• Clean Technology
• /
• v.27 no.4
• /
• pp.359-366
• /
• 2021

Halloysite nanotubes (HNTs), the multiwalled clay mineral with the composition of Al₂Si₂O₅(OH)₄·nH₂O, have been highlighted as a low-cost adsorbent for the removal of dyes from wastewater. Although a powder of halloysite presents a high specific surface area, forming media are significantly considered due to sludge-clogging induced by the water-bound agglomeration. However, higher firing temperature to achieve the structural durability of the media and lower utilization rate due to longer penetration depth into the media act as hurdles to increase the dye-adsorption capacity. In this work, the retention of the adsorption capacity of halloysite was evaluated with methylene blue solution after the heat treatment at 750 ℃. In order to improve the utilization rate, tubular media were fabricated by extrusion. The images taken by transmission electron microscopy show that HNTs present excellent structural stability under heat treatment. The HNTs also provide superb capacity retention for MB adsorption (93%, 18.5 mg g^-1), while the diatomite and Magnesol^® XL show 22% (7.65 mg g^-1) and 6% (11.7 mg g^-1), respectively. Additionally, compositing with lignin enhances adsorption capacity, and the heat treatment under the hydrogen atmosphere accelerates the adsorption in the early stage. Compared to the rod-type, the tubular halloysite media rapidly increases methylene blue adsorption capacity.

• Journal of Powder Materials
• /
• v.18 no.2
• /
• pp.188-195
• /
• 2011

The aim of this study was to investigate microstructures and mechanical properties of nano-sized Ti-35 wt.%Nb-7 wt.%Zr-10 wt.%CPP composite fabricated by high energy mechanical milling (HEMM) and pulse current activated sintering (PCAS). Grain growth of the mechanically milled powder was prevented by performing PCAS. The principal advantages of calcium phosphate materials include: similarity in composition to the bone mineral, bioactivity, osteoconductivity and ability to form a uniquely strong interface with bone. The hardness and wear resistance property of nano-sized Ti-35 wt.%Nb-7 wt.%Zr-10 wt.%CPP composites increased with increasing milling time because of decreased grain-size of sintered composites.

• Journal of Powder Materials
• /
• v.17 no.3
• /
• pp.203-208
• /
• 2010

A new High Frequency Induction Heating (HFIH) process has been developed to fabricate dense $Al_2O_3$ reinforced with Fe-Ni magnetic metal dispersion particles. The process is based on the reduction of metal oxide particles immediately prior to sintering. The synthesized $Al_2O_3$/Fe-Ni nanocomposite powders were formed directly from the selective reduction of metal oxide powders, such as NiO and $Fe_2O_3$. Dense $Al_2O_3$/Fe-Ni nanocomposite was fabricated using the HFIH method with an extremely high heating rate of $2000^{\circ}C/min$. Phase identification and microstructure of nanocomposite powders and sintered specimens were determined by X-ray diffraction and SEM and TEM, respectively. Vickers hardness experiment were performed to investigate the mechanical properties of the $Al_2O_3$/Fe-Ni nanocomposite.

• Korean Journal of Materials Research
• /
• v.15 no.8
• /
• pp.508-513
• /
• 2005

[ $TiO_2-Fe_2O_3$ ] nanocomposite powders for magnetic photocatalyst were synthesized by sol-gel process, in which $TiO_2$ photocatalytic layer was formed on the surface of $\gamma-Fe_2O_3$ magnetic core. Transmission electron microscopy (TEM) observation and X-ray diffractometry (XRD) analysis revealed that$\gamma-Fe_2O_3$ nanoparticles, $10\~20nm$ in diameter, were coated by $TiO_2$ shell of 5nm in thickness and $TiO_2$ was anatase phase. Also hydroxyl group (-OH) used to decompose organic compounds was detected by Fourier transformation infrared spectrometry(FT-IR) analysis. UV-Visible spectrophotometry results showed that light absorption occurred in the wavelength range of $400\~700 nm$, and the band gap energy $(E_g)$ of powder was 1.8 eV. Finally it was found that the coercivity $(H({ci})$ and saturation magnetization $(M_s)$ of the powder were 79 Oe and 14.8 emu/g, respectively as experimental vibrating sample magnetometer (VSM) measurements.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.33.1-33.1
• /
• 2010

