• Electrical & Electronic Materials
• /
• v.10 no.2
• /
• pp.141-149
• /
• 1997

L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ powders were prepared by both GNP(Glycine-Nitrate Process) and solid state reaction method in various of calcination temperature(800-1000.deg. C) and time in air. Also, L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ cathode contacts on YSZ(Yttria-Stabilized Zirconia) substrate were prepared by screen printing and sintering method as a function of sintering temperature(1100-1450.deg. C) in air. Sintering behaviors have been investigated by SEM(Scanning Electron Microscope) and porosity measurement. Compositional and structural characterization were carried out by X-ray diffractometer and ICP AES(Inductively Coupled Plasma-Atomic Emission Spectrometry) analysis. Electrical characterization was carried out by the electrical conductivity with linear 4 point probe method. As the calcination period increased in solid state reaction method, L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ phase increased. Although L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ single phase was obtained only for 48hrs at 1000.deg. C, in GNP method it was easy to get single and ultra-fine L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ powders with submicron particle size at 650.deg. C for 30min. The particle size and thickness of L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ cathode contact by solid state reaction method did not change during the heat treatment, while those by GNP method showed good sintering characteristics because initial powder size fabricated from GNP method is smaller than that fabricated from solid state reaction method. Based on enthalpy change from thermodynamic data and ICP-AES analysis, it was suggested to make cathode contact in composition of (L $a_{0.7}$S $r_{0.3}$)$_{0.91}$ Mn $O_{3}$ which have little second phase (L $a_{2}$Z $r_{2}$ $O_{7}$) for high efficient solid oxide fuel cells applications. As (L $a_{0.7}$S $r_{0.3}$)$_{0.91}$Mn $O_{3}$ cathode contact on YSZ substrate was sintering at 1250.deg. C the temperature that liquid phase sintering did not occur. It was possible to obtain proper cathode contacts with electrical conductivity of 150(S/cm) and porosity content of 30-40%.m) and porosity content of 30-40%.

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.4
• /
• pp.336-347
• /
• 1985

Soils and rice plants subject to smoke from the Jang-hang Smelter were samples at two depths to assess the nature and extend of Cd, Cu, Pb, and Zn contamination, particularly with respect to distance from pollution source. Soils at east site within 1km of the center of the smelter were highly contaminated with Cd, Cu, Pb, and Zn. Metal levels in the smoke-polluted area were higher in surface soil than in subsurface soil, and decreased rapidly with distance reaching nearly background levels at 5km from pollution source. A position correlation was found between contents of total and 0.1 N HCl-extractable, or 1.0N $CH_3COONH_4$- extractable heavy metals in surface soils of pollution. Contents of heavy metals in soils were positively correlated with soil organic matter and cation exchange capacity. The contents of heavy metals in brown rice collected from the paddy field around the Jang-hang Smelter were in the range of 0.23-1.33 ppm for Cd, 2.39-6.25 for Cu, 0.95-8.32 ppm for Pb and 14.60-27.31 for Zn. The contents of Cd, Cu, and Zn in rice straw were positively correlated with those in the brown rice. Negative correlation was found between the contents of Cd, Cu, Pb, and Zn in brown rice and the distance from the source.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.116-123
• /
• 2019

Thermal batteries are also called molten-salt batteries as the electrolyte is mainly composed of molten salt. The molten-salt electrolyte is a solid that does not conduct electricity at room temperature, but when it is melted by a pyrotechnic heat source, it becomes an excellent ionic conductor. Thermal batteries are a kind of pyrotechnic battery because they operate only when the solid electrolyte is melted by the heat energy provided by pyrotechnic materials. Pyrotechnic components used in a thermal battery include heat sources, fuse strips, and an igniter. The reliability of these pyrotechnic components critically affects the reliability and performance of the battery that must supply electricity stably to guided munitions even under extreme environmental conditions. Different igniter types offer different advantages: notch-type igniters offer improved ignition probability, whereas film-type igniters offer improved safety. The addition of metal oxides to the heat paper could improve the burn rate, and the ignition reliability could be greatly improved by using it with a flame igniter at the same time. Using a two-step reduction process, high-purity Fe particles in coral form can be safely obtained.

