• The Journal of the Acoustical Society of Korea
• /
• v.19 no.2
• /
• pp.33-39
• /
• 2000

We have studied to obtain the frequency characteristics of the Surface Acoustic Wave(SAW) bandpass filter, having low shape factor, it's interdigital transducer(IDT) was formed on the 35° Y-cut X-propagation Quartz substrate and was evaporated by Aluminium. And then, we performed computer-simulation by a simulator. And, we can design that the apodization weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulation. Also, we have employed that the number of pairs of the input and output IDT are 2200 pairs and 1000pairs, respectively and used the Kaiser-Bessel window function in order to minimize the effect of ripple. And, while the width and the space of IDT's finger are 6㎛ m and 5.75㎛, respectively and we could obtain the resonable results when the IDT thickness was 6000Å in consideration of the ratio of SAW's wavelength, and IDT aperture is 2mm. Frequency response of the fabricated SAW bandpass filter has the property that the center frequency is about 70MHz, shape factor is less than 1.3, bandwidth at the 1.5dB is probably 1.3MHz, out-band attenuation is almost -45dB, insertion loss is 19dB and ripple in the width of bandpass is 1dB approximately. Therefore, these frequency characteristics of the fabricated SAW bandpass filter are agreed well with the designed values.

• Journal of Navigation and Port Research
• /
• v.30 no.5 s.111
• /
• pp.331-334
• /
• 2006

In this paper, we designed and fabricated the lowpass filter with the wide stopband characteristics using microp- strip line. Adding the $\lambda_g/4$ open stub at the input and output ports, we developed the L-C ladder type lowpass filter using the open stub which has wide stopband characteristics. In order to reduce the entire size qf this filter, the high impedance microstrip lines were made with the meander structure. The lowpass filter was fabricated with the cutoff frequency 2.3 GHz and its measured frequency responses agree well with the simulation results.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.3
• /
• pp.105-112
• /
• 2007

In general, the earlier methods for the design of MAXFLAT FIR filters have existent problems due to the approximation algorithms used to approach MAXFLAT(maximally flat) response in the passband and the stopband.. The proposed approach advanced by using of MAXSHCUT(maximally sharp cutoff) condition in this paper clearly overcomes these problems. In this approach, we use a key parameter represented with filter-order and cutoff-frequency parameters for obtaining the lowpass filters with the MAXFLAT and MAXSHCUT characteristics in the frequency domain. Consequently, this design technique leads to new MAXFLAT and MAXSHCUT FIR digital filter, which can achieve sharp-cutoff responses with the stopband attenuation exceeding 100 dB almost everywhere.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.5
• /
• pp.463-470
• /
• 2015

In this paper, a new dual-band bandpass filter(BPF) that has resonators and feed lines with Stepped-Impedance Resonator(SIR) structures is proposed. Feed lines with SIR structure provide maximum magnetic field points which occur at the same locations of the input and output feed lines, so the insertion loss of BPF was reduced. Applying the SIR structure to the BPF for the first passband improves rejection characteristics between the first passband and the second passband. It reduces the coupling between the BPF for the first passband and the BPF for the second passband, so it makes the dual-band BPF more compact. The proposed design method provides independent changes of both the center frequency and the bandwidth for each resonator, and also improves filtering characteristics. The validity of the proposed design method is confirmed by comparisons between the designed parameters and the measured results satisfying WLAN specifications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.7
• /
• pp.706-712
• /
• 2004

This paper presents the design technique of output multiplexer(OMUX) for the Ka-band satellite transponder. Output multiplexer consists of low-pass filter(LPF), channel filter and manifold. Channel filters adopt dual-mode technique in design for mass and volume reduction and frequency response of channel filters is 4-pole elliptic response for high frequency selectivity. w-pass filters are designed to be of 13th order corrugated type for high rejection characteristic over reception band of satellite transponder. After initial design of channel filters and manifold, we optimized only a few design parameters for fast and easy optimization instead of optimizing all the design parameter. Measured results of a realized output umltiplexer for Ka-band satellite transponder show good agreement with the computed ones.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.91-99
• /
• 2018

