• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.105-111
• /
• 1993

내연기관의 혼합 가스 생성 장치로 흡입되는 공기의 유량을 조절하기 위해 Butterfly 밸브가 사용 된다. 이 밸브는 유량의 제어에는 매우 유용한 반면, 밸브 후면에서의 복잡한 공기의 유동현상[6] 으로 인하여 혼합가스의 생성에 장해적인 요소를 제공하기도 한다. 특히 밸브가 많이 닫힌 상태 에서는 밸브와 관로벽 사이의 간격이 좁아지는 Throttling 현상으로 인하여, 엔진에 고 부하시 흡 입되는 공기의 양이 증가하게 되어, 밸브 주위에서 공기 속도의 급증으로 인하여 유동장의 압축 성 현상을 기대할 수 있다. Throttle의 Choking 현상으로 인하여 공기의 입자는 운동에너지를 잃 게 되고, 궁극적 혼합가스의 생성에 영향을 미쳐 엔진성능의 저하를 초래하게 된다. 본 연구에서 는 실제 엔진(Central Fuel Injection Engine, 5 liters) [1]의 흡인 manifold를 modelling하여, 특히 밸브가 많이 닫힌 상태에서, 밸브 주위에서의 난류 유동의 압축성 현상을 정량적으로 분석해 보았다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.9
• /
• pp.76-81
• /
• 2006

This paper deals with a fuel metering unit (referred to as FMU) for air breathing engine. The proposed FMU consists of a constant pressure drop valve and a metering valve, both of which are controlled by servovalve. Linear analysis derived from a nonlinear mathematical model of FMU is carried out to find major parameters on the system performance. Numerical results using established model of FMU were in good agreement with the experimental results. It is also shown that the system stability is improved by reducing the constant pressure drop at metering valve and applying the triangular orifice to constant-pressure-drop valve through the simulation and experiments.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1698-1703
• /
• 2004

To understand the high expansion effects by adopting intake closing time in the cases of compensating intake air-mass and effective compression ratio simultaneously, fundamental study was carried out by using RICEM realizing Atkinson cycle. Intake air-mass and effective compression ratio were compensated by increasing supercharged pressure and geometric compression ratio. The results showed that the increasing rates of expansion ratio and expansion-compression ratio were increased by compensating both a intake air-mass and effective compression ratio the same tendencies were obtained with the increases of compression ratio and cut off ratio It was also found that LIVC has more advantages in expansion ratio and effective work than those of EIVC under above conditions.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.2
• /
• pp.86-94
• /
• 1987

In order to examine the flow motion in a combustion chamber of a motored diesel engine, the variation of instantaneous are velocity at a fixed point in combustion chamber was measured by the constant temperature hot wire anemometer, varing engine speed, shroud shape and shroud position. The results are summerized as follows: 1. The variation of air velocity in a combustion chamber is closely related with the valve timing and piston velocity. 2. The air velocity in the cylinder at suction stroke is being increased and maximized at 60$^{\circ}$ ABDC in compression stroke and then decreased at the e.v.o. in expansion stroke. 3. The mean velocity using shroud valve was less than no shroud valve. However the turbulent intensity using shroud valve was larger than no shroud valve. 4. The turbulent intensity with 90$^{\circ}$shroud valve was larger than that of 120$^{\circ}$shroud valve, and 90$^{\circ}$shroud valve at 180$^{\circ}$shroud position had the largest turbulent intensity.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.2
• /
• pp.40-40
• /
• 1987

In order to examine the flow motion in a combustion chamber of a motored diesel engine, the variation of instantaneous are velocity at a fixed point in combustion chamber was measured by the constant temperature hot wire anemometer, varing engine speed, shroud shape and shroud position. The results are summerized as follows: 1. The variation of air velocity in a combustion chamber is closely related with the valve timing and piston velocity. 2. The air velocity in the cylinder at suction stroke is being increased and maximized at 60° ABDC in compression stroke and then decreased at the e.v.o. in expansion stroke. 3. The mean velocity using shroud valve was less than no shroud valve. However the turbulent intensity using shroud valve was larger than no shroud valve. 4. The turbulent intensity with 90°shroud valve was larger than that of 120°shroud valve, and 90°shroud valve at 180°shroud position had the largest turbulent intensity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.8
• /
• pp.1009-1015
• /
• 2011

