• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.235-242
• /
• 2014

To investigate pressure distributions on the shaft surface of the air bearing, the commercial CFD software was employed to study three different nozzle geometries to improve the nozzle performance: general drill-shaped, matched cube-shaped and trimmed exit nozzles. Under the influence of stagnation point, the maximum pressure was observed at the center of shaft surface for all cases. Owing to the blocking effect of a fine gap between the shaft surface and the nozzle exit, the drill-shaped nozzle has the rapid local pressure increase near the nozzle exit corner, generating the ring vortex in the radial direction within pressure ratio of 6.92, and its pressure becomes negative in a certain range of downstream. In comparison, the contoured nozzle showed a local pressure increase in the measured range of pressure ratios, but a negative pressure appeared within the pressure ratio of about 10. The trimmed nozzle was seemed to extend the high pressure zone near the stagnation point in the radial direction substantially, and no negative pressure was appeared in the whole range. Based on these observations, it is found that trimming nozzle exit becomes more effective for improving the performance than modifying the nozzle inside contour.

• The Journal of Engineering Geology
• /
• v.22 no.2
• /
• pp.145-155
• /
• 2012

The matric suction and volumetric water content of Jumunin standard sand with a relative density of 60% were measured using an Automated Soil-Water Characteristic Curve (SWCC) apparatus during both drying and wetting processes. The test time for the drying process was longer than that for the wetting process, because the flow of water is likely to be protected by air trapped in voids within the soils during the drying process. Based on the matric suction and volumetric water content, the SWCC was estimated using the model proposed by van Genuchten (1980). For the drying process, the unsaturated fitting parameters ${\alpha}$, n, and m were 0.399, 8.586, and 0.884, respectively; for the wetting process, the values were 0.548, 5.625, and 8.220, respectively. The hysteresis phenomenon occurred in the SWCCs, which means the SWCC of the drying process is not matched with the SWCC of the wetting process. Using these unsaturated parameters, we estimated the Suction Stress Characteristic Curve (SSCC), based on the relationship between suction stress and the effective degree of saturation. The suction stress showed a rapid decrease when the matric suction exceeds the Air Entry Value (AEV). Therefore, the effective stress of unsaturated soils is different from that of saturated soils when the matric suction exceeds the AEV. The suction stress of the drying process exceeds that of the wetting process for a given effective degree of saturation. The hysteresis phenomenon was also recognized in SSCCs. The hysteresis phenomenon of SSCCs arises from that of SWCCs, which is induced by the ink bottle effect and the contact angle effect. In the case of a sandy slope, the suction stress is positive and acts to enhance the slope stability as the water infiltrates the ground, but is negative when the suction stress exceeds the AEV. The results obtained for the wetting process should be applied in analyses of slope stability, because the process of water infiltration into ground is similar to the wetting process.

• Journal of Sensor Science and Technology
• /
• v.9 no.2
• /
• pp.96-105
• /
• 2000

Fiber optic TR-EFPI(total reflected extrtinsic Fabry-Perot interferometric) sensor was developed to measure the strain of structures, such as building, bridge, aircraft, etc. It has been difficult to distinguish the increase and decrease of the strain from the conventional fiber optic EFPI sensor because their signals only have a sinusoidal wave pattern related to the change of strain. Also, the absolute strain could not be measured by the simple fiber optic EFPI sensor. In this study, in order to measure the magnitude of strain with the direction of strain, the fiber optic sensor was simply constructed with the total reflected EFPI sensor probe. This probe was manufactured with a single mode fiber and a mirror coated fiber in a silica glass capillary tube. The output signal of this fiber optic TR-EFPT sensor can give the information about the magnitude and the direction of strain. The loading-unloading test was performed by the universal testing machine with alluminum beam specimen to compare the strain from fiber optic TR-EFPI sensor with the value from electrical strain gauge. In the result of this experiment. the strain from fiber optic TR-EFPI sensor had a good agreement with the values from the electrical strain gauge.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.5
• /
• pp.5-14
• /
• 2007

The quantity of noxious wastes generated by the growth in industrialization and population in all over the world and its potential hazards in subsurface environments are becoming increasingly significant. The extraction of the contaminant from the soil and movement of the water are restricted due to the low permeability and adsorption characteristics of the reclaimed soils. Incorporated technique with PVDs have been used for dewatering from fine-grained soils for the purpose of ground improvement by means of soil flushing and soil vapor extraction systems. This paper is to evaluate several key parameters that affected to the performance of the PVDs specifically with regard to: well resistance of PVD, zone of influence, and smear effects. In the feasibility of contaminant remediation was evaluated in pilot-scale laboratory experiments. Well resistance is affected on the vertical discharge capacity of the PVDs under the various vacuum pressures. The discharge capacity increases consistently in areal extents with higher applied vacuum up to a limiting vacuum pressure. The head values for each piezometer at different vacuum pressures show that the largest head loss occurs within 14 cm of the PVD. Air flow rates and head losses were measured for the PVD placed in the model test box and the gas permeability of the silty soils was calculated. Increasing the equivalent diameter results in a decrease in the calculated gas permeability. It is concluded that the gas permeability determined over the 1,500 to 2,000 $cm^3/s$ flow rates are the most accurate values which yields gas permeability of about 3.152 Darcy.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.2
• /
• pp.47-56
• /
• 2013

