• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1249-1253
• /
• 2007

제방은 제내지에 거주하는 인간의 재산과 삶을 방어하고, 홍수를 제어하는 가장 기본적인 수공구조물이다. 제방파괴 원인은 월류, 활동, 침식, 그리고 침투 등으로 분류되어 질 수 있다. 특히 간극수압에 의해 발생하는 침투는 제방 내부침식(internal erosion) 및 파이핑(piping) 등을 야기함으로서 제방파괴를 유도한다. 침투에 의한 제방파괴는 월류나 침식에 의한 제방파괴 유형보다 상대적으로 적으나, 다른 제방파괴 원인을 더욱 활성화 시키는 인자로 작용한다. 도시하천의 경우 높은 치수안전도를 적용하여 제방을 축조함에 따라 월류에 의한 붕괴보다 강우와 하천수의 복합요인에 의한 침투파괴가 중요한 문제로 대두되고 있다. 본 연구에서는 침투와 활동에 대한 안전성을 확보할 수 있는 침투보강기법인 단면확대기법에 대한 적용성 및 유의사항을 수치모의를 통해 검토하였다. 제방 비탈면 경사를 1:2 확대할 경우, 침투유속이 70 %정도 감소되는 것을 확인하였다. 그러나 단면확대기법은 홍수시 통수능과 제내지의 부지 확보 문제 등을 고려하여 적용하여야 하며, 도시하천에서 단면확대기법을 적용하는 데는 일정부분 한계를 가질 것으로 판단된다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.4
• /
• pp.487-497
• /
• 2015

Using existing tunnel for section enlargement and remodeling is being considered as an optimal alternative in order to solve traffic jam in tunnel. The existing method has been performed while blocking the traffic flow. Recently, New enlargement method was developed which can maintain traffic flow during the construction by using protector. It can minimize social loss due to keeping traffic flow. On the other hand, installing and operating protector can cause economic disadvantages. So, social cost estimation considering traffic flow should be considered for relevant economic evaluation of tunnel section enlargement methods. This paper presents the social cost estimation method of tunnel section enlargement methods considering traffic flow. In addition, to compare economic efficiency existing method with new method, suggested method was applied to Maebong Tunnel.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.81-88
• /
• 2018

The present study evaluated the effective arrangement approach of transverse reinforcement in the jacket section for seismic strengthening of reinforced concrete columns. To simulate the full-scale columns, the section dimensions were determined as $450{\times}450mm$ for non-seismic existing columns and $750{\times}750mm$ for section enlargement strengthening columns. Over-lapped channel-shape bars and prefabricated bar units were proposed for closed-hoops in the jacket section, and conventional cross-ties anchored into existing columns and V-ties were considered for the supplementary ties. Test results showed that the axial capacity of the existing column and section enlargement columns with over-lapped channel-shape hoops was similar to the nominal strength calculated using ACI 318-14 procedure whereas the section enlargement column with prefabricated bar units possessed 1.25 times higher axial capacity than the nominal prediction. Furthermore, the axial ductility ratio of the section enlargement column with prefabricated bar unit was 139% higher than that of the existing column despite the potential size effect on ductility of concrete. Thus, it can be concluded that the developed prefabricated bar unit technique is practically useful for preventing the premature buckling of longitudinal reinforcement and confining core concrete in the section enlargement strengthening columns.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.235-242
• /
• 2019

The objective of this study is to modify the mixture proportions of concrete that were developed for section enlargement strengthening elements using a specially designed binder composed of 5% ultra-rapid hardening cement, 10% polymer, and 85% ordinary portland cement in order to assign the self-compaction property to such concrete. The self-compaction abilities of concrete were estimated by the performance criteria specified in JSCE and EFNARC provions. Test results showed that the increase in the unit binder content at the consistent water-to-bider ratio led to increase in viscosity of fresh concrete but did not exhibit the decrease in the fluidity due to a greater viscosity. The mixture proportioning of self-compaction section enlargement concrete could be considered at the following conditions: unit binder contents of $430kg/m^3{\sim}470kg/m^3$ and fine aggregate-to-total aggregate ratios of 40%~46% at the water-to-binder ratio of 38%.