In this study, in the high expansion cycle was conduced by variable valve timing system composition to close intake valve late, and in the intake air reduction on the low compression was solved by supercharging pressure. In this wise, by constituting Diesel-Atkinson cycle, this study looked into a possibility of thermal efficiency improvement. As a result, there was improvement in thermal efficiency and output in a whole range of closing timing from ABDC $40^{\circ}$ to ABDC $80^{\circ}$. However, after ABDC $70^{\circ}$ of closing timing, the thermal efficiency increase was getting smaller. As the result of the study, the optimum intake valve closing timing was about ABDC $70^{\circ}$, high loading territory of engine was more effective than low loading territory, and engine operation in middle loading territory was stable. At this time, brake thermal efficiency was 12.5% higher than ordinary engine on average.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.668-670
• /
• 2012

본 논문에서는 시작엔진 제작에 앞서 CFD기법을 이용하여 디젤 엔진 흡기포트의 유동 특성을 분석하고자 하였다. 유동 해석 결과 높은 밸브리프트에서는 흡기포트 곡률 최적화로 인해 흡입 공기량이 극대화되었으며, 낮은 밸브리프트에서는 스월 Chamfer를 적용하여 스월유동이 강화된 것을 확인할 수 있었다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.82-88
• /
• 1999

The object of this study is to find new evaluation index for in-cylinder flow chracteristics istead of current swirl, tumble coefficient using steady flow test rig on intake port system. To this end, port flow system. To this end, port flow rig test was conducted on DOHC head varying intake valve lift respectively. Finally combination angular coefficient and inclination angle were introduced as new evaluation index for in-cylinder angularflow characteristics instead of swirl and tumble coefficient.

• Journal of Power System Engineering
• /
• v.11 no.4
• /
• pp.5-11
• /
• 2007

본 연구는 SI기관 실린더 내의 유동장 변이 과정을 3차원 LDV 측정 기술을 사용하여 흡입과 압축과정 동안 정량적으로 분석하였다. 실험은 헤드에 각각 2개의 흡입밸브와 배기밸브를 갖는 기관이 모터링되는 공회전 상태에서 실시하였다. 지난 30년 동안 텀블과 스월은 실린더 내의 평균 유동 정량화에, 난류운동에너지는 난류 측정에 많이 사용되어 왔다. 그러나 텀블은 solid body 회전 유동을 비교하는데 적절하며, 서로 다른 유동 패턴 비교에는 부적절 하다는 것이 보고되고 있는 실정이다. 3차원 LDV시스템의 우수한 공간 분석 능력은 순간적인 유동장구조와 더불어 상대적으로 미세한 유동장의 구조 까지도 측정이 가능 하도록 하였다. 따라서 측정한 결과로부터 유동장의 난류운동에너지 등가면을 계산할 수 있었다. 본 실험 결과는 실린더 내의 난류 유동장 특성을 난류운동 에너지 등가면 정보를 이용하여 세심하게 관찰할 수 있음을 제시하고 있다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1229-1235
• /
• 2014

At the LPG vehicle air intake system, most of dust particles in the air cleaner are removed. However very small particles are not removed and accumulated. The accumulation of carbon in air intake system is going to affect the idle speed control and sensor signal. It also causes engine chattering and transmission troubles of automatic transmission. This is study about cleaning up intake system using cleaning chemical. We can clean up the intake system by spraying cleaning liquid onto intake device when the engine is idling after intake hose is removed from warmed up vehicle. We can obtain the following experimental results by cleaning up ISC, surge tank, intake manifold, intake valves and combustion chamber. According to this results, the stroll valve works correctly and power rate of engine is up to the standard, it is smoothy to control the idling speed when a vehicle pulls up. After cleaning up CO grow down about 0.15%, HC does about 20~100 ppm.