• Membrane Journal
• /
• v.30 no.1
• /
• pp.1-8
• /
• 2020

In membrane bioreactor (MBR), activated sludge degrade the biological component and membrane process separate this bacterial flocks as well the suspended solids. However, membrane fouling is one of the major issues in MBR. In this review, composite membrane used in MBR to overcome fouling is discussed. It is classified into membrane containing carbon and noncarbon materials. Introducing graphene, graphene oxide (GO) and carbon nanotubes or their modified part into pristine membrane enhance hydrophilicity of the composite membrane. Inorganic materials like silicon dioxide (SiO₂) or titanium dioxide (TiO₂) are also incorporated for preparing composite membrane to increase its water flux.

• Journal of Powder Materials
• /
• v.17 no.3
• /
• pp.203-208
• /
• 2010

A new High Frequency Induction Heating (HFIH) process has been developed to fabricate dense $Al_2O_3$ reinforced with Fe-Ni magnetic metal dispersion particles. The process is based on the reduction of metal oxide particles immediately prior to sintering. The synthesized $Al_2O_3$/Fe-Ni nanocomposite powders were formed directly from the selective reduction of metal oxide powders, such as NiO and $Fe_2O_3$. Dense $Al_2O_3$/Fe-Ni nanocomposite was fabricated using the HFIH method with an extremely high heating rate of $2000^{\circ}C/min$. Phase identification and microstructure of nanocomposite powders and sintered specimens were determined by X-ray diffraction and SEM and TEM, respectively. Vickers hardness experiment were performed to investigate the mechanical properties of the $Al_2O_3$/Fe-Ni nanocomposite.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.358-363
• /
• 2014

Adhesion forces between acrylate imprinting resin and a surface treated atomic force microscope (AFM) tip were investigated. Compared to the untreated silicon tip, 38% of the adhesion force is reduced for the hydrophobic tip treated with $CH_4$ plasma whereas 1.6 time increases is found for the hydrophilic tip with $O_2$ plasma treatment. Such a measurement of the adhesion force using AFM provides very quantitative results on adhesion comparing to the crosscut adhesion test which gives qualitative results. Since the adhesion area becomes larger as the imprinting pattern size gets smaller, the surface treatment issue becomes more important in the nano-imprinting process.

• Composites Research
• /
• v.28 no.6
• /
• pp.348-355
• /
• 2015

NDT (Non Destructive Test) of the adhesive joints is very important because their strengths have greatly affected by the worker's skill and environmental condition. Recently, the electric impedance method in which 1-2 wt% CNT was dispersed in the adhesive and the electric resistance of the adhesive joint was measured was suggested for the defect detection of the adhesive joint. The uniform dispersion of CNT in the electric impedance method is very important to make a constant electric resistance of the adhesive joint and the accuracy of defect detection depends on the uniform dispersion. In this paper, the adhesive joints in which CNT was dispersed in the adhesive by the four dispersion methods were made and their electric resistance were measured. The pre-process and evaporation process of CNT using the ultrasonic method and agitation method was used and the effective dispersion method was suggested. Also, the criteria to evaluate the dispersivity was proposed.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.11
• /
• pp.35-40
• /
• 2017

The rearside of concrete lining of tunnels constructed in cold region might experience on freezing due to the low temperature. This causes damage of concrete lining resulting in adverse affect on the durability as well as integrity of tunnel structure by causing damage to the concrete lining. In order to prevent the rearside of tunnel lining from freeing, the temperature change inside the concrete lining was measured by attaching a heating element to the tunnel lining surface and generating heat for a certain period of time. A special freezing chamber was developed to conduct the experiments considering in-situ environment. The carbone nanotube (CNT) was used as a heating element in this study. The temperature distribution of the concrete lining was measured by applying the heat to the heating element. The effect of the outside temperature and heating duration were analyzed.

• Journal of the Korean Magnetics Society
• /
• v.7 no.1
• /
• pp.31-37
• /
• 1997

The magnetoresistance and the saturation field behavior of the Co-Ag nano granular films as a function of the composition and the ferromagnetic underlayer and overlayermaterials were investigated. The maximum magnetoresistance of 23% and the saturation field of 2.3 kOe at room temperature were obtained in the as-deposited 3000$\AA$ $Co_{30}Ag_{70}$ single alloy films. The magnetoresistance and the saturation field of 100$\AA$ $Co_{30}Ag-{70}$ alloy film were 3.65 % and 3.0 kOe respectively. Those of the sandwiched films with 200$\AA$ Fe were 3.3 % and 1.23 kOe respectively. The saturation field of the sandwiched alloy films could be reduced by the exchange coupling between the ferromagnetic layers and the alloy layer. The effective depth of the exchange coupling was approximately 150$\AA$ in each Fe layer. Among the Fe, Co, and FeNi, the most effective materials to reduce the saturation field of the sandwiched alloy films was Fe.

