• Journal of Welding and Joining
• /
• v.28 no.2
• /
• pp.39-46
• /
• 2010

IIn this study, used is the equivalent loading method based on the inherent strain to predict the welding deformation of panel members. Equivalent loads are computed from the inherent strain distribution around weld line, and then applied for the linear finite element analysis. Thermal deformation of panel members can be, of course, carried out through the rigorous thermal elasto-plastic analysis procedure but it is not practical in applying to predicting the welding deformation of large structures such as blocks found in a ship structure from view of computing time. The present equivalent load approach has been applied to flat plate model to verify the present approach, and to several curved plate models having the curvature in the welding direction to investigate the effect of the longitudinal curvature upon the weld-induced deformation. The results are compared with those by thermal elasto-plastic analysis. As far as the present results are concerned, it can be said that the present approach shows good agreement with the results by welding experiment and the rigorous thermal elasto-plastic analysis. The present approach has been also applied to predict the welding deformation of panel block as for application illustration to practical model.

• Computational Structural Engineering
• /
• v.10 no.3
• /
• pp.185-193
• /
• 1997

The order of the stress singularity that occurs at the termination of an interface between materials exhibiting bilinear stress-strain response under plane strain conditions has been calculated, The governing equation of elasticity together with traction-free boundary condition and interface continuity condition defines a two-point boundary value problem. The stress components near the free edge are assumed to be proportional to r/sup s-1/, with solutions existing only for certain values of s. Finding these values entails the solution of an eigenvalue problem. Because it has been impossible to integrate the differential equations analytically, the integration has been performed numerically with a shooting method coupled with a Newton improvement scheme.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.49-54
• /
• 2001

Measurement of welding residual stresses is one of important tasks to assess the structural integrity of welded structures. For operating components, especially, nondestructive techniques are required. By now, authors have proposed a new residual stress evaluation method, the bead flush method, where residual stresses are calculated from eigenstrain distribution determined by surface removal of reinforcement. In this paper, a brief description of the bead flush method is given and its utility and problem to be overcome are discussed. And also stabilization method of solution set of eigenstrain in inverse analysis is proposed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.2
• /
• pp.288-296
• /
• 1997

Curved beam elements with two nodes based on shallow beam geometry and strain interpolations are employed in eigenvalue analysis. In these elements, the displacement interpolation functions and mass matrices are consistent with strain fields. To assess the quality of the element mass matrix in free vibration problems, several numerical experiments are performed. In these analysis, both the inconsistent mass matrices using linear displacement interpolation function and the consistent mass matrices are used to show the difference. The numerical results demonstrate that the accuracy is closely related to the property of the mass matrix as well as that of the stiffness matrix and that the mass matrix consistent with strain fields is very beneficial to eigenvalue analysis. Also, it is proved that the strain based elements are very efficient in a wide range of element aspect ratios and curvature properties.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.4
• /
• pp.263-269
• /
• 2013

In this study, the strain based monitoring method to evaluate the lateral structural response of buildings is presented and an applicability of the proposed method is confirmed through the numerical study. It is assumed that the fiber Bragg grating(FBG) strain sensor is employed to measure the strain response of members due to the excellent properties such as multiplexing, and higher sampling frequency. These properties of FBG sensors is proper for buildings the a lot of sensors are required to monitor the reponses of those. FBG sensors measure the strain response of vertical members and are employed to calculate the curvatures of members using the measured strain responses. Then the lateral displacement, and lateral acceleration is evaluated based on the curvatures of vertical members. Additionally, these dynamic responses of buildings are used to evaluate the dynamic properties of buildings such as the natural frequencies and mode shapes using the frequency domain decomposition(FDD) method. Through the application of nine-story steel moment frame example structure, it is confirmed that the proposed method is appropriate to evaluate the lateral structural responses and dynamic properties of buildings.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.843-850
• /
• 2010

