• Economic and Environmental Geology
• /
• v.49 no.6
• /
• pp.459-467
• /
• 2016

Due to the limited areal space for installation, borehole heat exchangers (BHEs) at depths deeper than 300 m are considered for geothermal heating and cooling in the urban area. The deep vertical closed-loop BHEs are unconventional due to the depth and the range of the typical installation depth is between 100 and 200 m in Korea. The BHE in the study consists of 50A (outer diameter 50 mm, SDR 11) PE U-tube pipe in a 150 mm diameter borehole with the depth of 300 m. In order to compensate the buoyancy caused by the low density of PE pipe ($0.94{\sim}0.96g/cm^3$) in the borehole filled with ground water, 10 weight band sets (4.6 kg/set) were attached to the bottom of U-tube. A thermal response test (TRT) and fundamental basic surveys on the thermophysical characteristics of the ground were conducted. Ground temperature measures around $15^{\circ}C$ from the surface to 100 m, and the geothermal gradient represents $1.9^{\circ}C/100m$ below 100 m. The TRT was conducted for 48 hours with 17.5 kW heat injection, 28.65 l/min at a circulation fluid flow rate indicates an average temperature difference $8.9^{\circ}C$ between inlet and outlet circulation fluid. The estimated thermophysical parameters are 3.0 W/mk of ground thermal conductivity and 0.104 mk/W of borehole thermal resistance. In the stepwise evaluation of TRT, the ground thermal conductivity was calculated at the standard deviation of 0.16 after the initial 13 hours. The sensitivity analysis on the borehole thermal resistance was also conducted with respect to the PE pipe diameter and the thermal conductivity of backfill material. The borehole thermal resistivity slightly decreased with the increase of the two parameters.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.11 no.3
• /
• pp.150-159
• /
• 2008

The marine litter generated as by-products of human activities and economic development enters to the sea through rivers or stream Indirectly, and through sea-based activities directly. It is commonly comprised of materials that degrade very slowly, such as various plastic products, polystyrene, glass, rubber, metal, wood, derelict fishing nets, wire, rope and so on. Such litter is found in the water column and on the seafloor as well as coastal areas In the Northwest Pacific region. It causes injury or death of human and other living organisms and also accident or damage of the vessel. It is not only a problem of country but also regional and/or global problem because it is transported by currents and winds from one country to another. In this regard, Northwest Pacific Action Plan (NOWPAP) Marine Litter Activity (MALITA) project had been carried out during 2006-2007 biennium and NOWPAP Regional Action Plan on Marine Litter (RAP MALI) has been also continuously implemented in the 2008-2009 biennium as next phase step of MALITA. MERRAC, one of four Regional Activity Centres (RACs) of NOWPAP, has developed monitoring guidelines, sectoral guidelines, and brochures related to sea-based marine litter and port reception facilities and services through MALITA project. Based upon these output, MERRAC will continuously implement relevant activities of RAP MALI in order to help to establish and improve a regional mechanism to deal with the sea-based marine litter problem. This paper aims to introduce MERRAC activities under MALITA and RAP MALI, and to suggest several recommendations to reduce marine litter in the NOWPAP region.

• Journal of Sericultural and Entomological Science
• /
• v.47 no.2
• /
• pp.51-55
• /
• 2005

