• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.2
• /
• pp.243-260
• /
• 2018

A literature review on the effects of high temperature and radiation on radiation shielding concrete in Spent Fuel Dry Storage is presented in this study with a focus on concrete degradation. The general threshold is $95^{\circ}C$ for preventing long-term degradation from high temperature, and it is suggested that the temperature gradient should be less than $60^{\circ}C$ to avoid crack generation in concrete structures. The amount of damage depends on the characteristics of the concrete mixture, and increases with the temperature and exposure time. The tensile strength of concrete is more susceptible than the compressive strength to degradation due to high temperature. Nuclear heating from radiation can be neglected under an incident energy flux density of $10^{10}MeV{\cdot}cm^{-2}{\cdot}s^{-1}$. Neutron radiation of >$10^{19}n{\cdot}cm^{-2}$ or an integrated dose of gamma radiation exceeding $10^{10}$ rads can cause a reduction in the compressive and tensile strengths and the elastic moduli. When concrete is highly irradiated, changes in the mechanical properties are primarily caused by variation in water content resulting from high temperature, volume expansion, and crack generation. It is necessary to fully utilize previous research for effective technology development and licensing of a Korean dry storage system. This study can serve as important baseline data for developing domestic technology with regard to concrete casks of an SF (Spent Fuel) dry storage system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.188-188
• /
• 2000

DLC (Diamond-Like Carbon) 박막은 높은 경도와 가시광선 및 적외선 영역에서의 광 투과도, 전기적 절연성, 화학적 안정성 및 저마찰.내마모 특성 등의 우수한 물리.화학적인 물성을 갖고 있기 때문에 여러 분야의 응용연구가 이루어지고 있다. 이러한 DLC 박막을 제작하는 과정에는 여러 가지가 있으나, 본 연구에서는 ECR-PECVD electron cyclotron resonance plasma enhanced chemical vapor deposition) 방법을 사용하였다. 이것은 최근에 많이 이용되고 있는 방법으로, 이온화률이 높을뿐만 아니라 상온에서도 성막이 가능하고 넓은 진공도 영역에서 플라즈마 공정이 가능한 장점이 있다. 기판으로는 4" 크기의 S(100)를 사용하였고, 박막을 제작하기 전에 진공 중에서 플라즈마 전처리를 하였다. 플라즈마 전처리는 Ar 가스를 150SCCM 주입시켜 5$\times$10-1 torr 의 진공도를 유지시키면서, ECR power를 700W로 고정하고, 기판 bias 전압을 -300 V로 하여 5분 동안 기판을 청정하였다. DLC 박막은 ECR power를 700W. 가스혼합비와 유량을 CH4/H2 : 10/100 SCCM, 증착시간을 2시간으로 고정하고, 기판 bias 전압을 0, -50, -75, -100, -150, -200V로 변화시켜가면서 제작하였다. 이때 ECR 소스로부터 기판까지의 거리는 150mm로 하였고, 진공도는 2$\times$10-2torr 였으며, 기판 bias 전압은 기판에 13.56 MHz의 RF power를 연결하여 RF power에 의해서 유도되는 negative DC self bias 전압을 이용하였다. 제작된 박막을 Auger electron spectroscopy, elastic recoil detection, Rutherford backscattering spectroscopy, X-ray diffraction, secondary electron microscopy, atomic force microscoy, $\alpha$-step, Raman scattering spectroscopu, Fourier transform infrared spectroscopy 및 micro hardness tester를 이용하여 기판 bias 전압이 DLC 박막의 특성에 미치는 영향을 조사하였다. 분석결과 본 연구에서 제작된 DLC 박막은 탄소와 수소만으로 구성되어 있으며, 비정질 상태임을 알 수 있었다. 기판 bias 전압의 증가에 따라 박막의 두께가 감소됨을 알 수 있었고, -150V에서는 박막이 거의 만들어지지 않았으며, -200V에서는 기판 표면이 식각되었다. 이것은 기판 bias 전압과 ECR 플라즈마에 의한 이온충돌 효과 때문으로 판단되며, 150V 이하에서는 증착되는 양보다 re-sputtering 되는 양이 더 많을 것으로 생각된다. 기판 bias 전압을 증가시킬수록 플라즈마에 의한 이온충돌 현상이 두드러져 탄소와 결합하고 있던 수소원자들이 떨어져 나가는 탈수소화 (dehydrogenation) 현상을 확인할 수 있었으며, 이것은 C-H 결합에너지가 C-C 결합이나 C=C 결합보다 약하여 수소 원자가 비교적 해리가 잘되므로 이러한 현상이 일어난다고 판단된다. 결합이 끊어진 탄소 원자들은 다른 탄소원자들과 결합하여 3차원적 cross-link를 형성시켜 나가면서 내부 압축응력을 증가시키는 것으로 알려져 있으며, hardness 시험 결과로 이것을 확인할 수 있었다. 그리고 표면거칠기는 기판 bias 전압을 증가시킬수록 더 smooth 해짐을 확인하였다.인하였다.