This paper has proposed a low-noise and high-linear RF receiver supporting TV white space from 470 MHz to 698 MHz), which is implemented in $0.13-{\mu}m$ CMOS technology. It consists of a low-noise amplifier, a RF band-pass filter, a RF amplifier, a passive down-conversion mixer, and a channel-selection low-pass filter. A low-noise amplifier and RF amplifier provide a high voltage gain to improve the sensitivity level. To suppress strong and nearby interferers, two RF filtering schemes have been performed by using a RF BPF and a down-conversion mixer. The proposed LPF has been based on the common-gate topology and adopted a bi-quad cell to achieve -24dB/oct characteristics. In addition, the RF receiver can support the overall TV band by controlling a LO frequency. The simulated results show a voltage gain of 56 dB, a noise figure of less than 2 dB, and an out-of-channel IIP3 of -2.3 dBm. It consumes 37 mA from a 1.5 V supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3A
• /
• pp.171-178
• /
• 2003

In this paper, We has proposed two DGS(Defected Ground Structure) resonators and designed the low-pass filter using the proposed DGS types. This structure consists of two rectangular slots, a ‘II type’ slot on the ground plane, and the stub at the transmission line. It has strong advantages that can vary the return loss at the passband freely and also can easily tune the attenuation pole frequency at the stopband. For enhancing the poor skirt property at the cutoff frequency of the Single Stub ‘II Type’ DGS cell, we have obtained the steep slope attenuation characteristic by combining the rectangular slot on both sides of the DGS. This type of the LPF with the proposed structure can be made more smaller than the existing filters and be used to find the various applications for eliminating the hamonics and spurious mode at WLL and the 2.4 GHz ISM band systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.741-747
• /
• 2002

In this paper, NRD guide band pass filter with newly designed inductive iris structure is proposed and analyzed with its test results. In case of common NRD guide filter with air gap coupled structure, it was not easy to fabricate and process or each NRD guide dielectric resonator blocks using PTFE. However, in this our research, each dielectric resonator fabricated in a single NRD guide is coupled with inductive iris located on metal plates. The structure is suitable for mass production of a precise and reliable millimeter-wave filter applications. As a result of measurements, designed NRD guide inductive iris filter has superior performance. The pass band is 38.66~39.06 MHz with 400 MHz bandwidth, insertion loss is about 1.4 dB and return loss is below -18 dB.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.36-36
• /
• 2007

본 논문에서는 SoP-L(System on Package-Laminates) 기술을 이용하여 이종의 유전율을 가진 유기물 적층 기반의 수동소자를 이용한 GSM/DCS 대역 분리용 diplexer를 설계, 제작하였고 그 특성을 고찰하였다. SoP-L 기술은 LTCC기술과 같은 타 SoP 기술과 비교해서 이종의 물질을 접합하는데 용이하고 공정비용이 저렴하다. 이러한 장점을 이용하여 캐때시터는 유전율 40의 고유전율 재료를 사이에 두고 구성하였고, 인덕터 부문에는 유전율 4률 적용, 정방혈 스파이럴 구조로 두 개 층으로 구성하여 소형화를 이룰 수 있었다. 제작 시에 구리와 유기물을 적층, patterning 하였고, 수직 via hole 을 형성하고 구리의 무전해, 전해 도금 과정을 거쳐 각 소자를 연결하였다. 이러한 과정을 거쳐 제작된 diplexer의 GSM 저역 통과 필터는 0.52 dB이하의 삽입손실과 20 dB 이상의 반사손실을 가지고 DCS 통과 대역 부근에 notch 가 존재하도록 설계함으로써 DCS 통과 대역에서 17 dB 이상의 저지특성을 나타내었다. DCS 고역 통과 필터는 1.2 dB 이하의 삽입손실과 16 dB 이상의 반사손실을 가지며 GSM 통과 대역 부근에 notch를 가지도록 설계하여 GSM 통과대역에서 32 dB 이상의 저지특성을 나타내었다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.8
• /
• pp.709-716
• /
• 2016

In this paper, A duplexer module with temperature-insensitive electrical characteristics was proposed for remote wireless communication system. Duplexer modules are required to have performances of low insertion loss, high isolation between transmitted band and received band, harmonic suppression as well as high power durability in the system for transmitting guided information to missile flying a free space on the ground. The proposed duplexer module are consist of transmission bandpass filter and receiving bandpass filter which are connected to common antenna port, planar coupler for output power monitoring and low pass filter for harmonic attenuation of power amplifier and coaxial cavity resonator. The material and dimensions of the resonator are determined for minimum frequency shift by temperature variation using 3D EM simulation. The measured results of the prototype showed a good agreement with the simulation results, and it should be well applied not only for guided weapon systems but also for any other communication systems such as remote radio head.