• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.1006-1009
• /
• 2015

Power-line communication technology is proposed to identify power transformers to serve customers in 3 phase -4 wires power distribution systems. Mathematical models for 3-phase power transformers, 3-phase wire lines, and customer loads are described to investigate the transmission characteristics of high frequency power line carrier. From the analysis, distribution line cable circuits have only a limited ability to carry higher frequencies. Typically power transformers in the distribution system prevent propagating the higher frequency carrier signal. The proposed method uses the limited propagation ability to identify the power transformer to serve customers. A novel power transformer identification system is designed and implemented. The system consists of a transmitter and a receiver with power-line communication module. Some experiments are conducted to verify the theoretical concepts in a big commercial building. Also some simulations are done to help and understand the concepts by using MATLAB Simulink simulator.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.1
• /
• pp.1-5
• /
• 2000

Co-fired resistors for high frequency MCM-C (Multi Chip Module-Cofired) were fabricated and measured their RF properties from DC to 6 GHz. LTCC (Low Temperature Co-fired Ceramics) substrates with 8 layers were used as the substrates. Resisters and electrodes were printed on the 7th layer and connected to the top layer by via holes. Deviation from DC resistance of the resistors was resulted from the resister pastes, resistor size, and via length. From the experimental results, the suitable equivalent circuit model was adopted with resistor, transmission line, capacitor, and inductor. The characteristic impedance $Z_{o}$ of the transmission line from the equivalent circuit can explain the RF behavior of the buried resistor according to the structural variation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.3
• /
• pp.419-428
• /
• 2000

Multiconductor transmission line(MTL) equations are solved by FDTD(Finite-Difference Time-Domain) method to predict crosstalk and fields to transmission line coupling on lossy multiconductor transmission lines terminated in arbitrary linear loads. Skin effect losses as well as dc losses are included in the analysis. In order to increase computational efficiency, the convolution integral of internal impedance of conductors and the line currents is computed by using Prony method. For boundary conditions of MTLs terminated in linear loads, state-variable formulation is adopted. The simulated results by FDTD method are compared with the measured ones obtained by using TEM cell. The predictions are in good agreement with the measurements. In addition, it has been found that skin effect losses as well as dc losses of the conductors should be included for accurate predictions on relatively high loss transmission lines such as PCB. It has also been found that dc losses and skin-effect losses affect late-time responses and early-time responses, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.11 s.102
• /
• pp.1099-1105
• /
• 2005

TRL error correction method is widely used for measuring high frequency device mounted on PCB. In order to correct error more precisely, the characteristic impedance of standard transmission line should be known mounted for error correction. The capacitance per the unit length of transmission line is calculated by using standard transmission line which terminate resistor additionally at previous method and the characteristic impedance of standard transmission line is calculated with fitting method according to frequency, but the characteristic impedance extracted by a manufacturing inaccuracy is influenced. In this study, a novel method can reduce the manufacturing inaccuracy using measured s-parameters and can extract more accurate characteristic impedance than the previous method.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.8
• /
• pp.37-44
• /
• 2004

This paper describes a new GaAs-based surface-micromachined microstrip line supported by dielectric post and air-gapped signal line with ground metal. This new type of dielectric-supported air-gapped microstripline(DAML) structure is developed using surface micromachining techniques to provide easy means of airbridge connection between the signal lines and to archive low losses at millimeter-wave frequency band with wide impedance range. Each DAMLs with the length of 5 mm are fabricated and the measured characteristics are compared with those of the conventional microstrip transmission line. These transmission lines are composed of 10 ${\mu}{\textrm}{m}$ height of signal line, post size of 10 ${\mu}{\textrm}{m}$ ${\times}$ 10 ${\mu}{\textrm}{m}$ and post height of 9 ${\mu}{\textrm}{m}$. By elevating the signal lines from the substrate using the micromachining technology, the substrate dielectric loss can be reduced Compared with of the conventional microstrip transmission line showing 7.5 dB/cm loss at 50 GHz, the loss can be reduced to 1.1 dB/cm loss at 50 GHz.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.559-562
• /
• 2017

In city, tracing of power transmission lines is difficult due to compound installation of overhead and underground lines, transposition, bad view caused by trees or big buildings. It is hard problem for electrical technician on site to trace power transformers or power lines to serve customers in 3 phase -4 wires power distribution systems. It is necessary that the correct and fast tracing method is required for load balancing among distribution lines. Old technology use to trace off-lines with high power impulse injection. Our proposed method use to trace live lines with very small power high frequency signal injection. Typical power transformers in the distribution system prevent propagating the higher frequency carrier signal. The proposed method uses the limited propagation ability to identify the power transformer to serve customers. Two end communication terminals are required to be synchronized between them for determination on electrically same phases. Challenging issue is to achieve synchronization without GPS providing synchronizing time. A novel power transformer and wire identification system is designed and implemented. The system consists of a transmitter and a receiver with power-line communication module. Some experiments are conducted to verify the theoretical concepts in a big commercial building. Also some simulations are done to help and understand the concepts by using MATLAB Simulink simulator.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.5
• /
• pp.879-886
• /
• 2008