There are many technical problems, which can not be resolved by the concept of saturated soil mechanics. Unsaturated soils show an apparent cohesion due to negative pore pressure and relatively lower permeability due to entrapped air compared to saturated soils. The determination of engineering properties of soils with various moisture content is very important to evaluate shear strength and stability of natural and engineered soils. So various researches should be made on unsaturated soils. Especially, sandy soils are widely distributed near Nakdong river, one of the four rivers where Restoration Projects were carried out. Many structures such as dams, flood control facilities, detention facilities and reservoirs have been built in this area. In this study, unsaturated triaxial compressive tests were conducted on sands or silty sands at Nakdong river in order to provide their fundamental characteristics for design and construction of geotechnical structures. As a result of the tests, the maximum deviator stress increased as the confining stress and matric suction increased. The cohesion increased non-linearly as the matric suction increased, but the angle of internal friction was marginally changed.

• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.329-335
• /
• 2001

Recently, in many laboratories and institutes it is being studied on the high flowing concrete widely, which has high fluidity, non-segregation ability and fillingability, and sometimes being applied to the construction field actually. And the fluidity properties of high flowing concrete are influenced according to the several factors ; binder content, water/binder ratio and water content etc. This is an experimental study to compare and analyze the effect of water/binder ratio and water content on the properties of high flowing concrete. For this purpose, the mix proportion of high flowing concrete according to water/binder ratio(W/B : 0.30, 0.35, 0.40, 0.45) and water content (W : 155, 165, 175, 185 kg/㎥) was selected. And then slump-flow, V-lot, L-passing test in fresh concrete, and compressive strength, freezing and thawing test in hardened concrete were peformed. According to test results, it was found that the viscosity of all those high flowing concrete with the water content 175 kg/㎥ was satisfied with 50 cm pass time of slump flow prescribed by Japanese Architectural Standard Specification (JASS 5) - from 3 to 8 seconds. And non-segregation ability of concrete with W/B 0.35 was better than the other mix proportions. Especially, the compressive strength after curing 24 hours(1 day) of all high flowing concrete was higher than that prescribed by JASS 5(50 kgf/㎠).

• Korean Journal of Ichthyology
• /
• v.4 no.2
• /
• pp.1-25
• /
• 1992

Taxonomic study of the five species (Acanthogobius elongata, A. flavimanus, A. lactipes, A. luridus and Synechogobius) from Korea was carried out based on morphometric, cephalic sensory canal and ecological characters. Taxonomic revision and classificational keys are provided. Synechogobius hasta is easily distinguished from four species of the genus Acanthogobius in eleven characters, i. e., the number of dorsal and anal fin rays, the transverse scales, the vertebral numbers, the formula of interneural spine of the first dorsal fin, the number of interhemal spine anterior to the first hemal spine, the number of epipleural and pleurals, the ratio of caudal peduncle length, the ratio of caudal peduncle depth and the regular variations in the ratio of body parts with the body length. In the genus Acanthobobius, A. elongata is distinguished from other 3 congeneric species in the ratio of body parts and the oculoscapular sensory canal. Moreover, A. flavimanus differs from other 3 congeneric species in the lateral scales, the transverse scales, the number of predorsal scales, the vertebral number, the number of epipleural and pleurals. Sensory papillae rows of S. hasta is not similar that of the genus Acanthogobius in having a singular sensroy papillae rows. A. elongata has no oculoscapular sensory canal D and A. flavimanus has transverse sensory papillae in cheek, and these are one of the unique characters distinguished form other congeneric species. In the spawning period inferred from gonadosomatic index, A. elongata varied from late March to late June ; A. flavimanus, January to April ; A. lactipes, May to September ; A. luridus, early May to early July and S. hasta, early March to early May.

• The Bulletin of The Korean Astronomical Society
• /
• v.46 no.2
• /
• pp.73.4-74
• /
• 2021

