• Resources Recycling
• /
• v.11 no.5
• /
• pp.39-54
• /
• 2002

다케이 세미나는 일본의 기업가 및 학자들로만 구성되어 산화철 및 페라이트분야에 대해 발표 및 허심탄회하게 토의하는 세미나로서 각 기업체간은 상호기술교류 차원에서 많은 참가가 이루어지고 있다. 다케이 세미나의 처음 시작은 다케이 선생의 발상으로 소화 45년(1970년)봄에 제1회 페라이트 하계 세미나 발기인회(회장 다케이 선생, 호시노, 가라자와, 나카무라, 스기모토, 기무라, 오카모토)가 발족되어 매년 7월 3째주 금, 토요일에 페라이트 하계 세미나가 개최되었으며, 지금 현재 제22회를 성황리에 마치고 앞으로도 활발한 연구 활동이 계속 이루어질 것이다. 1930년경 일본의 가토와 다케이가 페라이트에 대한 연구를 독자적으로 수행하여 현재의 페라이트는 기존의 금속 재료에 비하여 전기적 비저항이 훨씬 크기 때문에 우리가 사용하는 전기 제품의 곳곳에 사용되어 지고 있다. 예로 스위칭 전원에 사용되는 트랜스 core, TV와 모니터에 사용되는 편향 core, 로터리 core, 토로이드 core, E·U core, Flyback core등이 사용되고 있다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.1
• /
• pp.41-48
• /
• 2019

This paper deals with the design of the L-band rotary joint, which is a core part of the tracking radar system. The rotary joint is a part that is mounted on the rotating parts of the tracking system antenna, which smoothly transmits RF signals with minimizing signal insertion loss. To improve the insertion loss of rotary joint, 1) dielectric materials, 2) design of distribution ring and 3)dielectric shape are studied. The performance of proposed rotary joint is compared with the conventional product. The prototype rotary joint showed a max insertion loss of 0.68dB, that is improved about 46% compare with conventional product which insertion loss was 1.26dB.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.6
• /
• pp.318-323
• /
• 2009

The lightweight aggregates made of bottom ash (70 wt%) and dredged soil (30 wt%) were prepared to investigate the property differences at various sintering atmospheres. The green aggregates were sintered at $1150^{\circ}C$ and $1200^{\circ}C$ with oxidized, neutralized and reduced atmospheres. The aggregates sintered with oxidized atmosphere showed a clear border between shell and black core area. However, the aggregates sintered with a reduced atmosphere showed only black core area in the entire cross-section of the aggregates. The black core area of the aggregates sintered with a neutralized atmosphere increased with increasing $N_2$ gas flow rates. It was determined that the sintering atmosphere was similar to that of rotary kiln when the CO gas flow was 100 cc/min to make a reduced atmosphere in tube furnace. The water absorption rates of both aggregates from tube furnace with reduced atmosphere and rotary kiln were very similar to each other.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.672-675
• /
• 2006

It is becoming more significant to develop a rotary VCM type actuator for small form factor ODD, as portables are getting more and more popularized nowadays. In this paper, the procedure of development of the actuator which is applicable to compact flash II card and is fit in the specification of BD 1X is explained. This is based on the rotary VCM type actuator, which is good for reducing thickness. Air core solenoid coil is used in order to do focusing mechanism. And the total weight is reduced by using the structure of steel-aluminium-steel triple layer, so, the stiffness is still adequate. Additionally, the tracking coil is moved next to the actuator, so the total length was reduced, then the actuator become applicable to compact flash II card. The force of Magnetic Circuit is improved by using Magnetic Circuit DOE. And flexible mode frequency improved through the DOE of structure part. Modeling was exactly done in consideration of air core solenoid coil and pivot bearing. It is confirmed that the designed model is satisfied with the specification of BD 1X and is applicable to Compact Flash II card.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.143-148
• /
• 2003

In recent years, as the optical Communication systems are developed, the demands of essential parts such as splitter, coupler, WDM, and AWG filter are grow rapidly. The fabrication process for them is not, however, automatic. On that reason, the automation is needed for the grow of productivity. The optical alignment and attach ment is the core process in fabrication. In this paper, the 6-axis rotary stage for multi-channel optical alignment system is developed and the dynamic characteristic of this system is studied.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.4
• /
• pp.160-168
• /
• 2018

