• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.9-17
• /
• 2005

The aeroelastic stability enhancement of composite hingeless rotor system through the structural damping increase has been investigated. In order to increase structural damping of the rotor system, constrained layer damping (CLD) treatment is applied to the composite flexures. Modal analysis of composite flexures with attached viscoelastic and constraining layers are performed using MSC/NASTRAN, and the effectiveness of CLD treatments are validated through modal test. The composite flexures with CLD are applied to a hingeless rotor system. The rotor system is tested in hovering condition and it is shown that in-plane damping is increased by means of CLD treatments.

• Journal of Power System Engineering
• /
• v.1 no.1
• /
• pp.124-143
• /
• 1997

본 논문은 능동 구속층 감쇠(active constrained layer damping) 처리된 관의 동적 모델링과 정식화를 제시한다. 판의 운동방정식은 Hamilton정리를 이용하여 전개된 판, piezoelectric film 및 점탄성층의 운동방정식을 조합하므로서 유도된다. 이 운동방정식은 외부인가전압의 영향하에서 적층판의 해석적 모델을 제공할 뿐만이 아니라, 판 구조내에서 진동에너지를 감소시킬 수 있는 전단층의 효과에 대한 변위관계식을 나타낸다. 그리고 운동방정식에 대응하는 경계조건도 유도되었다. 또한 판과 능동구속층감쇠계의 동특성을 설명하기 위한 유한요소모델이 유도되었다. 이 모델의 타당성을 실온조건에서 실험적으로 입증하였다. 개발된 이론 및 실험적인 결과들은 판과 능동구속층 감쇠계가 구조진동의 감쇠를 위한 매우 유효한 수단으로 사용될 수 있음을 나타내었다.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.1
• /
• pp.90-98
• /
• 1999

For the control of vibration and noise of metal structures having relatively low damping, viscoelastic materials are widely used and usually attached at metal structures with an additional constraining layer to secure them. The damping and elastic properties of structures having constrained viscoelastic material layers are dependent on not only temperature and frequency but also their thicknesses. Hence, optimal design of the thicknesses of viscoelastic and constraining layers for a certain base structure are very important to maximize their efficiency and to lighten their weight. In this study, the variation of loss factor of beams having a constrained viscoelastic layer according to the change of thickness has been carefully investigated. From these, optimal design method of the minimum thickness beam having a given loss factor is suggested and numerically verified for a real beam.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.5
• /
• pp.115-128
• /
• 2001

본 논문에서는 반복하중이나 지진하중을 받는 지반-구조물 시스템의 설계에 필수적인 변수인 전단탄성계수와 감쇠비에 대한 연구를 국내에 존재하는 비점성토 지반에 대하여 수행하였다. 국내 퇴적토지반 및 풍화토지반에서 채취된 자연시료와 입도분포를 조정하여 제작한 시료를 포함하여 총 60개의 시료에 대하여 20kPa에서 500kPa의 구속응력 범위에서 공진주 시험을 수행하고, 이를 조립질 사질토, 실트 및 실트질 모래, 풍화토의 3개의 그룹으로 나누어 결과를 정리하였다. 저변형률 영역의 변형특성인 최대전단탄성계수와 최소감쇠비에 대하여 구속응력의 영향을 확인하였다. 최대전단탄성계수를 예측하는 경험식을 3개의 그룹별로 제안하였다. 최소감쇠비는 구속응력에 따른 분포영역을 제시하였다. 세립분이 적은 조립질 사질토의 경우, 비선형 변형특성이 구속응력의 영향을 뚜렷이 받고 있어 이를 주요한 변수로 고려하여 대표곡선과 분포영역을 제안하였다. 구속응력의 영향을 적게 받는 실트 및 실트질 모래와 풍화토는 구속응력에 관계없이 대표곡선과 분포영역을 제안하였다. 제안된 각 시료의 대표곡선과 기존의 Vucetic-Dobry와 Seed-Idriss가 제안한 곡선과 비교하였다. 본 논문의 연구결과는 국내지반의 비점성토 지반에 대한 지진해석이나 동하중을 받는 시스템의 해석시 유용하게 사용될 것으로 판단된다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.3
• /
• pp.45-55
• /
• 2001

The purpose of this paper is to present the optimal design method of viscoelastic dampers and support brace stiffnesses. The dynamics of visco-elastic dampers and support braces connected in series is modeled by state equation. A constraint on maximum story drifts which are computed using RMS\`s of story drifts and peak factors is added to the optimization problem. The number of variables is reduced by including the constraint associated with the dynamic behavior of the structure in the procedure to compute the gradient of the inequality equation about constraint on the maximum story drifts. In the design example, it is confirmed that the design of dampers considering support brace stiffnesses is necessary when sufficient brace stiffnesses cannot be supplied. It is also found that unnecessary brace stiffnesses can be removed by adding brace stiffnesses to optimal design variables and that the increase of damper volumes to compensate for the variation of maximum story drifts is pretty small.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.5
• /
• pp.429-437
• /
• 2009

This study addresses the optimal shape of a LCVA maximizing its vibration control effect through numerical parametric study. Various LCVAs having the same total mass and tuning frequency are designed with constraints on the dimensions and water level, and one obtaining the highest equivalent damping ratio of the controlled system is chosen as an optimal solution. As a result, it was found that the limit on the variation of the water level in the vertical liquid column plays an important role constraining the shape of the LCVA. As the LCVA width perpendicular to the plane of liquid motion increases, the equivalent damping ratio rises with slowdown so that determination of the proper width is important in design of the LCVA shape.

• Geotechnical Engineering
• /
• v.3 no.2
• /
• pp.7-16
• /
• 1987

The dynamic properties of soils are affected by parameters like, gradation characteristics, void ratio, confining pressure, etc. . This study mainly investigated experimentally the effect of gradation on the dynamic properties of sands with the effect of void ratio and confining pressure. Test results showed that shear modulus/damping ratio was increased/decreased with the decrease of void ratio and with the increase of confining pressure. When the fine content increased, shear modulus/damping ratio was decreased/increased. This study explained this phenomenon by the concept of the "effective number of contacts" and the "dead space".ot;dead space".uot;.

• Geotechnical Engineering
• /
• v.2 no.1
• /
• pp.55-66
• /
• 1986

Considering the effects of confining pressure, initial shear stress, cyclic stress ratio and number of loading cycles, cyclic triaxial tests are carried out to clarify the soil dynamic properties such as shear modulus and value of material damping of clay under undrained cyclic loading conditions. The results show that no obvious dependency on initial shear stress and effective confining stress are recognized in the shear modulus and damping ratio plotted versus strain. However, the shear modulus decreases and the damping ratio increases with increasing axial strain. When compared with others, it is also revealed that the shear moduli are distributed within the range curves obtained using empirical equations derived by Marcuson et al. (3) and Kokusho et al. (4), and damping ratios are distributed between the curves obtained by Kokusho et al. (4) and Ishihara et al. (9).

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.04a
• /
• pp.239.2-243
• /
• 1999

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.2
• /
• pp.31-38
• /
• 2008

A column test was performed far a new-type column with a quasi static test. An internally confined hollow reinforced concrete column with a corrugated steel tube (ICH RC-CT column) was tested to evaluate its seismic performance. And also, a general solid RC column was tested fur the comparison. The test was performed as planned drift levels. The lateral displacements and the lateral loads of column specimens were measured during tests. From the test results, the ICH RC-CT column showed smaller energy absorbing capacity than a solid RC column but showed the almost equal energy ductility and equivalent viscous damping ratio to those of the solid RC column.