• Journal of Science and Technology Studies
• /
• v.2 no.1 s.3
• /
• pp.1-38
• /
• 2002

Recently KISTEP(Korea Institute of Science and Technology Evaluation and Planning) held an open forum for examining 'the Manuscript of National Science and Technology Standard Taxonomic System'. I submitted my opinion letter to the forum because I thought that the matter of setting the standard taxonomic system for Science and Technology is so closely related to the research concern of STS that it needs checking from the viewpoint of STS. This paper primarily focuses on making a criticism of and constructing an alternative to the mamuscript, but it goes so far as to ground the matter upon the STS viewpoint. I propose that we interpret an open forum related to science and technology as an example case of the community of inquiry. Further I try, standing in the context of learning to form a model of doing STS interdisciplinary research. In the context of decision I point out the problem with the 'scale' principle involved in categrizing criteria of the taxonomic system and argue that the problem leads to omitting STS from National Science and Technology Standard Taxonomic System although STS takes up science and technology themselves as its research concern proper. In the context or teaming I seek to set up a typical case study or STS. One of the typical STS research tasks is trying to construct a positive alternative to as well as make a criticism of a given suggestion, for clearer alternatives will, in him, provoke sharper criticisms or safer acceptances. I hope that the model in this paper will exemplify such an alternating procedure of criticism and acceptance.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.6
• /
• pp.123-132
• /
• 2012

Gas sensors has been used very differently that depending on following purposes; Automotive (exhaust gas, fuel mixture gas, oxygen, particulates), agriculture / food industry (fresh, stored, CO2, humidity, NH3, nitrogen oxide gas, organic gas, toxic gas emitted from pesticides and insecticides), industrial / medical (chemical gas, hydrogen, oxygen and toxic gases), military (chemical weapon), environmental measurements (CO and other air pollution consisting of sulfur and nitrogen gas), residential (LNG, LPG, butane, indoor air, humidity). The types of industrial toxic substances are known about 700 species and many of these exist in gaseous form under normal conditions. he multi-gas detection sensors will be developed for casualties that detect the most important and find easy three kinds of gases in marine plant; carbon dioxide(CO2), carbon(CO), ammonia(NH3). Package block consists of gas sensing device minor ingredient, rf front end, zigbee chip. Develope interworking technology between the sensor and zigbee chip inside a package. Conduct a performance test through test jig about prototype zigbee sensor module with rf output power and unwanted emission test. This research task available early address when poisonous gas leaked from large industrial site and contribution for workers' safety at the enclosed space.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.520-520
• /
• 2016

