• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.2
• /
• pp.141-154
• /
• 1993

In this paper, a method to calculate the ultimate compressive strength of welded one-sided stiffened plates simply supported along all edges is proposed. At first initial imperfections such as distortions and residual stresses due to welding are predicted by using simplified methods. Then, the collapse modes of the stiffened plate are assumed and collapse loads for each mode are calculated. Among these loads, the lowest value is selected as the ultimate strength of the plate. Collapse modes are assumed as follows ; (1) Overall buckling of the stiffened plate$\rightarrow$Overall collapse due to stiffener bending (2) Local buckling of the plate part$\rightarrow$Local collapse of the plate part$\rightarrow$Overall collapse due to stiffener yielding (3) Local buckling of the plate part$\rightarrow$Overall collapse due to stiffener berthing (4) Local buckling of the plate part$\rightarrow$Local collapse of the plate part$\rightarrow$Overall collapse due to stiffener tripping. The elastic large deflection analysis based on the Rayleigh-Ritz method is carried out, and plastic analysis assuming hinge lines is also carried out. Collapse load is defined as the cross point of the two analysis curves. This method enables the utimate strength to be calculated with small computing time and a good accuracy. Using the present method, characteristics of the stiffener including torsional rigidity, bending and tripping can also be clarified.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.12
• /
• pp.117-124
• /
• 2007

This study investigates the effect of spatial averaging and compliance taken account of in the analysis of earthquake-induced permanent deformation of slopes. At present, the rigid block analysis originally proposed by Newmark is widely used in the deformation analysis, mainly because of its computational efficiency. This type of approach, however, adopts the so-called decoupled approach, in which seismic response and deformation analyses are carried out separately. Original Newmark block analysis assumes the potential sliding mass to be noncompliant, and has been criticized to be potentially unconservative. This paper reviews the impact of the noncompliance assumption of the potential sliding mass in the Newmark-type analysis. The gross effects of earthquake shaking on the potential sliding mass are estimated by spatial averaging method and analyzed in frequency domain. The results indicate that there is a simple criterion that can be used to determine the level of compliance of the potential sliding mass.

• Geotechnical Engineering
• /
• v.13 no.2
• /
• pp.137-154
• /
• 1997

Piling engineers in limit state design should consider both capacity of a pile and settlements of pile for stability of a structure. This paper analyzes the prediction of the settlements of single piles and nine-group piles installed at an overconsolidated clay site by common prediction methods and cone penetrometer test data obtained closely at pile locations. The effects of Young's modulus, which varies spatially in soil profile, on estimating the set tlements of piles have been investigated briefly. The predicted settlements for single piles and nine-pile group by using simple linear elan tic methods, Vesic's method and Poulos's method, overestimated overalls the measured valroes, and the assumption of Youngs modulus, which are to be varied linearly through the soil layers. did not significantly affect the settlement predictions.

• Geotechnical Engineering
• /
• v.14 no.5
• /
• pp.17-28
• /
• 1998

The design of a ground anchor wall calculating the design anchor force and anchored walls depends primarily on the earth pressure acting on anchored w deflection of the wall, the wall stiffness, distribution exists for anchored walls. In the apparent earth pressure envelope design of anchored walls. In this study, full scale anchored w pressure distribution was obtained from function. Earth pressures obtained from pressure and with the apparent earth pre the anchored wall in sand. It is conclude is appropriate for the anchored wall design.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.2
• /
• pp.131-138
• /
• 2009

Analytical modal verification is considered as the process to provide an acceptable description of the subject structure's behaviour. In general, results of original analytical model are different with actual structure results to uncertainty like non-linearity of material, boundary and modified shape, etc. In this paper, the dynamic model of glider's wing is correlated with static deformation and vibration test results by goal-attainment method, multi-objects optimization technique. The structural responses are predicted by using finite element method and optimization is carried out by using the SQP(sequential quadratic programming) method which is widely used in the constrained nonlinear optimization problem. The MAC(Modal Assurance Criterion) is used to modify the mode shapes and quantify the similarity.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.2
• /
• pp.261-268
• /
• 2018

The study used the simplified flooding analysis model, SIMOD, to distribute the total flood discharge by time, so research on flooding in urban areas can be conducted. The conventional flooding analysis models have limitations in constructing input data and take a long time for analysis. However, SIMOD is useful because it supports rapid decision-making process using quick modeling based on simple hydrological data, such as topography and inflow flood of the study area, to analyze submerged routes formed by flooding. Therefore, the study used the SIMOD model to analyze flooding in urban areas before conducting a comparative study with the outputs from FLO-2D, which is one of the conventional flooding analysis models, to identify the model's applicability. Seongseoje was selected as the study area, as it is located downstream the Geumho river where streams flow in the adjacent areas, and dikes are high enough to apply the "Overflow and Break" scenario for urban areas. With regard to topography, the study applied DEM data for the conventional flooding analysis and DSM data to represent urban building communities, distribution of roads, etc. Input flood discharge was calculated by applying the rectangular weir equation under the bank and break scenario through a 200-year return period of a design flood level. Comparative analysis was conducted in a flooded area with a simulation time of 1-24 hours. The time for the 24-hour simulation in SIMOD was less than 7 minutes. Compared with FLO-2D, the difference in flooded areas was less than 20%. Furthermore, the study identified the need for topography data using DSM for urban areas, as the analysis result that applies DSM showed the influence of roads and buildings.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.1
• /
• pp.29-37
• /
• 2007

