• Journal of Powder Materials
• /
• v.31 no.2
• /
• pp.163-168
• /
• 2024

As the demand for lithium-ion batteries for electric vehicles is increasing, it is important to recover valuable metals from waste lithium-ion batteries. In this study, the effects of gas flow rate and hydrogen partial pressure on hydrogen reduction of NCM-based lithium-ion battery cathode materials were investigated. As the gas flow rate and hydrogen partial pressure increased, the weight loss rate increased significantly from the beginning of the reaction due to the reduction of NiO and CoO by hydrogen. At 700 ℃ and hydrogen partial pressure above 0.5 atm, Ni and Li₂O were produced by hydrogen reduction. From the reduction product and Li recovery rate, the hydrogen reduction of NCM-based cathode materials was significantly affected by hydrogen partial pressure. The Li compounds recovered from the solution after water leaching of the reduction products were LiOH, LiOH·H₂O, and Li₂CO₃, with about 0.02 wt% Al as an impurity.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.1
• /
• pp.44-48
• /
• 2000

Amorphous $V_2O_5$ cathode thin films were prepared by DC-magnetron sputtering at room temperature and the thin film rechargeable lithium batteries were fabricated with the configuration of $V_2O_5/LIPON/Li$ using sequential ex-situ thin film deposition techniques. The electrochemical characteristics of $V_2O_5$ cathode materials Prepared at 80/20 of $Ar/O_2$ ratio showed high capacity and cycling behaviors by half cell test. LIPON solid electrolytes films were prepared by RF-magnetron sputtering using the self-made $Li_3PO_4$ target in pure $N_2$ atmosphere, and it was very stable for lithium contact in the range of 1.2-4.0 V vs. Li. Metallic lithium were deposited on LIPON electrolyte by thermal evaporation methode in dry room. Vanadium oxide based full cell system showed the initial discharge capacity of $150{\mu}A/cm^2{\mu}m$ in the range of $1.2\~3.5V$.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.2
• /
• pp.95-100
• /
• 2012

$LiFePO_4$ is an attractive cathode material due to its low cost, good cyclability and safety. But it has low ionic conductivity and working voltage impose a limitation on its application for commercial products. In order to solve these problems, the iron($Fe^{2+}$)site in $LiFePO_4$ can be substituted with other transition metal ions such as $Mn^{2+}$ in pursuance of increase the working voltage. Also, reducing the size of electrode materials to nanometer scale can improve the power density because of a larger electrode-electrolyte contact area and shorter diffusion lengths for Li ions in crystals. Therefore, we chose electrospinning as a general method to prepare $Li[Fe_{0.9}Mn_{0.1}]PO_4$ to increase the surface area. Also, there have been very a few reports on the synthesis of cathode materials by electrospinning method for Lithium ion batteries. The morphology and nanostructure of the obtained $Li[Fe_{0.9}Mn_{0.1}]PO_4$ nanofibers were characterized using scanning electron microscopy(SEM). X-ray diffraction(XRD) measurements were also carried out in order to determine the structure of $Li[Fe_{0.9}Mn_{0.1}]PO_4$ nanofibers. Electrochemical properties of $Li[Fe_{0.9}Mn_{0.1}]PO_4$ were investigated with charge/discharge measurements, electrochemical impedance spectroscopy measurements(EIS).

• Journal of the Korean Electrochemical Society
• /
• v.15 no.1
• /
• pp.27-34
• /
• 2012

$Li_3V_2(PO_4)_3$/carbon composite materials are synthesized from a sucrose-containing precursor. Amorphous $Li_3V_2(PO_4)_3/C$ (a-LVP/C) and crystalline $Li_3V_2(PO_4)_3/C$ (c-LVP/C) are obtained by calcining at $600^{\circ}C$ and $800^{\circ}C$, respectrively, and electrochemical performance as the negative electrode for lithium secondary batteries is compared for two samples. The a-LVP electrode shows much larger reversible capacity than c-LVP, which is ascribed to the spatial $Li^+$ channels and flexible structure of amorphous material. In addition, this electrode shows an excellent rate capability, which can be accounted for by the facilitated $Li^+$ diffusion through the defect sites. The sloping voltage profile is another advantageous feature for easy SOC (state of charge) estimation.

• Membrane Journal
• /
• v.26 no.5
• /
• pp.337-350
• /
• 2016

Lithium-ion rechargeable batteries (LIBs) have garnered increasing attention with the rapid advancements in portable electronics, electric vehicles, and grid-scale energy storage systems which are expected to drastically change our future lives. This review describes a separator membrane, one of the key components in LIBs, in terms of porous structure and physicochemical properties, and its recent development trends are followed. The separator membrane is a kind of porous membrane that is positioned between a cathode and an anode. Its major functions involve electrical isolation between the electrodes while serving as an ionic transport channel that is filled with liquid electrolyte. The separator membranes are not directly involved in redox reactions of LIBs, however, their aforementioned roles significantly affect performance and safety of LIBs. A variety of research approaches have been recently conducted in separator membranes in order to further reinforce battery safeties and also widen chemical functionalities. This review starts with introduction to commercial polyolefin separators that are currently most widely used in LIBs. Based on this understanding, modified polyolefin separators, nonwoven separators, ceramic composite separators, and chemically active separators will be described, with special attention to their relationship with future research directions of advanced LIBs.

