model. Based on the observations of the test results, the conclusions are drawn as follows: 1) Accidental torsion due to the uncertainty on the properties of structure can be reasonably predicted by using the dynamic analysis than by using lateral force procedure. 2) The mode coupled by translation and torsion induced the overturning moments not only in the direction of excitations but also in the perpendicular direction: The axial forces in columns due to this transverse overturning moment cannot be adequately predicted using the existing mode analysis technique, and 3) the hysteretic curve and the strength diagram between base shear and torque(BST) clearly reveal the predominant mode of vibrations and the failure mode.

• 기계와재료
• /
• v.23 no.4
• /
• pp.74-83
• /
• 2011

풍력발전기 동적 시뮬레이션 프로그램 개발을 위해 미국풍력기술연구센터(NWTC)의 프로그램군에 대해 분석하고 이를 소개하였다. 본 편에서는 에어포일 데이터를 생성하는 AirfoilPrep, IEC 61400-1 기준의 극한 조건에 해당하는 허브 높이의 바람 데이터를 생성하는 IECWind, 통계적인 방법에 의해 전 영역에 대한 난류 바람 데이터를 생성하는 TurbSim, 복합재료 블레이드의 구조적 특성치를 계산하는 PreComp, 블레이드와 타워의 모드 형상을 구하는 BModes와 같은 전처리기를 중심으로 설명하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1A
• /
• pp.125-133
• /
• 2008

According to longer and longer span, dynamic instability of stay cable should be prevented. Dynamic instability occurs mainly symmetric 1st mode and antisymmetric 1st mode in stay cable. Especially symmetric 1st mode has a lot of influence on sag. Therefore fundamental frequency of stay cable is different from that of taut sting. Irvine, Triantafyllou, Ahn etc. analyzed dynamic behavior of taut cable with sag through analytical technical and their researches give important results for large bounds of Irvine parameter. But each research shows mutually different values out of characteristic (cross-over or mode-coupled) point and each solution of frequency equations of all researchers can be very difficultly found because of their very high non-linearity. Presented study focuses on fundamental frequency of stay cable. Generalized mechanical energy with symmetric 1st mode vibration shape satisfied boundary conditions is evolved by Rayleigh-Ritz method. It is possible to give linear analytic solution within characteristic point. Error by this approach shows only below 3% at characteristic point against existing researches. And taut cable don't exceed characteristic point. I.e. high accuracy, easy solving techniques, and a little bit limitations. Therefore presented study can be announced that it is good study ergonomically.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.2
• /
• pp.126-131
• /
• 2010

The purpose of this study is to assess the condition of composites used in aircraft under varying temperature environment with ultrasound guided wave technique. Investigation of crucial influential factor on the composite health monitoring related to aircraft operational environments such as the number of thermal cycles and temperature deviation between ground level and flight altitude has been of a great concern for aircraft safety issue. In this study, ultrasonic guided wave health monitoring scheme is proposed to evaluate composite specimens damaged with the thermal fatigue simulating aircraft operational condition. Guided wave dispersion curves are used to select right modes which show a promising sensitivity to each different thermal fatigue damage level. The present approach can be also implemented as one of on-lines health monitoring tools for aircraft.

• Composites Research
• /
• v.16 no.5
• /
• pp.45-53
• /
• 2003

The experimental and numerical investigations on the failure characteristics of the secondary bonded composite single-lap joints were performed. The initiations and growths of cracks were observed using CCD camera and acoustic emission sensor during the tension tests of the joint specimens. The structural behaviors of the specimens were predicted by the geometric nonlinear two-dimensional finite element analysis. The three types of observed initial cracks were included in each finite element models and the strain energy release rates of each specimen models were calculated by VCCT(Virtual Crack Closure Technique) technique. The tension tests showed that the initial cracks occurred in the 60∼90% of final failure loads and the major failure modes of the specimens were adhesive failure and the delamination between the 1st and 2nd ply of laminate. The specimens with the thicker bondline had earlier crack initiation loads but higher crack propagation resistance and eventually better loading capability. The delaminations were mostly observed in the thicker bondline specimens. The mode I values of calculated strain energy release rates were higher than the mode II values in the all specimen models considering the three types of initial cracks. The mode I and total strain energy release rates were calculated as higher values in the order of initial crack in the edge interface, comer interface and delamination between the plies of laminate.

• Composites Research
• /
• v.21 no.1
• /
• pp.22-29
• /
• 2008

This paper presents the evaluation of crashworthiness and rollover characteristics of low-floor bus vehicles made of aluminum honeycomb sandwich composites with glass-fabric epoxy laminate facesheets. Crashworthiness and rollover analysis of low-floor bus was carried out using explicit finite element analysis code LS-DYNA3D with the lapse of time. Material testing was conducted to determine the input parameters for the composite laminate facesheet model, and the effective equivalent damage model for the orthotropic honeycomb core material. The crash conditions of low-floor bus were frontal accident with speed of 60km/h. Rollover analysis were conducted according to the safety rules of European standard (ECE-R66). The results showed that the survival space for driver and passengers was secured against frontal crashworthiness and rollover of low-floor bus. Also, The modified Chang-Chang failure criterion is recommended to predict the failure mode of composite structures for crashworthiness and rollover analysis.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.4
• /
• pp.1-8
• /
• 2001

In this paper, a hybrid mass damper using AC-servomotor was designed and developed in order to reduce vibration levels of a 5-story test structure under base excitation. Control performances of the HMD under random and earthquakes excitations are compared with those of TMD through experimental test. It is confirmed that the HMD is more effective to reduce the vibration levels of the test structure especially for the earthquake excitation which excites more than 2 vibration modes of the structure simultaneously.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.9-17
• /
• 2005

The aeroelastic stability enhancement of composite hingeless rotor system through the structural damping increase has been investigated. In order to increase structural damping of the rotor system, constrained layer damping (CLD) treatment is applied to the composite flexures. Modal analysis of composite flexures with attached viscoelastic and constraining layers are performed using MSC/NASTRAN, and the effectiveness of CLD treatments are validated through modal test. The composite flexures with CLD are applied to a hingeless rotor system. The rotor system is tested in hovering condition and it is shown that in-plane damping is increased by means of CLD treatments.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.228-233
• /
• 2001

Satellite system experiences severe mechanical loads during the launch period. Therefore, positive margin of safety of the satellite system must be demonstrated for every possible mechanical loading condition during the launch period. This paper presents modal and stress analysis result due to quasi-static loads for the satellite antenna system. The failure tendency for the sandwich construction of the satellite antenna system has been studied with various lamination angles of unidirectional prepreg.

• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.255-260
• /
• 2000

We report that the crack-free organic-inorganic hybrid silica thin films were fabricated by sol-gel process using organometallic compounds as a precursor and that we have established very reproducible fabrication condition with systematic investigation of thickness and refractive index variations for various control parameters, such as, coating type, coating speed, chemical composition, prebake and postbake temperature. Additionally, we measured and compared the change of optical property with the UV exposure dose for three different kinds of photoinitiators. Furthermore, the fabrication of Ix4 MMI optical power splitter using the sol-gel thin film provides the possibility of various applications to the optical waveguide devices. vices.