Resveratrol is naturally occurring phytoalexin compounds produced by grape berries, peanuts, and their products in response to stress such as fungal infection, heavy metal ions or UV irradiation. The objective of this study was to develope a reliable high performance liquid chromatographic (HPLC) method for the quantitative determination of trans-resveratrol in mulberry fruit. Samples were extracted in 80% MeOH and filtered with $0.45{\mu}m$ syringe filter. The transresveratrol was separated Waters $C_{18}$ column, using a mobile phase containing 0.025% trifluroacetic acid in 5% acetonitril and 0.035% trifluroacetic acid in 50% acetonitril, detected by photodiode array detector (PDA) at 254 nm and the flow rate was 1ml/min. Under this analytical condition, the mean content of mulberry fruits (fifty varieties) was $777.3{\pm}585.9ppm$. Among the tested samples, 'Mansaengbaekpinosang (II)' was the highest level in 3450.6 ppm. However four accessions including 'Gukbu', 'Sabangso (I)', 'Simseol' and yield mulberry fruit were not able to detected. Eight suitable varieties selected for the production of fruit were 'Jeolgokchosaeng (Chungbuk)' 777.8 ppm, 'Dangsang 7' 771.1 ppm, 'Jangsosang' 133.9 ppm, 'Susungppong' 31.1 ppm, 'Suwonnosang' 639.7 ppm, 'Palcheongsipyung' 1475.9 ppm, 'Kangsun' 864.0 ppm, and 'Jukcheonchosaeng' 1458.5 ppm. 'Daesungppong' which was the first authorized variety for the production of mulberry fruit was 1236.7 ppm. In conclusion, these results suggest that mulberry including fruit and leaf may a good new resource for resveratrol production.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.3
• /
• pp.225-235
• /
• 2009

A common procedure of restoration of endodonticlly treated tooth with fiber-reinforced post is followed by core build-up after post cementation. However, this technique is complex and time-consuming. The aim of this study was to compare fracture strength of premolar, restored with various methods of core fabrications on fiber-reinforced posts and casting metal restoration. Forty five freshly extracted human mandibular premolars were obtained and devided into 5 groups acconding to the type of post and methods of core build-up. In Group A, D.T. $Light-post^{(R)}$ were cemented with $DUO-LINK^{TM}$ and then $LIGHT-CORE^{TM}$ was used for core restoration. In Group B, D.T. $Light-post^{(R)}$ and $DUO-LINK^{TM}$ were used for cementing in the postspace, and $DUO-LINK^{TM}$ was used again for core restoration. In Group C, $Light-post^{(R)}$ bonding and the core build-up were performed simultaneously by using $DUO-LINK^{TM}$. In Group D, $LuxaPost^{(R)}$ was bonded by using $LuxaCore^{(R)}-Dual$. Again, $LuxaCore^{(R)}-Dual$ was used for core restoration. In Group E, $LuxaPost^{(R)}$ bonding and the core build-up were performed simultaneously by using $LuxaCore^{(R)}-Dual$. Axial reduction was formed parallelly as possible and 45 degree bevel was made at buccal occlusal surface. Crowns were fabricated and cemented. Each tooth was embedded in self-curing acrylic resin to the level of 2mm below the CEJ. Specimens were fixed on universal testing machin such that the axis of the tooth was at 45 degree inclination to the horizontal plane, and compressive force was applied at a crosshead speed of 1mm/min until failure occurred. The mean fracture strength was the highest in group A followed by descending order in group B, D, E and C. However, there were no statistically significant differences between groups with regard to the fracture strength. The type of the post or build-up methods of the core does not seem to influence the fracture strength.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.3
• /
• pp.241-251
• /
• 2010

This study aims at contributing to the restorative dentistry by examining results in the vertical load test of four different low invasive fixed partial dentures. Based on a hypothesis on the right upper first molar is missing, three units of FPDs were made for the second premolar and the second molar abutment. that is, twelve metal dies and FPDs were made for resin bonded FPD and Two Key Bridges and Human Bridge without occlusal rest and Human Bridge with occlusal rest. By using universal test machine, the numerical maximum value were recorded during the vertical load test of each FPDs after the bonding process treated by Maxcem which is resin cement. The failure process and its result of prosthesis were also observed. The maximum load was 7,295 N, 4,729 N, 2,190 N, 3,073 N from groups of resin bonded FPD, Two Key Bridge, Human Bridge without occlusal rest and Human Bridge with occlusal rest respectively. There was a statistical significance among the groups of resin bonded FPD, Two Key Bridge and Human Brides. However, there was no significant difference between Human Bridge without occlusal rest and Human Bridge with occlusal rest. Regarding the failure of prosthesis, the groups of Resin Bonded FPD and Two Key Bridge showed that one of the abutment teeth in the both side of retention part was highly failed earlier than the other one (83.2% and 66.6% respectively). While, Human Bridge without occlusal rest and Human Bridge with occlusal rest showed high percentage of failure in the abutment teeth in the both side of retention part at the same time (91.6% and 58.3% respectively). This study demonstrates that the group of Human Bridges has low resistance to the vertical loads of low invasive FPDs in comparison with the groups of resin bonded FPD and Two Key Bridge. Nevertheless, the maximum occlusal load of the restorative position, resistance to diverse restoration failure, amount of tooth reduction and patients' cooperation should be considered when they are applied in the clinic in order to choose an appropriate restoration for each patient.