석유 화학공장에서 발생하는 spent sulfidic caustic (SSC) 폐수는 액화석유가스(LPG)나 천연가스(NG)의 정제과정에서 발생되는 것으로 고농도의 sulfide와 cresylic, phenolic 그리고 mercaptan 등이 포함된 독성과 냄새를 유발하는 물질이다. 이러한 물질들은 LPG나 NG의 정제과정에서 높은 산도를 가진 휘발성 황화합 물질들을 제거하기 위해 사용된 NaOH가 $H_2S$와 반응하여 발생하는 것이다. 진한 갈색 또는 검은색을 띄는 SSC 폐수는 12 이상의 높은 pH를 가지고 있으며 5~12 wt%의 높은 염분도를 가지고 있다. 또한 강한 부식성과 독성을 가진 황화합물의 농도가 1~4 wt%이며, 방향족 탄화수소 물질 (i.e. methanethiol, benzene, tolune and phenol)들도 다량 함유되어 있다. 따라서 이러한 유해 물질들은 기존의 하수처리 공정으로 방류하기 전에 완벽하게 처리해야만 하수처리 공정의 오염 부하량을 줄일 수 있다. 습식산화공정은 SSC 폐수를 처리하기 위해 흔히 사용되고 있는 물리-화학적 처리 공정이지만 고비용, 고에너지가 필요하며, 고온 및 고압에서만 작동되어 안전상의 문제점을 갖고 있다. 또한 습식산화공정을 거친 폐수는 배출허용기준을 만족하기 위해 생물학적 2차 처리가 반드시 필요하다. 철-과산화수소를 이용하는 펜톤산화 공정, 그리고 sulfide를 sulfate로 전환시키는 생물학적 처리 공정은 황화합물의 완전한 무기물화가 힘들며, 현장 적용 시 기술적 경제적 부담이 크다. 이러한 단점을 극복하고, SSC 폐수를 효과적으로 처리하기 위해 본 연구는, 높은 흡착력과 광산화력을 가진 흡착광산화 반응 시스템(Adsorption Photocatalysis System, APS)을 개발하였다. APS는 SSC 폐수를 시스템 내부로 유입하여 수중의 오염물질을 흡착광산화제로 구성된 반응구조체가 흡착하고, 흡착된 오염물질을 UV에너지와 이산화티타늄 광촉매의 광화학반응에 의해 최종적으로 무해한 물질로 환원시키는 폐수처리시스템이다. APS의 반응구조체는 태양에너지 및 인공에너지원에 의해 활용 가능하며, 난분해성 유기화합물질을 물과 이산화탄소로 분해할 수 있는 친환경적이고 경제적인 소재로서 널리 쓰이고 있는 이산화티타늄 광촉매와 화력발전소의 높은 소성온도에 의해 연소된 후 발생되는 bottom ash를 이산화티타늄의 지지체로 사용하여 높은 흡착력과 광촉매 산화력을 가진 복합물이다. 개발된 APS에 의해 SSC 폐수를 처리한 결과, COD 86.1%, 탁도 98.4%, sulfide 99.9%의 높은 처리효율을 보여주고 있다. 따라서 본 연구를 통해 개발된 APS는 강한 부식성과 독성 그리고 높은 농도를 가지고 있는 SSC 폐수를 효과적으로 처리할 수 있다.

• Korean Chemical Engineering Research
• /
• v.59 no.3
• /
• pp.417-428
• /
• 2021

The combustion characteristics of anthracite, which follow a complex process with low reactivity, must be considered through the dynamic behavior of circulating fluidized bed (CFB) boilers. In this study, computational fluid dynamics (CFD) simulation was performed to analyze the combustion characteristics of anthracite in a pilot scale 0.1 MW_th Oxy-fuel circulating fluidized bed (Oxy-CFB) boiler. The 0.1MW_th Oxy-CFB boiler is composed of combustor (0.15 m l.D., 10 m High), cyclone, return leg, and so on. To perform CFD analysis, a 3D simulation model reactor was designed and used. The anthracite used in the experiment has an average particle size of 1,070 ㎛ and a density of 2,326 kg/m³. The flow pattern of gas-solids inside the reactor according to the change of combustion environment from air combustion to oxygen combustion was investigated. At this time, it was found that the temperature distribution in air combustion and oxygen combustion showed a similar pattern, but the pressure distribution was lower in oxygen combustion. addition, since it has a higher CO₂ concentration in oxygen combustion than in air combustion, it can be expected that carbon dioxide capture will take place actively. As a result, it was confirmed that this study can contribute to the optimized design and operation of a circulating fluidized bed reactor using anthracite.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.13 no.1
• /
• pp.47-57
• /
• 2003

