• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.12
• /
• pp.547-552
• /
• 2002

In this paper, the path loss in domestic terrain environments for IMT-2000 are measured and considered. Domestic terrain environments are classified and received power is measured at 1.9201GHz. In addition, the Path loss is calculated with consideration of the radiation pattern of antennas based on the results of measurement. For the consideration of path loss in domestic terrain environments, each path loss are fitted with the same slope of a reference model as "COST-231 HATA Urban Model", and then both are compared. As a result, all of the path loss in domestic terrain environments are lower than the path loss of a reference model as "COST-231 HATA Urban Model". We found that a difference of path loss in domestic terrain environments and a reference model is 5dB in urban, 8dB in sparse urban, 12dll in dense suburban, 13dB in suburban, 19dB in sparse suburban, and 29dB in road.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.6
• /
• pp.78-85
• /
• 2009

In time-varying multipath fading channels, orthogonal frequency division multiple access (OFDMA) uplink systems suffer severe performance degradation caused by inter-channel interference (ICI). In this paper, we propose a hybrid interference cancellation (HIC) for suppressing the degradation effect of ICI. The proposed HIC can achieve both exact interference cancellation and low detection complexity through efficient combination of parallel detection and serial cancellation. Simulation results show that, as the effect of Doppler increases, the proposed HIC achieves bit error rate (BER) performance enhancement in compared with severe performance degradation of conventional OFDMA receivers. In addition, both the computational complexity and total detection time are reduced.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.9-14
• /
• 2009

This paper describes measurement of an on-ship power supply noise in mixed-signal integrated circuits. To measure the on-chip power supply noise, we can check the effects of analog circuits and compensate it. This circuit consists of two independent measurement channels, each consisting of a sample and hold circuit and a frequency to digital converter which has a buffer and voltage controlled oscillator(VCO). The time-based voltage information and frequency-based power spectrum density(PSD) can be achieved by a simple analog to digital conversion scheme. The buffer works like a unit-gain buffer with a wide bandwidth and VCO has a high gain to improve resolution. This circuit was fabricated in a 0.18um CMOS technology and has 2.06mV/count. The noise measurement circuit consumes 15mW and occupies $0.768mm^2$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.10
• /
• pp.863-871
• /
• 2017

LMS (least mean square) algorithm widely used in the AVCS (active vibration control system) of helicopters calculates control input using the forward path transfer function and error signal. If the error signal is sinusoidal, it can be represented as the combination of cosine and sine functions with frequency and phase synchronized with the reference signal. The control input also has the same frequency, therefore control algorithm can be simply implemented if the cosine and the sine amplitudes of the control input are calculated and the frequency and phase of the reference signal are used. Calculation of the control input is implemented as simple matrix operation and the change of the control command is slower than the frequency of the error signal, consequently control algorithm can be operated at lower frequency. The signal processing algorithm extracting cosine and sine components of the error signals are modeled using Simulink and PIL (processor-in-the-loop) mode simulation was executed for real-time performance evaluation.

• Journal of the Korea Computer Industry Society
• /
• v.8 no.1
• /
• pp.23-28
• /
• 2007

There are many modern's overwork. excessive drinking, carriage that give stress in muscle by smoking. Because time that sit long by carriage is much. if myalgia beats widower on muscle rheumatism or union formation inflammation, core ache, there is congealment and is painful. Muscle itself is no military register change and rheumatism change shows in areolation of muscle film or muscle nerve sheath etc. that union tissue's inflammation case is around the muscle. It is typical rain joint sex rheumatism. Can assume in case of made work that do not get used to extreme exercise or body perforce. Special quality of do waveform and supersonic waves stimulation processing plant which frequency that is established in research that do Iroin is continued without change is available embodiment according to patient's state variously by series mode through mode frequency waveform, 10 modes, 25 modes, 50 modes etc. Sample that can decide basis standard for supersonic waves through an experiment, low frequency treatment equipment standard for low frequency equipment. supersonic waves treatment equipment that float in city adjusting establishment naturally establish.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.4 no.1
• /
• pp.32-37
• /
• 1979