• Progress in Medical Physics
• /
• v.19 no.2
• /
• pp.102-112
• /
• 2008

We developed a high-resolution micro-CT system based on rotational gantry and flat-panel detector for live mouse imaging. This system is composed primarily of an x-ray source with micro-focal spot size, a CMOS (complementary metal oxide semiconductor) flat panel detector coupled with Csl (TI) (thallium-doped cesium iodide) scintillator, a linearly moving couch, a rotational gantry coupled with positioning encoder, and a parallel processing system for image data. This system was designed to be of the gantry-rotation type which has several advantages in obtaining CT images of live mice, namely, the relative ease of minimizing the motion artifact of the mice and the capability of administering respiratory anesthesia during scanning. We evaluated the spatial resolution, image contrast, and uniformity of the CT system using CT phantoms. As the results, the spatial resolution of the system was approximately the 11.3 cycles/mm at 10% of the MTF curve, and the radiation dose to the mice was 81.5 mGy. The minimal resolving contrast was found to be less than 46 CT numbers on low-contrast phantom imaging test. We found that the image non-uniformity was approximately 70 CT numbers at a voxel size of ${\sim}55{\times}55{\times}X100\;{\mu}^3$. We present the image test results of the skull and lung, and body of the live mice.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.20 no.3
• /
• pp.113-120
• /
• 2014

Packaging has played important function on marketing as a silent salesman. As an interface of consumer and products, packaging fulfills several functions such as protection, sales promotion, communication and convenience during the distribution process. For the appearance of self-service sales method, packaging could be regarded as important salesman influencing consumers' preference on shelf in the shop. In this study, Vitamin water was selected as the proper target product for lower impact of prices and brands. With previous studies, Vitamin water packaging elements were classified as 'packaging material', 'packaging shape', 'label color', 'logo layout', then each packaging element was consist of details. To measure the influence of each packaging element on consumers' preference quantitatively and to minimize respondent's subjective judgment, Analytic Hierarchy Process (AHP) was used as a tool. Through AHP result, packaging element of the most influence on consumers' preference is 'label color (0.370)', and 'container shape (0.246)', 'container material (0.230)', 'logo layout (0.154)' was in order. Among the detail packaging element, 'plastic (0.405)' has the greatest influence in 'container material' and 'cylinder (0.423)' in 'container shape', 'magenta (0.329)' in 'label color', 'vertical layout (0.572)' in 'logo layout'.

• Journal of the Korean Society of Radiology
• /
• v.5 no.2
• /
• pp.93-96
• /
• 2011

Currently, the development of direct conversion radiation detector using photoconductor materials is progressing in widely. Among of theses photoconductor materials, mercuric iodide compound than amorphous selenium has excellent absorption and sensitivity of high energy radiation. Also, the detection efficiency of signal generated in photoconductor film varies by electric filed and geometric distribution according to top-bottom electrode size. Therefore, in this work, the x-ray detection characteristics are investigated about the size of top electrode in $HgI_2$ photoconductor film. For sample fabrication, to solve the problem that is difficult to make a large area film, we used the spatial paste screen-print method. And the sample thickness is $150{\mu}m$ and an film area size is $3cm{\times}3cm$ on ITO-coated glass substrate. ITO(Indium-Tin-Oxide) electrode was used as top electrode using a magnetron sputtering system and each area is $3cm{\times}3cm$, $2cm{\times}2cm$ and $1cm{\times}1cm$. From experimental measurement, the dark current, sensitivity and SNR of the $HgI_2$ film are obtained from I-V test. From the experimental results, it shows that the sensitivity increases in accordance with the area of the electrode but the SNR is decreased because of the high dark current. Therefore, the optimized size of electrode is importance for the development of photoconductor based x-ray imaging detector.

