• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.223-224
• /
• 2015

배전 계통 산업 현장에서는 스위칭 소자 및 제어장치, 전 자기기들이 한 대 맞물려 증가하고 있다. 또한, 스마트 그리드(Smart Grid) 및 마이크로 그리드(Micro Grid)의 개념이 도입되면서 분산 전원 이 널리 보급되고 있다. 이로 인해 현장에서는 많은 전기전자기기들이 설치되어 운영 중에 있고, 이것은 noise 및 고조파와 같은 왜란이 발생 되는 원인을 초래하고 있다. 왜란은 여러 전기 전자 장비들의 데이터 취득 왜곡 현상을 발생시키고, 이러한 데이터 손실로 인해 기기들의 오동작 및 사고를 발생시킨다. 대표적인 왜란으로는 common mode noise 같은 대지(大地) 등의 기준점과 각 신호선 사이에 나타나는 노이즈가 있으며, 선로 및 장비 특성에 따라 기수 및 우수 고조파가 있다. 이러한 왜란들은 전자기기들의 오동작 및 신호의 부 정확성으로 제품 신뢰성에 문제를 초래한다. 특히 데이터 계측 실패 및 Serial 통신을 함에 있어서 신호 손실을 발생시켜 데이터 변형을 초래한다. 이로 인해 배전선로에 위치한 전자기기들이 왜곡된 데이터로 동작을 하게 되고 이는 곧 선로의 사고를 발생시키게 된다. 따라서 왜란들을 사전에 방지하여 기기 오동작 및 부동작을 예방하기 위해서 산업계에서는 왜란에 대한 인식을 지속적으로 증가시키고 있다. 실제 현장에서도 이와 같은 왜란으로 인해 기기 오동작을 하는 경우가 많으며 이를 해결하기 위한 여러 신호처리 기법을 적용하고 있다. 이에 본 논문에서는 여러 종류의 샘플링 데이터 량을 생성할 수 있도록 샘플링 속도를 다변환(Multi-interchange)하고 각 샘플링 속도에 맞게 계측된 샘플링 데이터를 DFT 신호 처리하여 왜란으로부터 강건한 계통 주파수를 계측한다. 또한, 주파수 별 DFT 값을 Table화 하여 계통 주파수를 찾아낸다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.906-912
• /
• 2017

In this paper, we studied a design method for a broadband 3-element quasi-Yagi antenna (QYA) for indoor digital television (DTV) reception. The proposed QYA employs a novel balun between a microstrip (MS) line and a coplanar strip (CPS) line feeding the driver dipole. The proposed balun is constructed by connecting the end of MS line to CPS line through a shorting pin, and the CPS and ground reflector are connected through a circular ring-type conductor. An antenna, as an design example for the proposed antenna, is designed for the operation in the frequency band of 470-806 MHz for terrestrial DTV. The antenna fabricated on an FR4 substrate with a size of $270mm{\times}150mm$ showed a good performance such as a frequency band of 470-820 MHz for a voltage standing wave ratio < 2, a gain > 4.0 dBi, and a front-to-back ratio > 8.4 dB over the DTV frequency band.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.4
• /
• pp.1903-1907
• /
• 2013

Heart condition should be observed for long periods of time because it does not appear abnormal all the time. However, there are many difficulties checking our health for a long time due to its size, operation of equipment, and cost. To solve these problems, an electrocardiograms(ECG), specially interfacing three gel-less metal electrodes for low cost portable applications, is designed and implemented. Gel-less metal electrodes are used for ECG monitoring system instead of gel-type electrodes that can cause skin rashes and itching problem. The whole ECG system consists of two parts-analog and digital circuits. The analog measurement circuit that has a 18*25mm size is made up of op-amps maintaining a sufficiently high common-mode noise rejection and passive elements of SMD type. Analog heart signal is converted to digital stream suitable for display on a TFT-LCD by an 8-bit microcontroller. The size of the completed ECG system is 25*80*50mm and its weighing is about 150g, which is small enough to be easily used. Therefore, the implemented ECG system can be used as a portable one.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.2
• /
• pp.146-153
• /
• 2008

Integrated humidity sensor system with two stages operational amplifier has been designed and fabricated by $0.8{\mu}m$ analog mixed CMOS technology. The system (28 pin and $2mm{\times}4mm$) consisted of Wheatstone-bridge type humidity sensor, resistive type humidity sensor, temperature sensors and operational amplifier for signal amplification and process in one chip. The poly-nitride etch stop process has been tried to form the sensing area as well as trench in a standard CMOS process. This modified technique did not affect the CMOS devices in their essential characteristics and gave an allowance to fabricate the system on same chip by standard process. The operational amplifier showed the stable operation so that unity gain bandwidth was more than 5.46 MHz and slew rate was more than 10 V/uS, respectively. The drain current of n-channel humidity sensitive field effect transistor (HUSFET) increased from 0.54 mA to 0.68 mA as the relative humidity increased from 10 to 70 %RH.