In this paper, we firstly evaluate the resistance of the reduced 5-round version of the block cipher CIKS-1 against linear cryptanalysis(LC) and show that we can attack full-round CIKS-1 with \ulcorner56-bit key through the canonical extension of our attack. A feature of the CIKS-1 is the use of both Data-Dependent permutations(DDP) and internal key scheduling which consist in data dependent transformation of the round subkeys. Taking into accout the structure of CIKS-1 we investigate linear approximation. That is, we consider 16 linear approximations with p=3/4 for 16 parallel modulo $2^2$ additions to construct one-round linear approximation and derive one-round linear approximation with the probability P=1/2+$2^{-17}$ by Piling-up lemma. Then we present 3-round linear approximation with 1/2+$2^{-17}$ using this one-round approximation and attack the reduced 5-round CIKS-1 with 64-bit block by LC. In conclusion we present that our attack requires $2^{38}$chosen plaintexts with a probability of success of 99.9% and about $2^{67-7}$encryption times to recover the last round key.(But, for the full-round CIKS-1, our attack requires about $2^{166}$encryption times)

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.1
• /
• pp.406-415
• /
• 2021

In this study, a research model was established and analyzed in order to examine how the characteristics of organizational culture affect the innovation behavior of employees. This study divided the characteristics of organizational culture into development, stability, and rationality as sub-factors, and conducted a study on the relationship between characteristics of organizational culture and innovation behavior. This study also attempted to confirm whether creative efficacy mediates between the characteristics of organizational culture and innovation behavior. To this end, the data collection was targeted to 80 members of the organization in the company, and the SPSS and PLS programs were used to analyze the collected data. As a result of hypothesis testing, only stability among the characteristics of organizational culture had a significant direct effect on innovation behavior. These results can be interpreted as meaningful results in a study between the characteristics of organizational culture and the innovation behavior of employees. In addition, creative efficacy was found to significantly mediate the influence of organizational cultural characteristics (development, stability, and rationality) on employees' innovation behavior. We suggest that companies should focus on forming an organizational culture in terms of internal stability perceived by employees, and lead employees' innovation behavior to create organizational performance. We propose that companies should create an organizational culture so that the characteristics of the organizational culture (development, stability, rationality) increase the creative efficacy of the employees and lead to the innovation behavior of the employees.

• KIPS Transactions on Software and Data Engineering
• /
• v.11 no.8
• /
• pp.339-346
• /
• 2022

Recently, the resource depletion and climate change problem caused by the massive usage of fossil fuels for electric power generation has become a critical issue worldwide. According to this issue, interest in renewable energy resources that can replace fossil fuels is increasing. Especially, photovoltaic power has gaining much attention because there is no risk of resource exhaustion compared to other energy resources and there are low restrictions on installation of photovoltaic system. In order to use the power generated by the photovoltaic system efficiently, a more accurate photovoltaic power forecasting model is required. So far, even though many machine learning and deep learning-based photovoltaic power forecasting models have been proposed, they showed limited success in terms of interpretability. Deep learning-based forecasting models have the disadvantage of being difficult to explain how the forecasting results are derived. To solve this problem, many studies are being conducted on explainable artificial intelligence technique. The reliability of the model can be secured if it is possible to interpret how the model derives the results. Also, the model can be improved to increase the forecasting accuracy based on the analysis results. Therefore, in this paper, we propose an explainable photovoltaic power forecasting scheme based on BiLSTM (Bidirectional Long Short-Term Memory) and SHAP (SHapley Additive exPlanations).

• Asia Marketing Journal
• /
• v.8 no.3
• /
• pp.75-99
• /
• 2006

Inje University, a nonprofit-oriented educational institution, was ranked second in the nation and first in all the local universities in the 2001 Comprehensive Evaluation of the Universities in 25 years since it was founded. In order to find out the reason for this high reputation, we had an interview with the chairman and an in-depth interview with other school authorities, interviewed the students and the residents in the community, and collected related data for the second time. We revealed that Inje University had been performing public marketing in the areas of its management philosophy, function, form, and performance. Our interview with the chairman confirmed that Inje University's management philosophy is the frontier spirits that 'contribute to the moor, attracting nobody's attention, in the name of public interest.' It was also revealed that this management philosophy made the function of the university differ from that of the others. Inje University had been focusing on forming a public network for its community, the nation, and the world, not just for its students. Furthermore, we also found out that the university had its unique separate organizations to take care of this business. An excellent on-campus network for the student and the school, a network between off-campus industries, and an international Inje exchange network had been formed. We have concluded that Inje University is a strong nonprofit-oriented hidden champion. The healing art, easily ignored but essential to human beings, and its commitment to education with all its property invested have contributed to Inje University's social status, reputation, and achievements today.