A conventional single compartment model cannot simulate reasonably the migration phenomenon of contaminants through unsaturated zone, due to the intrinsic unrealistic assumption of the compartment model that contaminants entering a compartment are immediately and uniformly mixed. Although, a multi-compartments model, in which even physically identical layer is divided into multiple compartments, may be used for explaining the retardation of contaminant mass flux along with increasing number of compartments, its numerical modeling is usually time-consuming and appropriate analytical solutions have not been reported yet. In order to improve the conventional compartment models on contaminant migration through unsaturated zone, a series of analytical solutions for multi-compartments model were derived and a generalized constraint under which the results from multi-compartments model can be simply approximated by single compartment model was proposed. The simplified approximation method was verified by a simple numerical analysis on the constraint under hypothetical conditions. It was also proved that the influent contaminant transfer rate from the bulk unsaturated zone can be generally represented into a time-dependent nominal transfer rate rather than a constant. In addition, the nominal transfer rate turned out to be very sensitive to the contaminant transfer rate between compartments in unsaturated zone, but to be almost insensitive to the transfer rate from contaminated zone. It is expected that the simplified approximation method developed in this study can be used for rapid and reasonable estimation of the migration phenomenon of contaminant through unsaturated zone, instead of time-consuming multi-compartments modeling.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.20-20
• /
• 2017

궤도형 차량의 이동구조는 에너지 소비 측면에서 단점이 있지만 접지압의 감소로 인한 평지 및 야지험지에서도 원활한 주행이 가능한 장점으로 인해 농업분야의 플랫폼에서 많이 사용된다. 곡식을 베는 일과 탈곡하는 일을 한 번에 하는 콤바인도 이러한 무한궤도형 이동구조를 사용한다. 또한 궤도형 차량의 방향전환 및 주행속도 변환은 좌 우 궤도의 회전 속도를 다르게 하여 동시에 제어하기 때문에 정교한 주행 성능을 위해서는 궤도형 차량의 기구학 모델을 고려한 경로 계획이 필요하다. 본 연구에서는 직교형 포장에서 Round harvesting 기법 기반으로 궤도형 차량의 기구학 모델 및 포장정보를 고려한 자율주행 콤바인 경로계획 알고리즘을 개발하고자 하였다. 이를 위해 Labview 기반의 궤도형 차량 시뮬레이션을 구축하여 실제 포장정보를 이용해 생성 된 경로의 적용 가능성을 구명하고자 하였다. 자율주행 콤바인 경로 계획은 콤바인의 길이, 너비, 회전 시 좌 우 궤도의 속도 비, 직진 속도와 회전 속도 비, 회전 각도, 포장의 외부 경계선, 작업 겹침 량, 회경 횟수를 이용하여 좌현 새머리 선회를 포함한 내부 왕복작업 경로를 생성하며 외부 회경 횟수는 2~3회를 가정하였다. 자율주행 시뮬레이션은 차체와 궤도 자체의 미끄러짐과 작동기 지연시간을 단순화 한 궤도형 기구학 모델형태로 구성하였다. 추종 알고리즘은 선견 거리법을 사용하였으며, 측면 변이값과 방향 오차의 선형조합을 이용하여 조향변수를 정의하고 퍼지로직기반으로 좌 우 궤도 속도를 7 단계화하여 조향장치를 모델링하였다. 실험결과 개발 된 경로생성 알고리즘은 실제 취득 된 포장 외부 경계 GPS 위 경도를 이용해 자동으로 생성이 가능하며 간략화 된 콤바인 시뮬레이션에서 직진주행 RMS 위치 오차는 0.05 m, 선회구간에서 직진 구간 진입 시 RMS 위치 오차는 0.11 m, 직진 구간 RMSE 방향 오차는 3.2 deg로 콤바인 예취부 간격인 30 cm보다 작은 위치 오차를 보이며 생성된 경로 전체 추종이 가능함을 나타내었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.58-66
• /
• 1999

The flow characteristics of supersonic ejectors is often subject to compressibility, unsteadiness and shock wave systems. The numerical works carried out thus far have been of one-dimensional analyses or some Computational Fluid Dynamics(CFD) which has been applied to only a very simplified configuration. For the design of effective ejector-pump systems the effects of secondary mass flow on the supersonic ejector flow should be fully understood. In the present work the supersonic ejector-pump flows with a secondary mass flow were simulated using CFD. A fully implicit finite volume scheme was applied to axisymmetric compressible Navier-Stokes equations. The standard two-equation turbulence model was employed to predict turbulent stresses. The results obtained showed that the flow characteristics of constant area mixing tube types were nearly independent of the secondary flow rate, but the flow fields of ejector system with the second-throat were strongly dependent on the secondary flow rate due to the effect of the back pressure near the primary nozzle exit.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.6
• /
• pp.71-80
• /
• 2003

Though a nonlinear time history analysis may be provided to estimate more exactly the seismic performance of building structure, approximation methods are still needed in the aspect of practicality and simplicity, In converting a multi-story structure to an equivalent SDOF system, the mode vectors of the multi-story structure are assumed as the mode shape in elastic state regardless of elastic or elastic-plastic state. However, the characteristics of displacement mode are also changed after the yielding made in the structural elements, because the structure becomes inelastic in each incremental load step. In this research, a method of converting MDOF system to ESDOF system is presented by using nonlinear displacement mode considering the mode change of structures after the yielding. Also, the accuracy and efficiency of the method of the nonlinear displacement mode method of the estimate of seismic response of Mixed Building Structures were examined by comparing the displacements of the roof level of the multi-story building structures estimated from this converted displacement response of ESDOF with the displacement of the roof level through the nonlinear dynamic analysis of the multi-story building structures subjected to an actual earthquake excitation.