• Journal of Astronomy and Space Sciences
• /
• v.22 no.4
• /
• pp.537-558
• /
• 2005

This paper addresses the results of HAUSAT-2 radiation environment and effect analyses, including TID and SEE analyses. Trapped proton and electron, solar proton, galactic cosmic ray models were considered for HAUSAT-2 TID radiation environment analysis. TID was analyzed through total dose-depth curve and the radiation tolerance of TID for HAUSAT-2 components was verified by using DMBP method and sectoring analysis. HAUSAT-2 LET spectrum for heavy ion and proton were also analyzed for SEE investigation. SEE(SEU, SEL) analyses were accomplished for MPC860T2B microprocessor and K6X8008T2B memory. It was estimated that several SEUs may occur without SEL during the HAUSAT-2 mission life(2 years). Software Hamming Code EDAC has been implemented to detect and correct the SEU. In this study, all radiation analyses were conducted by using SPENVIS software.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.413-413
• /
• 2011

최근 전기, 전자, 반도체 산업의 발전으로 전 고상 박막리튬전지는 초소형, 초경량의 마이크로 소자의 구현을 위한 고밀도 에너지원으로 각광받고 있다. 현재 양극박막은 대부분LCO(LiCoO2)계열이 이용되고 있으나, 코발트는 높은 가격과 인체 유해성 뿐만 아니라 상대적으로 낮은 용량(~140 mAh/g)등의 단점을 갖고 있어 향후 보다 고용량의 양극박막이 요구된다. 3원계 양극활물질 LiMO2(M=Co,Ni,Mn,etc.)은 우수한 충방전 효율 과 열적 안정성 뿐 아니라 277mAh/g의 높은 이론용량을 갖고 있어 고용량 양극박막으로의 적용시 고용량 박막이차전지 제작이 가능하다. 본 연구에서는 전 고상 박막 전지의 구현을 위하여 RF 스퍼터링법을 사용하여 Li[Li0.2Mn0.54Co0.13Ni0.13]O2 박막을 증착하였다. Li/MnCoNi의 몰 비율을 변화시켜 높은 전기화학적 특성을 갖는 분말을 합성하여 제조한 타겟으로 Pt/TiO2/SiO2/Si 기판위에 RF 스퍼터법을 이용하여 박막을 성장시켰다. 박막 증착 시 가스의 비율은 Ar:O2=3:1로 하고 증착 압력의 조절(0.005~0.02 torr)을 통하여 박막의 두께와 표면 특성을 조절하며 성장시켰다. 또한 박막을 다양한 온도에서($400{\sim}550^{\circ}C$) 열처리하여 결정화도와 전기화학적 특성을 측정하였다. 증착 된 박막의 구조적 특성은 X-ray diffraction(XRD) 과 scanning electron microscopy(SEM)로 관찰되었다. 박막의 전기화학적 특성 평가를 위하여 Cyclic voltammatry를 측정하여 가역성의 정도를 확인하고 WBC3000 battery cycler를 이용한 half-cell 테스트를 통하여 박막의 용량을 평가하였다.

• Journal of the Institute of Convergence Signal Processing
• /
• v.8 no.3
• /
• pp.171-177
• /
• 2007

In this paper, we have designed and implemented an optical signal processor in order to use in a fiber-optic current CT for electric equipments where its properties were discussed. The fabricated optical signal processor is used to reduce a measurement current error that induced by the effects of intensity variation in the optical output signal due to losses coming from optical components or polarization variation in a PFOCS. Also, the optical signal processor was fabricated in compact/lightweight with unification of opto-electronic transducer part, analog signal process part, and real-time measurement part consisted of a level shift and ${\mu}-processor$. The experiment of optical signal processor has been performed in the range of $0{\sim}7,500A$ using the PFOCS made all fiber-optic components. As a result of experiment, the linearity error of measurement current is less than 1.7% and its average error is less than 0.3% in the range of $1,000A{\sim}7,000A$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.694-700
• /
• 1999

In this paper, we studied the design of power divider using the slow-wave effect of Photonic Bandgap structure, which is etched on the ground plane. The proposed PBG structure can provides the changing of the characteristic impedance of the transmission line and the group delay velocity characteristic. Therefore we can make wider width than the width of conventional transmission line and decrease the length of transmission line. We presented the application for power divider using the characteristic impedance and electrical length extracted from scattering parameter. As adding proposed defect units, the effect of defect is studied. The experimental results show good agreements with the simulated results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.863-870
• /
• 2003

The digital transmission system entered in a RF region as digital system use IC chips of the speeder edge rate and clock speed nowadays. Optical path really was used in order to obtain the more capacity. In this paper, we described importance of electrical interconnect to get the signal integrity in optical module by simulation and experiment. 12 channel${\times}$2.5 G/ps optical parallel transmitter modules were manufactured by two different method ; access lines with microstrip and stripline type. We have clearly shown that the optical module adopting microstrip type with S$\sub$11/ $\geq$ -10 dB presents distortion but the optical module adopting stripline type with S$\sub$11/ $\leq$ : 15 dB obtains eye opening in 2.5 Gbis optical eye pattern response.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.8
• /
• pp.765-768
• /
• 2015

In this paper, two ports feeding a microstrip patch antenna using a quadrature hybrid circuit was proposed to enhance the bandwidth for the global positioning system(GPS). The square patch was designed, and the probe feeding was applied. The quadrature hybrid chip circuit for two-port feeding was designed, and output ports that have a 90-degree phase difference feed to the patch antenna. The designed patch and quadrature hybrid circuit were implemented on an FR4 board, and were combined. The measurement of the bandwidth within a voltage standing wave ratio(VSWR) of 2: 1 and axial ratio(AR) in 3dB were 29 %BW(1,230~1,700 MHz) and 15.87 %BW(1,400~1,650 MHz), respectively. The peak gain at the GPS center frequency was measured at 2.75 dBi in an anechoic chamber.