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.112-116
• /
• 2018

In this study, the mixing characteristics of water glass and additives (Si, alkali metal), which are one of the main raw materials of silicate based binder used in the production of molds during casting process, were examined. Molecular structures of water glass, additives and mixtures were analyzed FT-IR and viscosity measurements and their correlation were compared. The addition of Si source to the water glass accelerated the Si networking in the material and increased the viscosity. When the alkali metal was added, the viscosity of the water glass decreased by suppressing the Si networking of the water glass. Viscosities of the water glass and lithium silicate (LS) mixtures increased when the content of LS was less than 20 wt% and gradually decreased when the content was more than 20 wt%. By adding KOH to the water glass, the viscosity could be lowered and it could be used effectively to mix with colloidal silica (CS) or potassium methyl siliconate (PMS).

• 한국전기화학회:학술대회논문집
• /
• 2003.11a
• /
• pp.169-176
• /
• 2003

• Journal of the Korean Electrochemical Society
• /
• v.14 no.4
• /
• pp.239-244
• /
• 2011

In this study, $Fe_3O_4$/graphene and CuO/graphene composites were synthesized by the polyol reduction method using ethylene glycol, and their performances as the anodes of lithium ion batteries were evaluated. The physical characteristics of the synthesized composites were analyzed by SEM, XRD, and TGA. In addition, their electrochemical properties were examined by the electrochemical analysis techniques such as charge/discharge performance, cyclic voltammetry, and AC impedance spectroscopy. The cells composed of $Fe_3O_4$/graphene and CuO/graphene composites showed better performance than the graphene electrode, due to the dispersion of nanosized $Fe_3O_4$ or CuO on the surface of graphene and the formation of good electrical network in the electrode. Their composites kept the reversible capacity more than 600 mAh/g even after the charging/discharging of 30 cycles.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.3
• /
• pp.239-244
• /
• 2009

This paper aims to report the effect of surface treatment on graphite and its effect on the improvement of $Al_2O_3$ and $nano-Li_4Ti_5O_{12}$. The structure and property of surface treatment on graphite were determined by scanning electron microscopy, transmission electron microscopy and electrochemical property and safety were determined by charge/discharge cycler, accelerating rate calorimeter. The composite with different metallic oxide exhibited the first efficiency of 82.5% and specific capacity of 350 mAh/g. Although the composite showed same efficiency and specific capacity at first cycle, surface treatment on graphite by $nano-Li_4Ti_5O_{12}$ exhibited a higher charge/discharge rate, cycle life and thermal stability.

• Transactions of the Korean hydrogen and new energy society
• /
• v.14 no.1
• /
• pp.46-52
• /
• 2003

유황 양 전극과 액체 전해질, 리튬 금속을 음극으로 사용한 리튬 유황 전지를 제조하여 그 특성을 조사하였다. 유황 전극은 유황파우더와 carbon black 을 도전재로, 그리고 바인더로 PVdF를 사용하여 제조하였다. 이렇게 제조된 셀은 두개의 다른 전압 구간에서 충방전 실험을 행하였다. 첫 번째 셀은 $S_8+{\chi}Li{\leftrightarrow}Li_2S_x(X=4{\sim}12)$ 반응만을 일어나 게 하기 위하여 2.1V 와 2.5V 사이에서, 그리고 두 번째 셀은 $Li_2S_x+{\chi}Li{\leftrightarrow}Li_2S(x=2{\sim}4)$의 반응만을 일어나게 하기 위하여 1.5V 와 2.5V 에서 충방전 하였다. 그 결과 첫 번째 셀이 더 좋은 싸이클 특성을 가지는 것을 확인 탈 수 있었다. 각 전압구간에서 각 셀이 충방전 되는 동안, 전해질 내로 녹아난 유황의 양은 큰 차치가 없는 것을 확인하였다. 그리고, 전압에 따른 전극의 임피던스를 측정한 결과, 방전이 끝난 후 큰 저항성분이 새로 생긴 것을 확인 할 수 있었다. 이는 사이클이 진행된 후의 전극표면을 SEM 분석을 행한 결과로부터 사이클이 진행된 후 전극 표면에 최종 반응 산물인 $Li_2S$ 가 피막형태로 형성된것을 확인 할 수 있었다.