• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.363-368
• /
• 2006

This study selected the optimal catalyst for the process of producing $C_9$-alcohol by hydrogenating $C_9$-aldehyde, and carried out an experiment in order to establish the operating condition for maximizing the yield of $C_9$-alcohol. The BET surface area and the specific area of copper were most excellent in $CuO/ZnO/Al_2O_3$ (60:30:10 wt％) catalyst produced using acetate as a precursor of copper and $Na_2CO_3$ as a precipitant, and the catalyst also showed the highest performance in $C_9$-aldehyde hydrogenation. Using a trickle bed reactor loaded with optimized catalyst, we attained 94.1 wt％ yield of $C_9$-alcohol under the condition of $175^{\circ}C$, 800 psi and $WHSV=3hr^{-1}$. According to the result of comparing with other catalysts used in the hydrogenation of aldehyde, the catalyst showed similar performance to that of Ni/kieselghur and higher than that of $Cu-Ni-Cr-Na/Al_2O_3$ and $Ni-Mo/Al_2O_3$. According to the result of examining the stability of the catalyst through a long-term catalysis test, the yield of $C_9$-alcohol decreased slowly after around 72 hours due to the increasing production of high boiling-point byproducts.

• Clean Technology
• /
• v.27 no.1
• /
• pp.9-16
• /
• 2021

Since the active matrix organic light-emitting diode (AMOLED) encapsulation process is very vulnerable to moisture and oxygen, high-purity nitrogen with minimal moisture and oxygen must be used. In this study, a copper-based catalyst used to remove oxygen from nitrogen in the AMOLED encapsulation process was optimized. Two-component and three-component catalysts composed of CuO, Al2O3, or ZnO were prepared through a co-precipitation method. The prepared catalysts were characterized by using BET, XRD, TPR, and XRF analysis. In order to verify the oxygen removal performance of the catalyst, several catalytic reactions were conducted in a fixed bed reactor, and the corresponding oxygen contents were measured through an oxygen analyzer. In addition, reusability of the catalysts was proven through repetitive regeneration. The properties and oxygen removal capacity of the catalysts prepared with CuO and Al2O3 ratios of 6 : 4, 7 : 3, and 8 : 2 were compared. The number of active sites of the catalyst with a ratio of CuO and Al2O3 of 8 : 2 was the highest among the 2-component catalysts. Moreover, the reducibility of the catalyst with a ratio of CuO and Al2O3 of 8 : 2 was the best as it had the highest CuO dispersion. As a result, the oxygen removal ability of the catalyst with a ratio of CuO and Al2O3 of 8 : 2 was the best among the 2-component catalysts. The best oxygen removal capacity was obtained when 2wt% of ZnO was added to the sub-optimized catalyst (i.e., CuO : Al2O3 = 8 : 2) probably due to its outstanding reducibility. Furthermore, the optimized catalyst kept its performance during a couple of regeneration tests.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.302-310
• /
• 2001

Cu/PET film composites were prepared by electroless copper plating method. In order to improve adhesion between electroless Cu plated layer and polyester (PET) film, the effect of pretreatment conditions such as etching method and mixed catalyst composition, and accelerator was investigated. Compared to NaOH etching medium, PET film was more finely etched by HCl solution, resulting in an improvement in adhesion between Cu layer and PET film. However, there were no significant differences in electromagnetic interference shielding effectiveness as a function of etching medium. The surface morphology of Cu plated PET film revealed that Pd/Sn colloidal particles became more evenly distributed in the smaller size by increasing the molar ratio of PdCl$_2$ : SnCl$_2$ from 1 : 4 to 1 : 16. With increasing the molar ratio of mixed catalyst, the adhesion and the shielding effectiveness of Cu plated PET film were increased. Furthermore, HCl was turned out to be a better accelerator than NaOH in order to enhance the activity of the mixed PdCl$_2$/SnCl$_2$ catalyst, which facilitated the formation of more uniform copper deposit on the PET film.

• Journal of Energy Engineering
• /
• v.6 no.1
• /
• pp.26-33
• /
• 1997

Highly crystalline Cu-ZSM5 was prepared without using organic templates. Several ion exchange treatments between Na$\^$＋/ and Cu$\^$2＋/ brought about excess loading of copper ions on the ZSM5 zeolite and the resultant zeolite was active for the decomposition of NO. This indicates that the copper ions excessively loaded on the ZSM5 zeolite are effective for the NO decomposition. When oxygen was added to a reactants, the conversion of NO decreased. NO, O$_2$TPD experiments explained that the active sites for NO decomposition and the adsorption sites of O$_2$, were the same. O$_2$, at the surface of ZSM5 zeolite was desorbed incompletely after pretreatment at 500$^{\circ}C$, and CU-ZSM5 pretreated with H$_2$at 500$^{\circ}C$ showed promoted activity at the start of reaction. Thus, it seems clear that O$_2$, adsorbed ai the surface of catalyst inhibits the catalytic activity.