• Railway Journal
• /
• v.16 no.6
• /
• pp.18-24
• /
• 2013

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.6
• /
• pp.143-153
• /
• 2006

The paper presents the results of a study on improvement in flexure capacities of continuous prestressed steel I-girder with section increasement at internal supports. After tensioning, the field experiment on prestressed steel I-girder has been performed in the various aspects of prestressed I-girder introducing section increasement at internal supports, tendon profile.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.12
• /
• pp.81-89
• /
• 2012

The existing tunnel in urban area can be enlarged because of requirement of road-widening by traffic growth. The protector with rectangular cross section can be set up in the tunnel, which will be constructed for enlargement of width, to solve traffic jam around the tunnel. It is impossible to install the rockbolt in the lower area of tunnel due to a limited space between the protector and cutting surface. The objective of this study is to suggest the method of shotcrete thickness increase instead of rockbolt installation in the side wall of tunnel for the stability of tunnel. Numerical analysis was performed to evaluate displacement at the crown of tunnel, convergence of tunnel, and stress in shotcrete lining in 3-lane and 4-lane NATM tunnels enlarged from 2-lane conventional tunnel. There were three types of analysis condition, rockbolt installation, no rockbolt installation, and increase of shotcrete thickness without rockbolt in the side wall of tunnel. There was no difference on the displacement at the crown and the convergence of upper tunnel. In the lower tunnel, the convergence in case of no rockbolt installation was larger as maximum 1.3mm than that in case of rockbolt installation. The stress in shotcrete lining in case of no rockbolt installation was larger as maximum 1.3MPa than that in case of rockbolt installation. Numerical analysis was performed to compare the behavior of shotcrete with rockbolt with that of shotcrete, which its thickness was increased, without rockbolt. The shotcrete has an increase of 20%(250mm ${\rightarrow}$ 300mm, 4-lane tunnel)~25%(200mm ${\rightarrow}$ 250mm, 3-lane tunnel) in its thickness to reduce the stress in shotcrete lining. The behavior of shotcrete lining increased the shotcrete thickness by 20%~25% was similar to that of existing shotcrete lining with rockbolt.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2010.10a
• /
• pp.48-49
• /
• 2010

선박의 러더하부 끝단에서는 선회에 따른 와류로 인하여 선회력 및 후류유동에 변화를 초래한다. 이를 관측하기 위해 NACA단면 형상의 몰수체를 영각과 관측단면을 변화시키며 $Re=2.0{\times}10^4$에서 실험을 통한 순간유동장을 계측 후 그 영향을 조사하였다. 계측된 결과는 상호상관 PIV기법을 이용 Naca단면 끝단에서의 2차원 유동특성을 알아보기 위하여 상호 비교하였다. NACA단면은 영각변화에 따라 후류유동에 영향을 미친다. 동일유입유속에서 영각이 증가함에 따라 관찰단면이 중앙으로 갈수록 와류 규모가 확대되는 것을 관찰할 수 있었다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.6
• /
• pp.637-652
• /
• 2012

The protector with the shape of '${\sqcap}$' in cross section can be set up in the tunnel, which can be constructed for enlargement of cross section, to keep traffic flow in the tunnel. It is impossible to install the rockbolt in the side wall of tunnel due to a limited space between the protector and cutting surface of side wall. The objective of this study is to suggest the optimum thickness of shotcrete lining without rockbolt on the side wall and to evaluate the stability of tunnel enlarged. Numerical analysis was performed to evaluate the displacement at the center of tunnel, the convergence of tunnel, and the stress in shotcrete lining in 4-lane NATM road tunnel enlarged from 3-lane NATM road tunnel. The vertical displacement at the center of tunnel and the convergence of crown in the tunnel with rockbolt in the side wall were almost similar to those in the tunnel without rockbolt in the side wall. The convergence of bench/invert and the stress in shotcrete lining without rockbolt on the side wall were greater maximum 0.57 mm and 1,300 kN/$m^2$ than those with rockbolt in the side wall. The increased convergence and the stress in shotcrete lining can be reduced in incerasing of thickness of shotcrete lining about 20% (5 cm) of standard thickness, 25 cm, of shotcrete lining.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.2
• /
• pp.99-107
• /
• 2018

The objective of the present study is to propose a reliable shape of supplementary V-ties in the section jacketing approach for seismic strengthening of reinforced concrete columns. A total of 24 pull-out specimens were prepared. The test parameters selected with regard to bond strength of V-ties were the shape of V-ties, embedment length of V-tie legs, and compressive strength of concrete. The measured bond strength of V-ties with different shapes were compared with that of the conventional V-ties and predictions using CEB-FIP equation. Ultimately, V-ties with pressed end-details at their legs could be recommended for the supplementary lateral reinforcement of strengthening columns with jacketing thickness less than the embedment length [= max (75mm, $6d_b$)] of conventional V-ties, where $d_b$ is the diameter of the reinforcing bar used for V-ties.