The corona noise level at the place 10m and the frequency 1MHz from the new 345KV transmission line is 72dB in the maximum rain-fall and 63dB due to the wet conductors. The synthesized corona noise level of all 3 phases dominantly depends on the phase which has maximum corona level among them. The measured characteristic of the variation with distance from the line coincided well with the theoretically calculated value in this paper. The corona noise level was the highest level in rainy weather or snow-fall. It takes a few hours, for the corona noise to be stable after a rain-fall or snow-fall. The measured value of the corona noise level corresponds quite well with the formula for the corona noise level revision. It was necessary to quantize S/N ratio into radio reception quality for the radio interference due to the transmission line. Some regulations for radio reception quality were defined through long term experiments and ratings by ITU, IEEE comittee, NHK in Japan and others. Fixing our own regulation about radio reception quality should be required.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.5
• /
• pp.421-426
• /
• 2017

In this study, we propose a method for predicting the mechanical properties of the printed circuit board (PCB) that has transversely isotropic characteristics. Unlike the isotropic material, there is no specific test standard for acquisition of the transversely isotropic properties. In addition, common material test methods are not readily applicable to that type of laminated thin plate. Utilizing the natural frequency obtained by a modal test and the sizing optimization technique provided in $OptiStruct^{(R)}$, the mechanical properties of a PCB were derived to minimize the difference between test and analysis results. In addition, the validity of the predicted mechanical properties was confirmed by the MAC (Modal Assurance Criteria) value of each of the compared mode shapes. This proposed approach is expected to be extended to the structural analysis for the design verification of the top product that includes a PCB.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.6
• /
• pp.468-475
• /
• 2016

The purpose of this study is to investigate the acoustic problems of the conventional heat recovery ventilator and to suggest the methods of noise reduction from a heat recovery ventilator according to the installed location. The noise level, in this study, was measured and discussed as the parameters of size, wind volume and sound absorbing duct length for a heat recovery ventilator based on domestic and international related standards. It is found, as a result, that almost all of noise levels from the small and medium heat recovery ventilators without the sound absorbing duct in the anechoic chamber were higher than the noise standard value of 50 dB(A) regardless of the wind volume, and the noise levels went down when a sound absorbing duct was installed. In addition, the sound pressure level relative to frequency bands according to the length of sound absorbing duct was generally decreased, as the length of sound absorbing duct in the small and medium heat recovery ventilators was big, and the sound pressure level was generally increased, as the wind volume was great.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.10C
• /
• pp.1000-1010
• /
• 2006

This paper proposes a new architecture for DCT-based motion estimation and compensation. Previous methods do riot take sufficient advantage of the sparseness of 2-D DCT coefficients to reduce execution time. We first derive a recursion equation to perform DCT domain motion estimation more efficiently; we then use it to develop a wavefront array processor (WAP) consisting of processing elements. In addition, we show that the recursion equation enables motion predicted images with different frequency bands, for example, from the images with low frequency components to the images with low and high frequency components. The wavefront way Processor can reconfigure to different motion estimation algorithms, such as logarithmic search and three step search, without architectural modifications. These properties can be effectively used to reduce the energy required for video encoding and decoding. The proposed WAP architecture achieves a significant reduction in computational complexity and processing time. It is also shown that the motion estimation algorithm in the transform domain using SAD (Sum of Absolute Differences) matching criterion maximizes PSNR and the compression ratio for the practical video coding applications when compared to tile motion estimation algorithm in the spatial domain using either SAD or SSD.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.197-200
• /
• 2002

The current Inn technique is many problems that is permission of radio station using RF Wireless Modem, that is influence of geographic obstacle using radio wave, that is frequency interference, that is finiteness of frequency resources. In this paper, we are solved many elements, IM replaces RF Wireless Modem, we suggest transmission technique of correction message using mobile phone, we researched Interface Module development which is linkage of DGPS receiver and mobile phone. IM can transmit correction message passing RS-232 port and modem communication control. IM of base station is initialized RS-232 port and modem to move station for correction message transmission, IM waited response mode. IM of move station is initialized RS-232 port and modem, IM requests hand shaking to base station, completed connection establishment. Users are worked Differential surveying using receiving correction message between mobile phones.