한국천문연구원은 2017년 제1차 구술채록사업에 이어 2020년 제2차 사업을 진행하면서 최초로 원외 원로에 대한 구술채록을 시도하였다. 국가 대표 천문연구의 산실로서 연구원 존재 의의를 확립하기 위하여 원내 원로에 국한되었던 구술자 대상을 확장한 것이다. 그 첫 외부 구술 대상자로 방득룡 전임 노스웨스턴 천문학과 교수를 선정하여 2020년 7월부터 준비단계에 들어갔다. 방득룡 전(前)교수가 첫 번째 한국천문연구원 원외 인사 구술자로 선정된 이유는, 그가 우리나라 천문대1호 망원경 구매 선정에 개입한 서신(1972년)이 자료로 남아있었기 때문이다. 한국천문연구원에서 2017년에 수행한 제1차 구술채록사업에서 구술자로 참여한 오병렬 한국천문연구원 원로가 기증한 사료들은 대부분 연구원 태동기 국립천문대 구축과 망원경 구매 관련 자료였으며 이 가운데 1972년 당시 과학기술처 김선길 진흥국장에게 Boller and Chivesns(사(社))의 반사경을 추천한 방득룡 전(前)교수의 서신은 한국 천문학 발전사에서 중요한 사료였다. 연구진은 이 자료를 시작으로, 방득룡 전(前)교수의 생존 여부와 문서고의 공기록물들에서 그의 흔적을 찾아가기 시작했다. 놀랍게도 그는 실제 세계와 한국천문연구원 문서고 깊숙이 기록물들 모두에서 상존하고 있었다. 1927년생인 방득룡 전(前)교수, Dr. John D. R.은 미국 플로리다 한 실버타운에서 건강한 정신으로 생존하여 있었고 연구진의 인터뷰에 흔쾌히 응했다. 2020년 9월 16일에 한국천문연구원 본원 세종홀 2층 회의실에서 영상통신회의로 그와의 구술인터뷰가 진행되었다. 이 구술인터뷰는 원외 인사가 대상이란 점 외에도 방법적으로는 전형적인 대면 방식이 아닌 영상 인터뷰였다는 점에서 코로나 시대의 대안이 되는 실험적 시도였다. 현대 한국천문학 발전사의 재조명 측면에서도 의미가 있었다. 1960년대 초반부터 1992년 정년퇴임까지 30년을 미국 유수 대학교 천문학과 교수로 재직하며 활발한 활동을 해 온 한국계 천문학자가 우리나라 최초 반사망원경 구매 선정에 적극 개입하였던 역사는, 공문서 자료들과 서신 사료들에 이어 그의 육성으로 나머지 의구심의 간극이 채워졌다. 또 구술자 개인이 주관적으로 중요하다고 여기는 '기억'이 중요한 아카이빙 콘텐츠 확장의 단초가 될 수 있다는 것을 보여줌으로써 구술사 연구에 있어서도 중요한 관점을 주었다. 애초 연구진이 방득룡 전(前)교수의 공식 기록에서 아카이빙의 큰 줄기로 잡았던 것은 1948년 도미, 1957년 위스콘신 대학교 천문학 박사학위 취득, 1962년부터 노스웨스턴 대학(일리노이주 에반스턴)의 천문학 교수진, 1992년 은퇴로 이어진 생애였다. 그러나 그와의 구술 준비 서신 왕래와 구술을 통하여 알게 된 그가 인생에서 중요시 여겼던 지점은, 1948년 도미 무렵 한국의 전쟁 전 상황과 당시 비슷한 시기에 유학한 한국 천문학자들의 동태, 그리고 1957년부터 1962년까지 프린스턴 대학교에서 M. Schwarzschild 교수와 L. Spitzer 교수를 보조하며 Stratoscope Project를 연구하였던 경험이었다. 기록학적 의미에서도, 전자를 통해서 그와 함께 동시대 한국 천문학을 이끌었던 인재들의 맥락정보를 얻을 수 있었으며, 후자를 통해서는 세계 천문학사에 큰 영향을 미친 석학에 대한 아카이브 정보와의 연계 지점과 방득룡 전(前)교수의 연구 근원을 찾을 수 있었다. 이들은 추후 방득룡 콘텐츠 서비스 시에 AIP, NASM, Lyman Spitzer 콘텐츠, 평양천문대, 화천조경천문대, 서울대와 연세대, 그리고 한국천문연구원까지 연계되어 전 세계 폭넓은 이용자들의 유입을 유도할 수 있는 검색 도구가 될 수 있다. 이번 방득룡 구술사 연구에서 구술자 개인의 주관적인 소회가 공식 기록이 다가갈 수 없는 역사적 실체에 일정 부분 가까울 수 있다는 것, 그리고 이를 통하여 개인의 역사는 공동체의 역사로 확장될 수 있다는 사실을 발견할 수 있었다. 또 연구진은 방득룡 전(前)교수의 회상을 통하여 구술자 개인의 시각으로 한국과 미국 천문학계의 공동체 역사를 재조명할 수 있었고, 이것을 아카이브 콘텐츠 확장 서비스에 반영할 수 있다는 기대를 가지게 되었다. 무엇보다 이 연구를 통하여 다양한 주제의 아카이브로 연동될 수 있는 주제어와 검색도구를 구술자 개인의 회상으로부터 유효하게 도출할 수 있다는 것을 확인하였다. 그리고 향후 한국천문 구술아카이브의 확장을 통하여 보다 다양한 활용과 연구 재활용의 선순환이 가능하다는 것도 알 수 있었다. 이는 최근 기록학계에서 대두되고 있는 LOD(Linked Open Data)의 방향성과도 흡사하여 한국천문학 구술사연구의 차세대 통합형 기록관리의 미래모형을 기대케 하는 대목이다.