• Journal of the Korean Institute of Gas
• /
• v.26 no.5
• /
• pp.16-21
• /
• 2022

The reaction rate of a catalyst for producing hydrogen using the methanol steam reforming reaction was studied. It was prepared by impregnating copper, which is often used in methanol synthesis, as the main active metal, using hydrotalcite, which has excellent porosity and thermal stability, high specific surface area, weak Lewis acid point, and basicity, as a support. Activation energy and Pre-exponential factors were identified. In this study, the activation energy of the hydrotalcite catalyst impregnated with 20 wt% copper was calculated to be 97.4 kJ/mol and the Pre-exponential was 5.904 × 10¹⁰. Process simulation was performed using the calculated values and showed a similar tendency to the experimental results.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2002.05a
• /
• pp.57-60
• /
• 2002

국내에서 사용되고 있는 대부분의 화재대피용 방독마스크 정화통은 외국에서 고가에 수입되고 있거나, 국내 제조시는 많은 기술을 외국에 의존하고 있다. 이들 정화통의 충진재는 일산화탄소(CO)를 제거하기 위해 망간(Mn), 구리(Cu)등을 활성탄에 담지시켜 제조한 촉매층과 $SO_2$, HCI 등의 유독가스를 제거하기 위한 제올라이트 등의 흡착층으로 구성되어있다. 그러나 이들 충진재중 CO 제거용 촉매는 상온에서 CO의 제거효율이 낮아 많은 양을 충진해야 하는 어려움이 있다.(중략)

• Clean Technology
• /
• v.20 no.3
• /
• pp.256-262
• /
• 2014

Catalytic oxidation characteristics of benzene as a VOC was investigated in a fixed bed flow reactor using $Cu/{\gamma}-Al_2O_3$ catalyst. The parametric tests were conducted at the reaction temperature range of $200{\sim}500^{\circ}C$, benzene concentration of 400~650 ppm, gas flow rate of 50~100 cc/min, and space velocity range of $7,500{\sim}22,500hr^{-1}$. The property analyses by using the BET, SEM, TGA and the conversion of catalytic oxidation of benzene were examined. The experimental results showed that the conversion was increased with decreasing benzene concentration, gas flow rate and space velocity. Benzene oxidation reaction over $Cu/{\gamma}-Al_2O_3$ catalyst could be expressed as the first order homogeneous reaction of which the activation energy was 17.2 kcal/mol and frequency factor was $1.33{\times}10^6sec^{-1}$.

• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.863-867
• /
• 2008

Pitch based activated carbon fiber(ACF) was prepared from reformed naphtha cracking bottom oil(NCB oil) by melt spinning. The fibers obtained were stabilized, carbonized, and then steam activated. The ACF was sensitized with Pd-Sn catalytic nuclei via a single-step activation approach. This sensitized ACF was used as precursors for obtaining copper plated ACFs via electroless plating. ACFs uniformly decorated with metal particles were obtained with reduced copper plating in the reaction solution. Effects of the amount of copper on characteristics of ACF/Cu catalysts were investigated through BET surface area, X-ray diffraction, scanning emission microscopy, and ICP. The amount of copper increased with plating time, but the surface area as well as the pore volume decreased. NO conversion increased with reaction temperature. NO conversion decreased with increasing the amount of copper, which is seemed to be due to the reduction of surface area as well as the dispersion of copper.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.474-481
• /
• 2018

The policy-making and technological development of eco-friendly automobiles designed to increase their supply is ongoing, but the internal combustion engine still accounts for approximately 95% of automobiles in use. To meet the stricter emission regulations of internal combustion engines based on fossil fuels, the proportion of after-treatments for vehicles and (ocean going) vessels is increasing continuously. As diesel engines have high power and good fuel economy in addition to less CO2 emissions, their market share is increasing not only in commercial vehicles, but also in passenger cars. Because of the characteristics of the diesel combustion, however, NOx is generated in localized high-temperature combustion regions, and particulates are formed in the zones of diffusion combustion. LNT and urea-SCR catalysts have been developed for the after-treatment of exhaust gas to reduce NOx in diesel vehicles. This study examined the effect of a containing promoter on SCR catalysts to cope with the severe exhaust gas regulation. The de-NOx performance of the Mn-SCR catalyst was the best, and the de-NOx performance was improved as the ion exchange rate between Mn ion and Zeolyst was good and the activation energy was low. The de-NOx performance of the 7Cu-15Ba/78Zeoyst catalyst was 32% at $200^{\circ}C$ and 30% at $500^{\circ}C$, and showed the highest performance. The NOx storage material of BaO loaded as a promoter was well dispersed in the Cu-SCR catalyst and the additional de-NOx performance of BaO was affected by the reduction reaction of the Cu-SCR catalyst. Among the three catalysts, the 7Cu-15Ba/Zeolyst SCR catalyst was resistant to thermal degradation. The same type of CuO due to thermal degradation migrates and agglomerates because BaO reduces the agglomeration of the main catalyst CuO particles.

• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.423-427
• /
• 2010

Carbon nano sphere(CNS) and nano bowl of carbon(NBC) containing 1.0 wt% copper were prepared by impregnation method and their catalytic activity was compared in the phenol hydroxylation with hydrogen peroxide in the presence of water and acetonitrile as a solvent, respectively. Cu content of catalysts was determined by EDS, and BET, pore volume, pore size and pore size distribution were compared. For both catalysts, phenol conversion, $H_2O_2$ efficiency and yield of catechol and hydroquinone were higher in the presence of water as a solvent than those in the presence of actonitrile. And catalytic activity such as phenol conversion and $H_2O_2$ efficiency of 1.0 Cu/CNS is about two times higher than that of 1.0 Cu/NBC in water solvent.