The dynamic modulus of elasticity of concrete can be determined nondestructively using impact echo test as prescribed in KS F 2437. The fundamental longitudinal frequency of the concrete cylinders with free-free boundary condition was estimated by the wavelet transform theory. The advantage of the wavelet transform over either a pure spectral or temporal decomposition of the signal is that the features of the pertinent signals can be characterized in the time-frequency plane. For the concrete mix design utilized in this study, no significant difference between the dynamic and the static moduli of elasticity was observed. This was contrary to the perceived general notion of having the dynamic modulus considerably higher than the static modulus. It has been shown that the modulus from static and dynamic by impact echo test are comparable to each other fairly well, when the effect of strain level was properly taken into account. In this experimental test, it was shown that the dynamic modulus is approximately equal to the tangent modulus at $1{\times}10^{-4}$ strain level.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.5
• /
• pp.67-75
• /
• 2014

In this paper, isotropically consolidated drained triaxial compression test device installed with bender elements is used to measure stress, stain, and shear wave velocity, from which the characteristics of shear strength and Poisson'ratio are investigated. The results show that there is a unique relationship between maximum shear modulus determined from shear wave velocity and effective vertical stress at failure, which is defined as the sum of vertical and radial stresses at failure. The correlation is very useful since it is possible to predict the shear strength and internal friction angle from shear wave velocity. In addition, Poisson's ratio is determined from measured axial and volumetric strains. It is demonstrated that the range of measured Poisson's ratio is between 0.15 and 0.6, and increases with the axial strain. The ratios at axial strains smaller than 0.2% corresponds to the range recommended in design codes, which are approximately from 0.3~0.35. However, at axial strains exceeding 1%, the measured ratios are between 0.5 and 0.6. It is therefore shown that use of ratios commonly used in practice will result in pronounced underestimation at large strains.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.9
• /
• pp.17-27
• /
• 2015

We perform a series of experimental tests to evaluate whether the shear strength of clean sands can be reliably predicted from shear wave velocity. Isotropic drained triaxial tests on clean sands reconstituted at different relative densities are performed to measure the shear strength and bender elements are used to measure the shear wave velocity. Laboratory tests reveal that a correlation between shear wave velocity, void ratio, and confining pressure can be made. The correlation can be used to determine the void ratio from measured shear wave velocity, from which the shear strength is predicted. We also show that a unique relationship exists between maximum shear modulus and effective axial stress at failure. The accuracy of the equation can be enhanced by including the normalized confining pressure in the equation. Comparisons between measured and predicted effective friction angle demonstrate that the proposed equation can accurately predict the internal friction angle of granular soils, accounting for the effect of the relative density, from shear wave velocity.

• Journal of the Korean Society for Railway
• /
• v.18 no.2
• /
• pp.127-138
• /
• 2015

It is important to evaluate the stiffness characteristics of compacted subgrade soil under track that is loaded dynamically. Using a mid-size Resonant Column test apparatus, normalized shear modulus and shear modulus variation with changing of confining pressure were investigated with change of degree of saturation (DOS). From an analysis of the test results, it was verified that the maximum shear modulus decreased with increases of DOS. However, normalized shear modulus increased with increases of DOS. Using the test results, a relation of G~${\gamma}$~DOS can be constructed and characterized. In the future, by performing tests with soils used as trackbed broadly in the field, a prediction model for DOS~G~${\gamma}$ can be proposed.

• Proceedings of the Korean Information Science Society Conference
• /
• 2007.10d
• /
• pp.41-45
• /
• 2007

기존의 생체인식 기술들은 노화에 따른 신체부위의 변형으로 인해 인식률 저하를 초래할 수 있으며 인식단계 시 눈과 같은 신체의 민감한 부분을 빛에 노출시키는 등의 불쾌감을 이용자에게 초래할 수 있다. 본 논문에서는 기존 생체인식 시스템이 갖는 이러한 문제들을 보완하기 위해 손가락 정맥영상을 이용한 생체인식 시스템을 제안한다. 손가락 정맥의 경우 인식 절차가 단순하면서도 개인마다 고유한 특징을 충분히 포함하고 있다. 또한 인체 내부에 존재하는 특징으로 인해 외상이나 노화로 인한 변형의 가능성이 적으며 촬영 시 이용자의 거부감이나 불쾌감을 최소화 할 수 있다.