• Korean Journal of Optics and Photonics
• /
• v.4 no.4
• /
• pp.434-441
• /
• 1993

Focusing geometry dependence of output Stokes energy in single pass methane Raman shifter is investigated. The experimental result shows that the threshold energy decreases as confocal parameter increases. This result can be explained by gain suppression caused by Stokes - anti-Stokes coupling. In this paper, we give simple analysis for the focusing geometry dependence of Stokes - anti-Stokes coupling and present the criterion of confocal parameter to reduce the gain suppression. Focusing geometry dependence of stimulated Brillouin scattering is measured and the result is in good agreement with theoretical prediction.

• Korean Journal of Optics and Photonics
• /
• v.12 no.4
• /
• pp.289-293
• /
• 2001

A metal capillary splice fiber-optic sensor was fabricated for use as an intensity-based macro-bending sensor. As the radius of curvature due to the macro-bending decreases, the angular misalignment of the fiber ends inside the metal capillary increases, i.e., the coupling efficiency of the fiber splice is reduced. Thus, macro-bending can be detected by the measurement of the reduction of transmitted power. The detectable range of macro-bending. was measured approximately from 20 mm to 85 mm. The center wavelengths of the fiber Bragg gratings are 1543.3 nm and 1549.5 nm, respectively. The maximum bending loss of this sensor was measured about -11.92 dB. Using this metal capillary spliced fiber sensor and fiber Bragg gratings, macro-bending detection has been demonstrated, and it is shown to have potential for multi-point macro-bending sensors. nsors.

• Korean Journal of Optics and Photonics
• /
• v.24 no.6
• /
• pp.297-310
• /
• 2013

With the explosive growth of internet data traffic due to the FTTH penetration, prevalence of smart devices and cloud network service, the demand for higher bandwidth is ever increasing with the pace of more than 40% annual growth. To accommodate ultra high bandwidth traffic, optical components in each hierarchy have progressed rapidly. WDM has begun to be deployed along with higher bandwidth service in the access network. Next-generation ROADM is under development for efficient network management in the metro network. For long-haul transmission, an advanced modulation scheme based on coherent transmission technology has been adopted to enhance spectral efficiency. In this paper, core components to meet the demands of high speed, high efficiency and low power consumption will be reviewed.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.144-151
• /
• 2013

The KOrea Multi-Purpose SATellite-2 (KOMPSAT-2) is to provide 1.0 m Ground Sample Distance (GSD) panchromatic image and 4.0 m GSD multi-spectral image data for various applications. The KOMPSAT-2 system performs mission applications in the field of earth observations, covering land, sea, coastal zones, and Geographic Information Systems (GIS). The purpose of this document is to compute ground coordinate using satellite position, velocity and attitude data in KOMPSAT-2 and document for work-flow of location accuracy correction in KOMPSAT-2.

• Journal of the Korean Solar Energy Society
• /
• v.23 no.3
• /
• pp.81-91
• /
• 2003

본 연구에서는 복층으로 구성된 $WSio_2Al$ 금속절연체의 상세를 보여주고 있는데, 금속과 절연체의 합성물질은 태양 흡수율의 설계와 열적인 현상을 보여주기 위해 종종 사용된다. 금속의 접착기면 위에 얇은 복층 코팅으로 구성되는 디자인은 태양 스펙트럼의 파장권역에서 선택적 흡수를 위함이다. 본 연구는 태양 복사의 열성능 평가를 위해 금속과 절연체 필름의 방사율, 태양흡수율, 코팅순서, 미 반사층(AR)의 두께, 코팅 두께와 코팅 면수, 전체 코팅 두께 등에 대해 시뮬레이션 하였다. 그 결과 네 겹의 코팅설계에서 $Sio_2AR$ 75 nm 두께와 각각의 층에서 $0.5\sim0.7$의 가변 금속부분 구성이 가장 우수한 성능을 갖는 것으로 나타났다. 또한 시뮬레이션으로 금속과 절연체 합성물의 최적의 구성과 각각의 코팅 두께에 대한 예측이 가능했으며, 최대 태양흡수율은 0.94, 방사율은 0.115의 금속과 절연체의 합성물을 구성할 수 있었다.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.4 no.1
• /
• pp.15-21
• /
• 2005