BiFeO3 (BFO)는 강자성과 유전체 특성을 모두 구현할 수 있는 재료로서 연구가 활발히 진행되고 있다. BFO 박막을 제조하는 방법에는 sputtering, chemical solution deposition, pulsed laser deposition methods 등이 알려져 있으나, 이러한 방법들은 근본적으로 고 진공을 사용하거나, 고온에서의 열처리, 낮은 성막 속도 등의 문제점이 있어, 상온에서 비교적 쉽게 박막을 제조할 수 있는 Aerosol deposition에 관한 관심이 증가하고 있다. 본 연구에서는 BFO의 강자성, 강유전 특성을 향상시키기 위해 Ba(Cu1/3Nb2/3)O3 (BCN)를 첨가한 Ba(Cu1/3Nb2/3)O3 (BFO-BCN) 복합재료를 합성하였다. 합성한 마이크론 크기의 입자를 사용하여 나노 결정립 크기의 Ba(Cu1/3Nb2/3)O3 (BFO-BCN) 박막을 상온에서 진공 분말 분사 공정(Aerosol-Deposition)을 이용하여 제조하고, 강자성 및 강유전성 특성을 평가하였다. Aerosol deposition방법으로 제조된 BFO-BCN박막은 BFO박막에 비해 우수한 강자성과 강유전 특성 나타내었다.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.3
• /
• pp.149-154
• /
• 2009

Dense $5Cu_{0.6}Fe_{0.4}-Al_2O_3$ composite was consolidated from mechanically synthesized powders by pulsed current activated sintering method within 1 min. $5Cu_{0.6}Fe_{0.4}-Al_2O_3$ powder was synthesized from 3CuO and 2FeAI using the high energy ball milling. Dense $5Cu_{0.6}Fe_{0.4}-Al_2O_3$ with relative density of up to 95% was produced under simultaneous application of a 80 MPa pressure and the pulsed current. Mechanical properties and grain size of the composite were investigated.

• Journal of Surface Science and Engineering
• /
• v.53 no.4
• /
• pp.153-159
• /
• 2020

Photocatalytic decomposition of polyethylene film with TiO₂ nanotube powders (NTs) was investigated under UV irradiation at ambient conditions. TiO₂ NTs composed of individual nanotubes are prepared by rapid breakdown anodization technique. A comparative study on the photocatalytic decomposition of polyethylene-TiO₂ composite films prepared using TiO₂ nanoparticles (NPs) or TiO₂ NTs (NTs), respectively, was conducted under UV irradiation. Polyethylene film incorporated with TiO₂ NTs showed 26 wt% weight loss after 200 h under UV irradiation about two times faster decomposition rate than TiO₂ NPs which is attributed to large surface area of TiO₂ NTs.

• Korean Journal of Metals and Materials
• /
• v.50 no.12
• /
• pp.961-966
• /
• 2012

Nano-sized Co and $Al_2O_3$ powders were successfully synthesized from $3/4Co_3O_4$ and 2Al by high-energy ball milling. A dense nanocrystalline $2.25Co-Al_2O_3$ composite was consolidated from mechanically synthesized powders by the pulsed current activated sintering (PCAS) method within 2 min. Consolidation was accomplished under the combined effects of a pulsed current and mechanical pressure. A dense $2.25Co-Al_2O_3$ with relative density of up to 95% was produced under simultaneous application of a 80 MPa pressure and a pulsed current of 2800 A. The fracture toughness and hardness of the $2.25Co-Al_2O_3$ composite were $8MPa{\cdot}m^{1/2}$, $870kg/mm^2$, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.2
• /
• pp.65-71
• /
• 2016

In this study, Antimony Tin Oxide (ATO) ion storage layer and $TiO_2$ working electrode were fabricated using Nano Particle Deposition System. NPDS is the cutting-edge technology among the dry deposition methods. Accelerated particles are deposited on the substrate through the nozzle using NPDS. The thicknesses for coated layers were measured and layer's morphology was acquired using SEM. The fabricated electrochromic cell's transmittance was measured using UV-Visible spectrometer and power source at 630 nm. As a result, the integrated electrochromic/DSSC hybrid system was successfully fabricated as an energy harvesting system. The fabricated electrochromic cell was self-operated using DSSC as a power source. In conclusion, the electrochromic cell was operated for 500 cycles, with 49% of maximum transmittance change. Also the photovoltaic efficiency for DSSC was measured to be 2.55% while the electrochromic cell on the integrated system had resulted in 26% of maximum transmittance change.

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.334-339
• /
• 2004

Microstructures and mechanical properties of SPSed monolithic HAp, HAp-Ag, and HAp-ZrO$_2$sintered bodies were investigated by the XRD, SEM, and TEM techniques. The nano-sized HAp powders were successfully synthesized by precipitation of Ca(NO$_3$)$_2$4$H_2O$ and (NH$_4$)HPO$_4$solution. In the HAp-Ag composite, the shrinkage cavities were observed at the interfaces between HAp and large sized Ag particles due to the mismatch of their thermal expansion coefficients. However, no found the defect at the interfaces between HAp and fine-sized Ag particles. In the HAp-ZrO$_2$composite. nano-sized ZrO$_2$particles were almost dispersed at the grain boundaries of HAp phase. The fracture toughness of HAp-Ag and HAp-ZrO$_2$ composites were increased due to the plastic deformation and phase transformation mechanisms of the dispersed fine Ag and ZrO$_2$phase in the HAp matrix, respectively.