Among the components of rotary hooks, a core component of an embroidery sewing system, a study was conducted to apply metal injection molding to the manufacture of a hook body and a housing that was very difficult to mechanical working. The correlation of feedstock, a mixture of binder and SCM 415 metal powder, and properties of the pressure-volume-temperature interrelationship, viscosity, specific heat, and thermal conductivity were measured. Injection molds for the hook body and the housing were developed through injection molding analysis using these properties and conducted injection tests. Optimal injection gate position and number, injection pressure, and injection time were obtained through a comparison of analysis results with the experiment results.

• Tribology and Lubricants
• /
• v.12 no.4
• /
• pp.43-51
• /
• 1996

Rapid increase of refrigeration & air-conditioning system (r & a system) in modem industries brings attention to the urgency of research & development as a core technology in the area. And it is required to the compatibility problem of r & a system to alternative refrigerant for the protection of environment. Then, it is requested to study the lubrication characteristics of refrigerant compressor which is the core technology in the r & a system. The study of lubrication characteristics in the critical sliding component is essential for the design of refrigerant compressor. Therefore, theoretical investigation of the lubrication characteristics of rotary compressor for r & a system is studied. The Runge-Kutta method is used for the analysis of the behavior of rolling piston in the rotary compressor. The results show that the rotating speed of shaft and the discharge pressure have an important effect upon the angular velocity of the rolling piston. This results give important basic data for the further lubrication analysis and design of the rotary compressor.

• Tribology and Lubricants
• /
• v.13 no.1
• /
• pp.62-69
• /
• 1997

Rapid increase of refrigeration and air-conditioning systems 9r & a systems) in modern industries brings attention to the urgency of research & development as a core technology in the area. And it is required to the compatibility problem of r & a systems to alternative refrigerant for the protection of environment. The, it is requested to study the lubrication characteristics of refrigerant compressor which is the core technology in the r & a systems. The study of lubrication characteristics in the critical sliding component is essential for the design of refrigerant compressor. Therefore, theoretical investigation of the lubrication characteristics of rotary compressor for r & a systems is studied. The newton-Raphson method is used for the EHL analysis between vane and rolling piston in the rotary compressor. The results show that the rotational speed of a shaft and the discharge pressure influence significantly the friction force between vane and rolling piston. This results give important basic data for the further lubrication analysis and design of a rotary compressor.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.05a
• /
• pp.7-16
• /
• 1996

Rapid increase of refrigeration & air-conditioning system( r & a system ) in modern industries brings attention to the urgency of development as a core technology in the area. And it required to the compatibility problem of r & a system to alternative refrigerant for the protection of environment. Then, it is requested to research about the lubrication characteristics of refrigerant compressor which is the core thechnology in the r & a system. The study of lubrication characteristics in the critical sliding component is essential for the design of refrigerant compressor. Therefore, theoetical investigation of the lubrication characteristics of rotary compressor for r & a system is studied. And the Runge-Kutta method is used for the analysis of the behavior of rolling piston in the rotary compressor. The results show that the rotating speed of shaft and the discharge pressure have an important effect upon the angular velocity of the rolling piston. This results give important basic data for the further lubrication analysis and design of the rotary compressor.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.127-134
• /
• 2017

A rotary table is a positioning device used in metalworking for the multiple axes of machine tools, and the utilization trend is increasing with machining efficiency. In the construction of a rotary table, the core technology is a power transfer unit that drives the table, typically a gear type and a roller gear cam type. As the rollers installed on the turret column have rolling movement on the contact surface of the roller gear cam, the roller gear cam type has the advantage of low wear, high load, and fast driving. Therefore, it is currently being replaced by a roller gear cam type. In this study, we researched a 5-axis machining method for the roller gear cam on a rotary table and a new method of applying double roller gear cam curve to reduce the noise and shock between the roller and the cam surface. We implemented the 5-axis machining process in this study using software to generate NC-code and machined the roller gear cams using a Mazak Integrex-200IV. We found that the roller gear cam and turret were able to identify mutual touch status and the noise from the operation of the roller gear cam was substantially reduced.