• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.6
• /
• pp.25-31
• /
• 2004

In this paper, we introduce kinetic Monte Carlo (kMC) methods for simulating diffusion process in nano-scale device fabrication. At first, we review kMC theory and backgrounds and give a simple point defect diffusion process modeling in thermal annealing after ion (electron) implantation into Si crystalline substrate to help understand kinetic Monte Carlo methods. kMC is a kind of Monte Carlo but can simulate time evolution of diffusion process through Poisson probabilistic process. In kMC diffusion process, instead of. solving differential reaction-diffusion equations via conventional finite difference or element methods, it is based on a series of chemical reaction (between atoms and/or defects) or diffusion events according to event rates of all possible events. Every event has its own event rate and time evolution of semiconductor diffusion process is directly simulated. Those event rates can be derived either directly from molecular dynamics (MD) or first-principles (ab-initio) calculations, or from experimental data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.444-455
• /
• 2019

The purpose of this research was to analyze technological trends of 「Military Small Giant Venture Tech-Fi Net」 from Defense Technology Information Service via social network analysis. 「Military Small Giant Venture Tech-Fi Net」, which was constituted for their fine technology for application to the military field, registered 847 technologies of 388 companies. In this research, we analyzed 847 technologies for the relations between "Military System" and "Military Technology Category" via centrality measurement, one of the social network analysis methods. The results indicate that the major technologies of domestic military small giant venture companies were "Sensor" and "ICT" for "C4I System" and "Surveillance and Reconnaissance System" and "Platform/Structure" for "Land System", "Aeronautical System" and "Naval Sea System". In contrast, we recognized inadequate technologies, such as "Propellant" and "Material" for "Missile and Ammunition system" and "Sensor" and "ICT" for "Defense System", We hope that our results and method will be conducive to the technological development of Small Giant Venture companies.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.4
• /
• pp.230-237
• /
• 2005

The angle-tracking of maneuvering targets is required to the state estimation and classification of targets in underwater acoustic systems. The Problem of angle-tracking multiple closed and crossing targets has been studied by various authors. Sword et al. Proposed a multiple target an91e-tracking algorithm using angular innovations of the targets during a sampling Period are estimated in the least square sense using the most recent estimate of the sensor output covariance matrix. This algorithm has attractive features of simple structure and avoidance of data association problem. Ryu et al. recently Proposed an effective multiple target angle-tracking algorithm which can obtain the angular innovations of the targets from a signal subspace instead of the sensor output covariance matrix. Hwang et al. improved the computational performance of a multiple target angle-tracking algorithm based on the fact that the steering vector and the noise subspace are orthogonal. These algorithms. however. are ineffective when a subset of the incident sources are coherent. In this Paper, we proposed a new multiple target angle-tracking algorithm for coherent and incoherent sources. The proposed algorithm uses the relationship between source steering vectors and the signal eigenvectors which are multiplied noise covariance matrix. The computer simulation results demonstrate the improved Performance of the Proposed algorithm.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.1
• /
• pp.125-133
• /
• 1993

Most studies on the vibration analysis of a beam-column with ends elastically restrained and various intermediate constraints have been based on the Euler beam theory, which is inadequate for beam-columns of low slenderness ratios. In this paper, analytical methods for vibration and dynamic sensitivity of a Timoshenko beam-column with ends elastically restrained and various intermediate constraints are presented. Firstly, an exact solution method is shown. Since the exact method requires considerable computational effort, a Rayleigh-Ritz analysis is also investigated. In the latter two kinds of trial functions are examined for comparisions : eigenfunctions of the base system(the system without intermediate constraints) and polynomials having properties corresponding to the eigenfunctions of the base system. The results of some numerical Investigations show that the Rayleigh-Ritz analysis using the characteristic polynomials is competitive with the exact solutions in accuracy, and that it is much more efficient in computations than using the eigenfunctions of the base system, especially in the dynamic sensitivity analysis. In addition, the prediction of the changes of natural frequencies due to the changes of design variables based on the first order sensitivity is in good agreements with that by the ordinary reanalysis as long as the changes of design variables are moderate.

• Journal of the HCI Society of Korea
• /
• v.7 no.2
• /
• pp.25-34
• /
• 2012

A veterinary student learns and experiences veterinary processes though experiments and practices using real animals. However, animal protection laws regulate animal experiments and restrict number of the experiments on laboratory animals, veterinary students would have less chances of the experiments and the practices for their veterinary training with real animals. This paper proposes a simulator for veterinary education based on augmented reality (AR). We selected an intravenous injection procedure for the simulation because the injection procedure is the most frequently used procedure during veterinary training and the most difficult stage for beginning veterinary students. The proposed AR simulator provides with a tangible prop, of which shape looks like a leg of a real dog. It also has a injection simulator, which receives user's input and sends force feedbacks to indicate results of the injection simulation. We developed a WorkBench type AR system with an LED display and cameras for visual information processing. Finally, we evaluated its performance through experiments and user studies to check its acceptance level and usability of the proposed system. We compared the proposed system with a traditional video based education and an AR based system using a head mounded display (HMD). The results that the proposed system showed better performances over these systems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.455-464
• /
• 2019