• Elastomers and Composites
• /
• v.42 no.3
• /
• pp.151-158
• /
• 2007

MWNTs have been widely investigated due to unique properties of such as good electrical conductivity and thermal stability in polymer composites industries. This paper established the procedure to fabricate PMMA/MWNT composites by a modular intermeshing co-rotating twin screw extruder with L/D ratio of 42. The electrical properties of PMMA/MWNT composites with different content of MWNT have been investigated. A sheet resistance percolation was observed at 4 wt% of MWNT for the melt processed composites. Sheet resistance of PMMA/MWNT composite film containing 4 wt% of MWNT was nearby $10^4{\Omega}/sq$ and this shows the possibility of potential application to EMI (Electronic Magnetic Interference) shielding materials. The characteristics of composites were analyzed by TGA, DSC, and SEM. In addition, MFI (Melt Flow Index) has been measured to analyze the rheological property.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.77-77
• /
• 2010

그래핀(Graphene)은 한 겹(layer)의 2차원 판상 구조에 탄소원자들이 육각형의 기본 형태로 배열되어 있는 나노재료로서, 우수한 역학적 강도와 화학적, 열적 안정성 및 흥미로운 전기 전자적 성질을 가지고 있는 것으로 알려져 있다. 최근, 이러한 특징적이고도 우수한 물성으로 인하여 기초물성 연구에서부터 차세대 응용까지 고려한 각종 연구들이 활발하게 진행되고 있다. 일반적으로 그래핀을 얻는 방법에는 물리 화학적 박리, 열화학증기증착법(TCVD), 탄화규소의 흑연화, 흑연산화물의 환원 등의 방법들이 알려져 있다. 그 중 TCVD법이 두께의 균일성이 높은 그래핀을 합성하는데 가장 적절한 것으로 알려져 있다. 그러나 TCVD법은 탄소를 포함하는 원료가스를 분해하기 위하여 고온의 공정을 필요로 하게 되지만, 향후 산업적 응용을 고려한다면 대면적 그래핀의 저온합성법 개발은 풀어야 할 시급한 과제로 인식되고 있다. 현재는 메탄을 원료가스로 사용하여 $900^{\circ}C$ 이상에서 그래핀을 합성하는 추세이고, 최근 아세틸렌등의 활성원료가스를 이용하여 $900^{\circ}C$ 이하에서 저온 합성한 연구결과들도 속속 보고되고 있다. 본 연구에서는 고주파 플라즈마를 이용하여 비교적 저온에서 탄소원료가스를 효율적으로 분해하고, 확산플라즈마 영역에 TCVD 챔버를 결합한 하이브리드 화학증기증착법을 이용하여 그래핀의 저온합성을 도모하였다. 원료가스로는 메탄을 사용하였고, 기판으로는 전자빔증착법으로 증착한 니켈 박막 및 구리포일을 사용하였다. 실험결과, 그래핀은 $600^{\circ}C$ 부근의 저온에서도 수 층으로 이루어진 그래핀이 합성된 것을 확인하였다. 합성한 그래핀은 분석의 용이함 및 향후 다양한 응용을 위하여 실리콘산화막 및 투명고분자 기판 위에 전사(transfer)하였다. 합성된 그래핀의 구조평가를 위해서는 광학현미경과 Raman분광기를 주로 사용하였으며, 원자힘현미경(AFM), 주사전자현미경(SEM), 투과전자현미경(TEM) 등도 이용하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.237.1-237.1
• /
• 2013

Ti 와 Al 은 금속간의 화합물이 내산화성에 우수한 성질을 가지고 있으며 낮은 밀도와 고온에도 큰 변화가 없는 성질을 가지고 있다. 그리하여 내식 및 부식 관련 연구나 고온재료를 필요로 하는 우주, 엔진 제품 등에 많은 연구가 진행되고 있다. 또한 Ti-Al-N 박막은 경도가 우수하여 고속 공구 부품에 널리 사용되고 있으며 최근 Ti-Al-N 에 Si 첨가로 인하여 40 GPa 이상의 고경도와 1,000도 이상의 산화온도를 지닌 나노 혼합물 코팅을 형성 시키는 것으로 알려져 있다. 본 연구에서는 Ti, Al, Si 원분말을 PBM (Planetary Ball Milling) 방법을 사용하여 Ti-Al-Si 혼합분말로 제조하고, 제조된 분말들은 SPS (Spark Plasma Sintering) 공정을 통하여 Ti-Al-Si 합금타겟을 제작하였다. 제작된 Ti-Al-Si 합급타겟을 사용한 Sputtering 공정을 수행하여 Ti-Al-Si 3원계 박막을 증착하였다. 그 결과 기존 Ti (82 ${\mu}m$), Al (32 ${\mu}m$), Si (16 ${\mu}m$) 크기의 원분말들이 PBM (Planetary Ball Milling) 공정 후 Ti-Al-Si (18 ${\mu}m$) 로 입도가 작아진 것을 확인 할 수 있었고, 소결 후 타겟이 99% 이상의 높은 밀도를 가졌으며 원분말의 조성과 동일한 조성을 가진 타겟이 제작되었음을 확인하였다. Ti-Al-Si 타겟의 경도는 약 1,000 Hv 이상의 값을 보였으며, Ti-Al-Si-N 박막의 경우 타겟의 조성과 동일하였고 경도는 약 35 GPa 로 높은 경도 값을 가지는 것을 확인하였다. 내산화 테스트 결과 Ti-Al-Si-N 박막은 1,000도 에서도 박막의 손상이 가지 않았다.

• Journal of Adhesion and Interface
• /
• v.20 no.3
• /
• pp.102-109
• /
• 2019

The material constitution of multi-layered thin film coated on the PET base film was analyzed using ATR FT-IR and pyro GC/MS combination. The cross section of the film was acquired by cracking the film after dipping in liquid nitrogen and was observed using optical microscope. Total thickness of the coated film was $70{\mu}m$ and three layers were observed. Since each layers were too thin to analyze directly except the surface layer, analyzable area of each layers were exposed by using a proper solvent and were investigated using ATR FT-IR and pyro GC/MS. Results shows that three layers were commonly consisted of urethane-acrylate copolymers. Also, inorganic and/or metal inclusions detected by XPS and SEM-EDAX were exhibited by nano size $SiO_2$ particles in layer(1) and aluminum flakes in layer(2).