One of the core technology in WDM-PON system is a generation and modulation technique of the optical source in Optical Network Unit (ONU). In this paper, we propose a reflective semiconductor optical amplifier (RSOA) as a modulator in WDM-PON system. Its performance is analyzed by simulation and actual experimentation. Using RSOA in WDM-PON system as a modulator, it obtains higher gain compared to the conventional SOA due to the double pass gain effect. Furthermore RSOA can provide high gain with comparatively low input power. This is very helpful when we set up the actually system because using lower input power, it can reduce the load of the driving circuit which makes very economical module structure. Therefore, when RSOA is used as a modulator, not only it gives noise suppression effect, but also provides certain amount of gain as well. In addition, comparing with conventional SOA which gives fairly large insertion loss, RSOA can provides more important merits.

• Journal of KIISE:Information Networking
• /
• v.30 no.1
• /
• pp.1-8
• /
• 2003

In this paper. we develop an analytical model to evaluate the virtual topology reconfiguration phase of optical Internet networks. To counter the continual approximation problem brought by traditional heuristic approach, we take the traffic prediction into consideration and propose a new heuristic reconfiguration algorithm called Prediction based Multi-stage Reconfiguration approach. We then use this analytical model to study the different configuration operation policies in response to the changing traffic patterns in the higher layer and the congestion level on the virtual topology. This algorithm persists to decide the optimal instant of reconfiguration easily based on the network state. Simulation results show that our virtual topology management Policy significantly outperforms the conventional one, while the required physical resources are limited.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.455-458
• /
• 2005

옴니(omnidirectional)-PBG(photonic bandgap)의 크기는 쌍을 이루는 광자결정 재료의 고유 굴절률, 충진율 및 두께에 의해 결정되는 것이 일반적이다. 그러나 광자결정체가 다중주기를 가지도록 제작하면 옴니-PBG의 크기를 변화 시킬 수 있다. 본 연구에서는 Si/$SiO_2$를 기본 구조로 하는 광대역 옴니-PBG용 광자결정 구조를 설계, 제작하고 그 특성을 평가 하였다. 각각 단일 주기 $\Lambda_1$(426.9nm) 및 $\Lambda_2$(306.9nm)를 갖는 8N-Si/$SiO_2$ 광자결정에 대해 TE/TM-편광광 $5^{\circ}$ 및 $45^{\circ}$ 입사각에 대한 반사-스펙트라 측정결과는 설계값과 일치하였다. 특히 이중주기 $(8N\cdot{\Lambda}_1+8N\cdot{\Lambda}_2)$를 갖도록 제작된 Si/$SiO_2$ 광자결정은 입사각 $5^{\circ}$의 TE-편광광 반사-스펙트라 측정결과, 약 1050-2500nm의 광대역 파장범위에서 광자 밴드 갭을 보였다.

• Korean Journal of Optics and Photonics
• /
• v.32 no.2
• /
• pp.55-61
• /
• 2021

The lateral-mode characteristics of 850-nm GaAs/(Al,Ga)As multiple-quantum-well laser diodes and their influence on the kinks in output optical power are investigated. For the investigation, self-consistent electro-thermal-optical simulation and measurement of fabricated devices are used. From this investigation, the optimal P-cladding thickness that provides single-lateral-mode operation is determined, so that high beam quality can be achieved even at high output powers.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.3
• /
• pp.400-407
• /
• 1987

Thin film filter type 4-channel wavelength division multiplexing(WDM) device was designed and fabricated for the application in optical subscriber loop system. It has multi-mode fiber pigtails and four wavelength division consisting of 0.81, 0.89, 1.2 and 1.3 um. The evaluated performances are 1-2d B of insertion loss(connector loss excluded)and 30-35d B of crosstalk attenuation for all channels. The performance of the fabricated device was tested in the wideband optical transmission experiment, where the SNR degradation due to the crosstalk of the device was found to be within a measurement error.