• Journal of Conservation Science
• /
• v.27 no.3
• /
• pp.333-344
• /
• 2011

Cleaning of foreign matter and corrosion products on surface among conservation treatment of iron artifacts is an important part for looking up a original form. The sand blaster is the most popular equipment when it removes the foreign matter and corrosion products on iron artifacts surface. Current foreign matter and corrosion products equipment, which mostly uses, is sand blaster. Glass dust which sprayed from sand blaster is harmful and causing environmental pollution. In order to solve these problems, we investigated the $CO_2$ snow cleaning that use a eco-friendly equipment to apply for cleaning foreign matter and corrosion products on surface of iron artifacts. It examined by using sand blaster and $CO_2$ snow cleaning to aged steel coupon and iron artifacts. In case of aged steel coupon, the result showed that the sand blaster and $CO_2$ snow cleaning methods were similar to the degrees of cleaning foreign matter and corrosion products, through surface roughness, color measurement and SEM. $CO_2$ snow cleaning applied to aged steel coupons weren't worn out the surface in comparison with sand blaster by SEM. When applied to the iron artifacts, power nozzle of the $CO_2$ snow cleaning was an excellent cleaning effect that surface wern't worn out in comparison with sand blaster. And, it showed that internal structure change of metal was no found before and after cleaning by X-ray radiography. Consequently, we confirmed that cleaning of the sand blaster and power nozzle of $CO_2$ snow cleaning were similar to the effect. But, it's very careful to use this method because of high outlet pressure of power nozzle for applying to the iron artifacts. As a result of experiments, it could be found that the cleaning methods should be selected depending on internal state of the artifacts.

• Food Science and Preservation
• /
• v.21 no.2
• /
• pp.276-285
• /
• 2014

The purpose of this study was to develop a new fermented product (named as Cheonggeumjang) using Sigumjang, Cheonggukjang and Oak mushroom. This study was conducted to evaluate the effects of Sigumjang, Cheonggukjang, and Cheonggeumjang, which were mixed in a different ratio as A (Sigumjang: Cheonggukjang = 1:2), B (Sigumjang: Cheonggukjang = 1:1) and C (Sigumjang: Cheonggukjang = 2 : 1). Then, the functions and physicochemical properties of products were investigated. We found that the crude protein content in Cheonggeumjang was higher than in Sigumjang whereas fat and calories content was less than that of Cheonggukjang. Free sugar content in Cheonggeumjang C 5.8681 g/100g was the highest. Moroever, Cheonggeumjang C and Sigumjang has an antioxidant activities. The electron donating capacity, SOD like activity and the inhibitory effect on xanthine oxidase of these two were significantly high than other group. Fat rancidity is promoted in the presence of metal ion, Cheonggeumjang group has higher inhibitory effect on $Fe^{2+}$ion than on $Cu^{2+}$ ion. The rancidity of fat is also increased by reactive oxygens species, Cheonggeumjang group inhibited $H_2O_2$ in higher extent than $KO_2$. Also, ${\alpha}$-glucosidase inhibition activity of Cheonggeumjang C in all of the concentrations (300 ppm, 500 ppm and 700 ppm) is higher than other groups. In sensory evaluation, Cheonggeumjang C groups is ranked significantly higher than the other groups while considering color, flavor, taste and the overall acceptability. Taken together, the results of this study suggest that Cheonggeumjang is best ingredient for increasing the consumer acceptability and functionality.