The sensorless control based on the flux linkage of PM synchronous motors has excellent position estimation characteristics at low speeds. However, a limitation arises because the integrator of flux estimator is saturated by the DC offset generated during the analog to digital conversion(ADC) process of the measured current. In order to overcome this limitation, HPF with a low cutoff frequency is used. However, the estimation performance is deteriorated (Ed- the verb deteriorate already includes the meaning of 'problem') at high speed due to the low cutoff frequency, and increasing the cutoff frequency of the HPF induces further problems of phase leading and initial starting failure at low speeds. In this paper, the cutoff frequency of HPF was synchronized to the operation frequency of the motor: at low speeds the cutoff frequency was set to low in order to reduce the phase leading of the estimated flux, and at high speeds it was set to high to raise the DC offset removal performance. As a result, the operating range was increased by 200%. Furthermore, a phase compensation algorithm is proposed to reduce the phase leading of the HPF to less than 1.5 degrees over the full operating range. The proposed sensorless control algorithm was verified by experiment with a PM synchronous motor for a washing machine.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.8 no.11
• /
• pp.215-222
• /
• 2018

In this paper, the research on the energy storage system adapting super-capacitor has been performed. The most advanced features compared to the conventional lead-acid battery systems is that it can obtain high power capability due to the super capacitor power characteristics. The suggested system can attain high power in short times and achieve high power quality improvements. The application areas are power quality improvement system, motor start power which requires high power during transient times. The energy conversion system consists of bi-directional converter and inverter and advantages of high speed, high power charging and discharging performances. The design steps for the two loop controller of the bi-directional inverter are suggested and verified by the experiment and manufacturing. The two loop controller design starts from linearized transfer function which is calculated from the state averaging model including state decoupling method. The current controller requirements are 20% overshoot and settling time and voltage controller are no overshoot and settling time which is 10 times longer than current controller. The design is verified from the step input response. The designed controllers have unity power factor characteristics and thus can improve the power quality of the grid. It also has fast response time and zero steady state error.

• Analytical Science and Technology
• /
• v.21 no.2
• /
• pp.148-157
• /
• 2008

To describe the lifetime prediction of gas turbine core parts serviced in some ten thousands rpms at over $1,000^{\circ}C$, the Larson-Miller Creep Curves, which are formed by creep rupture tests as the destructive experiment with parameters of stress and temperature, are used often, but not exact and reliable with errors of over some tens. On the other hand, this study shows a non-destructive method with increased accuracy and reliability. The SEM and TEM specimens were extracted by replica after polishing the local airfoil and root surfaces of the first stage scraped blade (bucket), serviced for 18,000 hours at $1,280^{\circ}C$ in Gas Turbines of Boryong. The observed TEM and SEM precipitates were digitalized for calculation of the average size. Here we could find the precipitate size grown from $0.45{\mu}m$ to $0.6{\mu}m$ during service and the grown precipitates to be still sound. From these results we could conclude that the scraped balde can be used for ten thous and hours additionally and for twenty thousand hours by additional heat treatments on the scraped blade.

• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.87-95
• /
• 2008

One way to shield an atypical structure to secure the occupant safety of an impact vehicle is to stack energy absorbing material modules around the structure. To be applicable to a cushion module, material must have enough energy absorbing capabilities while satisfying the safety requirements of the vehicle occupant. Static compression test of the potential materials gives a good indication which material is good for a slacking module. This paper presents the mechanical properties that a cushion material must have to satisfy the safety requirements. Static tests are performed for Quard-Guard system module, sand bag, recycled tires, Geo-Container, Geo-Cell and Expanded Polystyren (EPS) Blocks. Static test results are discussed and EPS block of $30kg/m^{3}$ density showed good potential for a cushion module. To check the dynamic effect of EPS block, drop tests have been made up to 35.6km/h impact speed. Drop test results are compared with static test results and no appreciable difference was found. To improve the EPS module property, making holes to the block is suggested and drop test are performed for the modified blocks. From the drop test results, design values are suggested.

• Journal of Navigation and Port Research
• /
• v.39 no.3
• /
• pp.209-215
• /
• 2015

Miraculous victory of Myeongnyang sea battle turned the tide of the Joseon's entire war against Japan and it is regarded as one of the most remarkable sea victories in the world history. In the sea battle of Myeongnyang, on September 16, 1597(lunar calender), the Joseon navy with 13 battle ships, led by Admiral Yi Sun-sin, won the Japanese navy with their fleet of 133 warships. There were several reasons why Admiral Yi decided on this location for battle. Myeongnyang strait is so narrow and had currents so powerful that many ships could not pass strait simultaneously. Therefore, despite being vastly outnumbered, Admiral Yi used terrain and tidal current advantage to defeat Japanese navy's numerical advantage. In order to find out the tidal state of Myeongnyang strait on September 16, 1597, topological phase of sun and moon was studied by orbital period of earth and moon. The tidal state of Myeongnyang strait on September 16, 1597 is estimated based on the theories of tide and tide tables. As a result of this study, time of slack water were found to be 0636, 1248, 1906 and time/speed of maximum tidal current were found to be 0930/8.3kts(NW), 1612/9.9kts(SE).