• 한국정밀공학회지
• /
• 제23권9호
• /
• pp.54-60
• /
• 2006

Fitting process carried out in automobile transmission assembly line is classified into three classes; heat fitting, press fitting, and their combined fitting. Heat fitting is a method that heats gear to a suitable range under the tempering temperature and squeezes it toward the outer diameter of shaft. Its stress depends on the yield strength of gear. Press fitting is a method that generally squeezes gear toward that of shaft at room temperature by press. Another method heats warmly gear and safely squeezes it toward that of shaft. Warm shrink fitting process for automobile transmission part is now gradually increased, but the parts (shaft/gear) assembled by this process produced dimensional changes of gear profile in both radial and circumferential directions. So that it may cause noise and vibration between gears. In order to solve these problems, we need an analysis of warm shrink fitting process, in which design parameters are involved; contact pressure according to fitting interference between outer diameter of shaft and inner diameter of gear, fitting temperature, and profile tolerance of gear. In this study, an closed form equation to predict contact pressure and fitting load was proposed in order to develop optimization technique of warm shrink fitting process and verified its reliability through the experimental results measured in the field and FEM, that is, thermal-structural coupled field analysis. Actual loads measured in the field have a good agreement with the results obtained by theoretical and finite element analysis and also the expanded amounts of the gear profile in both radial and circumferential directions are within the limit tolerances used in the field.

• 한국정밀공학회지
• /
• 제23권5호
• /
• pp.37-43
• /
• 2006

Fitting process carried out in automobile transmission assembly line is classified into three classes; heat fitting, press fitting, and their combined fitting. Heat fitting is a method that heats gear to a suitable range under the tempering temperature and squeezes it toward the outer diameter of shaft. Its stress depends on the yield strength of gear. Press fitting is a method that generally squeezes gear toward that of shaft at room temperature by press. Another method heats warmly gear and safely squeezes it toward that of shaft. Warm shrink fitting process for automobile transmission part is now gradually increased, but the parts (shaft/gear) assembled by this process produced dimensional change in both outer diameter and profile of the gear. So that it may cause noise and vibration between gears. In order to solve these problems, we need an analysis of warm shrink fitting process, in which design parameters are involved; contact pressure according to fitting interference between outer diameter of shaft and inner diameter of gear, fitting temperature, and profile tolerance of gear. In this study, an closed form equation to predict contact pressure and fitting load was proposed in order to develop optimization technique of warm shrink fitting process and verified its reliability through the experimental results measured in the field and FEM, that is, thermal-structural coupled field analysis. Actual loads measured in the field have a good agreement with the results obtained by theoretical and finite element analysis and also the expanded amounts of the outer diameters of the gears have a good agreement with results.

• 한국기계가공학회지
• /
• 제20권3호
• /
• pp.40-46
• /
• 2021

An automatic transmission of automobiles enables comfortable driving experience with lower transmission shifting jerks. However, the assembly structure is more complicated and requires additional components with lower efficiency than the manual transmission system. Extensive research has been conducted to improve the overall transmission efficiency by optimizing each component of the automatic transmission assembly. This study focuses on enhancing the friction torque of double angular contact ball bearings used in automatic transmission. The friction torque of the bearing varies with the operating conditions such as the operational load and rotating speed. Since reducing the friction torque of the bearing tends to deteriorate the durability of the bearing, it is necessary to design the bearing having a minimum required friction torque by determining the durability life of an automatic transmission assembly, In this study, the theoretical life and friction torque of conventional and newly-developed bearings are calculated. The difference in the friction torque between the new and existing bearings are also evaluated.

• 한국기계가공학회지
• /
• 제20권5호
• /
• pp.111-120
• /
• 2021

A tractor is an agricultural machine that performs farm work, such as cultivation, soil preparation, loading, bailing, and transporting, through attached working implements. Farm work must be carried out on time per the growing season of crops. As a result, the reliability of a tractor's transmission is vital. Ideally, the transmission's design should reflect the actual load during agricultural work; however, configuring such a measurement system is time- and cost-intensive. The design and analysis of a transmission are, therefore, mainly performed by empirical methods. In this study, a tractor with a measurement system was used to measure the actual working load in the field. Its hydro-mechanical transmission was then analyzed using the measured load. It was found that the velocity factor, load distribution factor, lubrication factor, roughness factor, relative notch sensitivity factor, and life factor affect the gear strength of the transmission. Also, loading conditions have a significant influence on the reliability of the transmission. It is believed that transmission reliability can be enhanced by analyzing the actual load on the transmission, as performed in this study.

