• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.39-40
• /
• 2010

The demands for longer span and reduction of story height have greatly increased as building structures become much larger and higher in recent years. Although the development of flexural members for reducing story height or making long span has been studied by many researchers and engineers, there is still a lack of efficient systems that meet these two demands simultaneously. This study aimed at developing a new composite beam system suitable for long span and reduction of story height, and proposed a prestressed composite beam with corrugated web. It has great resistance against non-symmetric construction load due to its strong out-of-plane shear strength with relatively small member height as well as good constructability and economic efficiency by removing/minimizing form work. The corrugated webs also make accordion effect introducing larger effective prestressing force to top and bottom flanges, which causes larger upward camber reducing the member deflection. Five full-scale specimens with key test parameters, which are web sectional shapes and number of drape points, were tested to understand their flexural behavior and to verify the performance of the proposed method. The experimental test results showed that the proposed prestressed composite beam had greater flexural strength and stiffness than the ordinary non-prestressed composite beam.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.12 no.4
• /
• pp.19-33
• /
• 2008

Dynamic response measurements from natural excitation were carried out for 25- and 42-story buildings to evaluate their inherent properties, such as natural frequencies, mode shapes and damping ratios. Both are reinforced concrete buildings adopting a core wall, or with shear walls as the major lateral force resisting system, but frames are added in the plan or elevation. In particular, shear walls in a 25-story building are converted to frames from the 4th floor level downwards while maintaining a core wall throughout, resulting in a fairly complex structure. Due to this, along with similar stiffness characteristics in the principal directions, significantly coupled and closely spaced modes of motion are expected in this building, making identification rather difficult. By using various state-of-the-art system identification methods, the modal parameters are extracted, and the results are then compared. Three frequency-domain and four time-domain based operational modal identification methods are considered. Overall, all natural frequencies and damping ratios estimated from the different identification methods showed a greater consistency for both buildings, while mode shapes exhibited some degree of discrepancy, varying from method to method. On the other hand, in comparison with analysis results obtained using the initial finite element(FE) models, test results exhibited a significant difference of about doubled frequencies, at least for the three lower modes in both buildings. To improve the correlation between test and analysis, a few manual schemes of FE model updating based on plausible reasons have been applied, and acceptable results are obtained. The advantages and disadvantages of each identification method used are addressed, and some difficulties that might arise from the updating of FE models, including automatic procedures, for such large structures are carefully discussed.

• Journal of the Economic Geographical Society of Korea
• /
• v.1 no.2
• /
• pp.85-102
• /
• 1998

The Changing Characteristics of Office Location in Central Seoul In recent years, central Seoul has been experiencing a dynamic transformation. In the process of reorganization of urban industrial structure including tertiarization and quaternarization of the economic base of Seoul, business services are growing very rapidly and large scale urban renewal projects are agilely implemented. Downtown office activities become a nucleus for economic performance of Seoul and high-rise office buildings steer the landscape transformation of central Seoul. Even though there appear to exist some evidences that office districts have dispersed to several subcenters, major office activities are still concentrated in the central Seoul. This paper redefines office industry in a narrow meaning comprising only relevant economic sectors and office buildings as office activity-functioning units. It then explores the industrial networking and territorial specialization of office activities focusing on the dual process of concentration and dispersion in Seoul. The changing characteristics of the downtown linkages of office activities in this post-industrial era transforms the spatial economy of central Seoul into more flexible and volatile, while territorial concentration of power and control functions are fortified at the same time. Finally, the paper addresses the development of manufacturing-tertiary-quaternary industrial complex, which can be regarded as new industrial clusters, selling cultural economy of urban space and possessing placeness or images for clients and customers, in relation to urban competitiveness and territorial specialization of large metropolitan areas.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.9
• /
• pp.757-765
• /
• 2017

GNSS (Global Navigation Satellite System) Position Accuracy depends on pseudo-range measurement and DOP (Dilution Of Precision) which indicates about navigation satellite geometry. Pseudo-Range has many error sources such as satellite clock, orbit, ionosphere, troposphere, multipath and so on. For the improvement of the accuracy, user can use corrected pseudo-range in DGPS (Differential Global Positioning System), which is one of the relative positioning methods. But, stationary station is needed in relative positioning. In case of DOP, Signal reception environment is important. If receiver sets in the center of city, it could be interrupted reception by buildings. This environment leads to decrease the number of visible satellites and to increase DOP. This paper proposes the concept of GNSS positioning with virtual satellites which have usable VRM (Virtual Range Measurement). Via virtual satellites and VRM, users could get an accurate position. Especially referred virtual satellites constellation has an effect on vertical error.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.5
• /
• pp.73-83
• /
• 2001

The mass and stiffness of upper wall-lower frame system(mixed building structures) change sharply at transfer floor due to different structural system in upper and lower part. These mixed building structures generally show the stiffness, weight or geometric vertical irregularities. The purpose of this study is to investigate the response characteristics of these structures by push-over analysis and nonlinear time history analysis. For four types of analysed models, only the variation of upper wall stories was considered. The conclusions of this study are following; (1) In the push-over analysis, yielding hinges in beams and columns of lower frame occurred at the base shear of similar magnitude in all models. But as the number of stories of upper wall increases, yielding hinges at ends of coupling beams were observed in the small magnitude of base shear. (2) In the nonlinear time history analysis, yielding of lower frame occurred at beams with as small ground acceleration as 55gal, and in upper walls yielding was concentrated on coupling beams and shear walls near the transfer floor. (3) As the number of stories of upper walls decreases, the story stiffness of the lower frames decreased relatively and the occurrence of soft stories in the lower frame was observed.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.11 no.2 s.54
• /
• pp.57-68
• /
• 2007