This paper addresses the analysis and the design optimization of differential interconnects for Low-Voltage Differential Signaling (LVDS) applications. Thanks to the differential transmission and the low voltage swing, LVDS offers high data rates and improved noise immunity with significantly reduced power consumption in data communications, high-resolution display, and flat panel display. We present an improved model and new equations to reduce impedance mismatch and signal degradation in cascaded interconnects using optimization of interconnect design parameters such as trace width, trace height and trace space in differential flexible printed circuit board (FPCB) transmission lines. We have carried out frequency-domain full-wave electromagnetic simulations, time-domain transient simulations, and S-parameter simulations to evaluate the high-frequency characteristics of the differential FPCB interconnects. The 10% change in trace width produced change of approximately 6% and 5.6% in differential impedance for trace thickness of $17.5{\mu}m$ and $35{\mu}m$, respectively. The change in the trace space showed a little change. We believe that the proposed approach is very helpful to optimize high-speed differential FPCB interconnects for LVDS applications.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.4
• /
• pp.113-119
• /
• 1989

With optimal inductors shunted at the ends of the waveguide of RF exciting laser, the voltage variation can be reduced dramatically. If multiple inductores are shunted at the appropriate positions, almost the perfect RF uniformity is possible. All the optimum inductances are derived from the unique method of transmission line theory, which illustrates visually the whole variation of standing wave pattern along the hollow waveguide.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.229-229
• /
• 2007

나노결정 합금재료를 전력선 통신 커플러용 자심재료로 응용하기 위해서는 고주파 대역에서의 손실 특성이 제어되어야 한다. 즉 고속 전력선 통신을 위한 자심재료의 투자율 및 완화 주파수 등의 전자기적 특성은 30MHz까지 우수하고 안정적으로 유지되어야 하며, 높은 투자율 및 자속밀도, 공진주파수뿐만 아니라 낮은 전력손실 값을 가져야 한다. 따라서 본 연구에서는 나노결점 합금 리본 표면에 딥 코팅, 졸-겔법, 진공함침 등의 방법을 이용하여 PZT, $TiO_2$ 및 $SiO_2$ 등의 산화물 고저항층을 형성시켜 자기적 성질을 유지하면서 고주파 대역의 와전류 손실을 감소시켜 통신용 자심재료로의 응용성을 향상시키고자 하였다. PZT 슬러리의 제타전위 조절을 통해 최적의 분산조건을 얻을 수 있었고, 평균 150nm인 PZT 입자의 초미립자와 가소제, 분산제, 결합제의 첨가조건을 확립할 수 있었다. 딥-코팅은 슬러리 내 유지시간 10초, 인상속도 5mm/min로 30회 반복되었을 때 가정 우수한 특성을 나타내었으며, 고주파 대역에서의 손실 감소효과를 나타내었다. 그리고 졸-겔법에 의해 제조된 슬러리를 이용한 $TiO_2$와 $SiO_2$ 산화물 저항층 코팅을 통해 금속 알콕사이드의 혼합조건 및 저항층 형성용 슬러리의 제조조건을 확립하였고, 합금 리본표면에 균일하고 우수한 점착력을 가지는 저항층을 형성시킬 수 있었으며, 이에 따른 코어손실의 감소효과를 나타낼 수 있었다. 또한 진공 함침법을 통한 저항층 형성에서, $TiO_2$ 나노분말을 표면 저항층으로 코팅했을 때, 가장 높은 코어손실 감소효과를 나타내었다. 한편, 표면 저항층이 형성된 나노결정 합금으로 제조한 자심재료를 이용하여 전력선 통신용 비접촉식 커플러에의 적용과 시험을 통해 고주파 손실 감소효과에 의한 신호전송 특성과 전류특성을 향상시킬 수 있었다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.753-754
• /
• 2014

본 논문에서는 차량 충돌 예방 장거리 레이더용 고 이득 및 저 잡음 77GHz CMOS 저 잡음 증폭기를 제안한다. 이러한 회로는 2볼트 전원전압 및 77GHz의 주파수에서 동작한다. 이러한 회로는 TSMC $0.13{\mu}m$ 혼성신호/고주파 CMOS 공정($f_T/f_{MAX}=120/140GHz$)으로 설계되어 있다. 전체 칩 면적을 줄이기 위해 실제 수동형 인덕터 대신 전송선을 이용하였다. 제안한 회로는 최근 발표된 연구결과에 비해 34.33dB의 가장 높은 전압이득과 5.6dB의 가장 낮은 잡음지수 특성을 보였다.