• 한국CDE학회논문집
• /
• 제16권4호
• /
• pp.260-267
• /
• 2011

Nowadays, automobile manufacturers are faced with increasing global competition which is required low cost as well as high quality. To reduce shipping and handling cost and delivery time, lots of automobile manufactures tried to build their new factory in the neighborhood of market. Simultaneously, many factories are under construction in developing countries to make efficient use of low-wage workers. However, because systems are installed in developing countries as the same type of domestic facilities, systems have lots of problems such as high installation cost and inefficient use of manpower. To find core problems and generate optimal solution of these problems, thinking process of TOC(Theory Of Constrains) is used. In case of transmission gear machining system, semi-auto system is proposed as the best solution to increase manpower efficiency and system utilization. Semi-auto system consists of automatic machining process and manual transporting process. The system layout is generated based on semi-auto process concept. And, 3D simulation method using QUEST is used to verify production volume of generated system.

• 대한기계학회논문집
• /
• 제8권1호
• /
• pp.86-94
• /
• 1984

본 연구에서는 최신형 슬란트베드(slant-bed)타입의 중절삭용 NC선반주축을 대상으로 하여, 구동방식의 변경-기어변속장치를 주축으로부터 완전히 분리시키고 V벨 트에 의해 구동되는 후로팅방식의 새로운 주촉구조를 설계-을 통하여 고속에서의 주축 의 회전성능 향상을 시도하였고, 실험을 통하여 그 회전성능을 전형적인 3개의 서로 다른 재래식 선반주축모델들의 값과 비교 고찰하였다.

• 한국정밀공학회지
• /
• 제21권2호
• /
• pp.43-51
• /
• 2004

In this paper, the element combination algorithm for designing an arbitrary type of the automatic transmissions is proposed. The powertrain simulation software using this algorithm is then developed. The deliveries of the angular velocities and torques are only considered for the motion characteristics of the automatic transmissions. The effects of the vibration and noise are not considered. The automatic transmission is defined by the basic elements, i.e., planetary gear set, clutch, brake, shaft, general gear, and inertia. The transmission system is defined by the combination of these elements. The element combination matrices automatically generate the equations of motion for each shift. The self error-correcting algorithm is also developed to verify the element combination algorithm. This automotive powertrain simulation/design software with user-friendly graphic user interface has two main modules. The first module, the automatic powerflow generation module, mainly consists of the automatic powerflow and component generation algorithms. This paper covers the theory and application for the first module. The second module deals with the automatic system generation algorithm and will be discussed in the second paper.

• 한국안전학회지
• /
• 제22권5호
• /
• pp.1-6
• /
• 2007

Vibro-impacts in manual transmissions result due to several nonlinearities such as multi-staged clutch characteristics and gear backlashes. For the sake of understanding the torsional system, one specific manual transmission with front engine and front wheel drive configuration is investigated with a linear model under the several assumptions substituting the nonlinear factors. First, this system is examined with the mathematical approaches by expressing the governing equations to find out the torsional motions. Second, this system is analyzed using the linear model in order to understand its modal and frequency response characteristics using eigensolution method and the FRF(Frequency Responses Function) analysis. Third, with the given results from the eigensolutions, several mode shapes are investigated related to the torsional motion characteristics. Fourth, the system characteristics with the FRFs are studied with the basic approach, with which the several key parameters will be suggested based upon the results in the further studies.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제12권3호
• /
• pp.201-213
• /
• 2012

A gear type lubrication pump is an essential component of the powertrain and has a major role for supplying oil to the gears and bearings in automatic transmission with a hydraulic clutch. Therefore, the durability test code design of lubrication pump is very important to ensure the reliability of the entire transmission and the vehicle. In this study, the design process for the life testing of lubrication pump has been generalized by four steps. The four design steps of the life testing of lubrication pump consist of the configuration of load spectrum, rain flow counting and analysis of load level, the equivalent damage assessment and test code generation. In fact, the load spectrum should be obtained from the field operating condition but that kind of data is the top secret of manufacturers. This is not open to the public in general. So we could use the artificially simulated load spectrum instead of field obtained one and focused on the development of the general process for designing the life test of a gear type lubrication pump. Reliability goals for lubrication pump, pressure, torque, temperature and load spectrum, if present, as appropriate for the given test conditions, accelerated life testing for the lubrication pump can be designed by the developed design steps.

• 소성∙가공
• /
• 제20권7호
• /
• pp.485-490
• /
• 2011

The application of helical gears in crucial parts of automotive transmissions has been steadily increasing due to their higher power transfer performance compared to spur gears. However, the traditional gear manufacturing methods such as hobbing and deburring require large cycle times with expensive production lines so that there have been intensive efforts trying to manufacture gears via forging processes. Although forging processes for spur and bevel type gears have been developed on the practical level, the manufacturing of helical gears is still dependent on the traditional cutting process. Therefore, this paper seeks to develop a cold forward extrusion process for the helical gear with the pitch diameter of 43.5mm and a helix angle of $18.4^{\circ}$. A forward extrusion process was used due to the relatively small diameter of the target geometry. The material deforming behavior influenced by the die geometry was examined by using CAE analysis. Finally, it was found that the helical gear manufactured by the developed extrusion process satisfied the dimensional accuracy and mechanical characteristics for automotive transmissions.