The mega frame system is becoming popular for the design and construction of skyscrapers because this system exhibits structural efficiency by allowing high rigidity of the structure while minimizing the amount of structural materials to be used. Since the mega frame system is usually adopted for super high-rise buildings, the comfort of occupants may be main concerns in the practical application of this system. For the enhancement of the serviceability of mega frame structures, a semi-active tuned mass damper (STMD) is developed in this study. To this end, a Magnetorheological (MR) damper is employed replacing passive damper as a semi-active damper to improve the control effect of a conventional TMD. Since a conventional finite element model of mega frame structures has significant numbers of DOFs, numerical simulation for investigation of control performances of a STMD is impossible by using the full-order model. Therefore, a reduced-order system using minimal DOFs, which can accurately represent the dynamic behavior of a mega frame structure, is proposed in this study through the matrix condensation technique To improve the efficiency of the matrix condensation technique, multi-level matrix condensation technique is proposed using the structural characteristics of mega frame structures. The efficiency and accuracy of the reduced-order control proposed in this study and the control performance of a STMD were verified using example structures.

• Journal of Korea Spatial Information System Society
• /
• v.9 no.3
• /
• pp.17-24
• /
• 2007

The noise problem is one of the major problems associated with large cities and is considered important factor not only in maintenance but also in development of cities. Accordingly, the noise map is being increasingly used in city planning and design. However, the existing two-dimensional noise maps only show regional, planar distribution of noise. This study presented a method to build a data model for analyzing and visualizing noise levels at fine scale considering the vertical distribution of noise in a building. By expanding the 2D topology concept used in conventional GIS to 3D, it suggested a 3D GIS data model that makes 3D spatial queries, analyses and visualization possible and applied the proposed approach to building a 3D noise information system. By building and testing the system, the study showed different functionalities including 3D spatial queries and 3D visualization of noise levels varying temporally or according as the height of sound-proof walls. In each case, the population exposed to noise was quantitatively computed to illustrate the potential in the areas of city planning and design.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.163-172
• /
• 2003

As concrete structures are getting larger, higher, longer, and specialized, it is more required to develop steel fiber concrete and apply to the real world. In this research, it is aimed to have fatigue strength examined, varying the steel fiber content by 0%, 0.75%, 1.00%, 1.25%, by experimental study of Two-spans Beam with Steel Fibrous with repeated loads. The ultimate load and the initial load of flexural cracking were measured by static test. In addition, the load versus strain relation, load versus strain relation, load versus deflection relation, crack pattern and fracture mode by increasing weight was observed. On the other hand, the crack propagation and the modes of fracture according to cycle number and the relation of cycle loading to deflection relation and strain relation was observed by fatigue test. As the result of fatigue test, Two-spans Beam without Steel Fibrous was failed at 60~70% of the static ultimate strength and it could be concluded that fatigue strength to two million cycle was around 67.2% by S-N curve. On the other hand, that with Steel Fibrous was failed at 65~85% of the static ultimate strength and it could be concluded fatigue strength to two million cycle around 71.7%.

• Journal of the Korea Concrete Institute
• /
• v.29 no.2
• /
• pp.189-200
• /
• 2017

Nonplanar structural walls with C-shaped and H-shaped sections have been used as an efficient lateral force-resisting system for building structures. Since the nonplanar walls are subjected to axial load and bending moments about two orthogonal axes, complicated section analysis is required for flexure-compression design. In the present study, a straightforward design method for biaxially loaded C- and H-shaped walls was proposed by modifying the existing load contour method for columns with symmetric solid sections. For this, a strain compatibility section analysis program that can calculate biaxial moment strengths of arbitrary wall section was developed and its validity was verified by comparing with existing test results. Then, through parametric study, the interaction of biaxial moments at constant axial loads in prototype C- and H-shaped walls was investigated. The results showed that, due to unsymmetrical geometry of the wall sections, the biaxial interaction was significantly affected by the moment directions and axial loads. From those investigations, non-dimensional contour equations of the biaxial moments at constant axial loads for C- and H-shaped walls were suggested. Further, design examples using the proposed contour equations were given for engineering practice.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.5
• /
• pp.1025-1037
• /
• 2015

Flexible base isolation bearings that separate superstructure from ground have been widely used in the construction field because they make a significant contribution to increasing the fundamental period of the structure, thereby decreasing response acceleration transmitted into the superstructure. However, the established bearing devices installed to uphold the whole building give rise to some problems involved with failure and collapse due to lack of the capacity as modern structures are getting more massive and higher. Therefore, this study suggests new isolation bearings assembled with additional restrainers enabled to reinforcing and recentering, and then evaluates their performance to withstand the seismic load. The superelastic shape memory alloy (SMA) bars are installed into the conventional lead-rubber bearing (LRB) devices in order to provide recentering forces. These new systems are modeled as component spring models for the purpose of conducting nonlinear dynamic analyses with near fault ground motion data. The LRB devices with steel bars are also designed and analyzed to compare their responses with those of new systems. After numerical analyses, ultimate strength, maximum displacement, permanent deformation, and recentering ratio are compared to each model with an aim to investigate which base isolation models are superior. It can be shown that LRB models with superelastic SMA bars are superior to other models compared to each other in terms of seismic resistance and recentering effect.