• Clean Technology
• /
• v.26 no.4
• /
• pp.293-303
• /
• 2020

According to the World Health Organization (WHO), air pollution is a typical health hazard, resulting in about 7 million premature deaths each year. Sulfur dioxide (SO2) is one of the major air pollutants, and the combustion process with sulfur-containing fuels generates it. Measuring SO2 generation in large combustion environments in real time and optimizing reduction facilities based on measured values are necessary to reduce the compound's presence. This paper describes the concentration measurement for SO2, a particulate matter precursor, using a wavelength modulation spectroscopy (WMS) of tunable diode laser absorption spectroscopy (TDLAS). This study employed a quantum cascade laser operating at 7.6 ㎛ as a light source. It demonstrated concentration measurement possibility using 64 multi-absorption lines between 7623.7 and 7626.0 nm. The experiments were conducted in a multi-pass cell with a total path length of 28 and 76 m at 1 atm, 296 K. The SO2 concentration was tested in two types: high concentration (1000 to 5000 ppm) and low concentration (10 ppm or less). Additionally, the effect of H2O interference in the atmosphere on the measurement of SO2 was confirmed by N2 purging the laser's path. The detection limit for SO2 was 3 ppm, and results were compared with the electronic chemical sensor and nondispersive infrared (NDIR) sensor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.10
• /
• pp.911-920
• /
• 2016

For the pitch and yaw axis attitude control of launch vehicle, thrust vector control which changes the direction of thrust during the engine combustion is commonly used. Hydraulic actuation system has been used generally as a drive system for the thrust vector control of launch vehicles with the advantage of power-to-weight ratio. Nowadays, due to the developments of highly efficient electric motor and motor control techniques, it has done a lot of research to adopt electro-mechanical actuator for thrust vector control of small-sized launch vehicles. This paper describes system design and test results of the prototype of direct drive electro-mechanical actuation system which is being developed for the thrust vector control of $3^{rd}$ stage engine of KSVL-II.

• Journal of the Korean Ceramic Society
• /
• v.40 no.5
• /
• pp.481-487
• /
• 2003

A technique for determination of proportions of char, coal ana coke is needed in order to monitor pulverized coal injection performance in operating blast furnace. Quantitative X-ray powder diffraction analysis can be applied to the problem providing that structural information on carbonaceous materials, coal, char, coke and their mixture are known. Chars were prepared from a coal at different temperatures (1000∼1400$^{\circ}C$) and were characterised by X-Ray powder Diffraction (XRD). The XRD result gave crystallite size (height Lc and diameter, La), aromaticity, number of (002) plane in carbon, and d-spacing. As a result, with increasing heat treat temperature of char, Lc$_{(002)}$, La$_{(10)}$ and number of (002) plane in carbon were increased, and d-spacing and FWHM(Full With Half Maximum) were decreased. Result of prediction of amount of char from the mixtures (char, coke and ore) based on the Lc$_{(002)}$ information of two mixtures (coke and char) showed very close values expected.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.40.2-40.2
• /
• 2011

초경합금은 경도가 높은 재료를 말하며 일반적으로는 탄화텅스텐(WC)계 재료를 말한다. 국내 현재 초경합금 동향은 반도체 산업, 내마모성 공구, 절삭공구, 금형 등 많은 분야에 사용되어지고 있다. 또한 최근 들어 FSW (Friction Stir Welding, FSW)기술이 발전함에 따라 접합기술개발이 다양화되면서 FSW Tool의 고성능의 초경 재료가 요구되어지며 장수명의 Tool개발이 되어야 한다. 국내에서는 초경 합금 재료로 사용되어지고 있는 텅스텐 카바이드(WC)와 코발트(Co)를 이용하여 많은 연구가 진행되었다. 본 실험에서는 텅스텐 카바이드와 코발트 및 몰르브덴 카바이드를 혼합하여 소결체를 제조하였다. 실험에 사용된 텅스텐 카바이드는 높은 경도를 가지고 강한 취성을 나타내며, 소결에 어려운 단점이 있다. 이러한 단점을 코발트와 몰리브덴 카바이드를 첨가하여 소결온도를 낮춰주는 역할과 액상 소결시 텅스텐카바이드 입자사이에 침투하여 액상소결에 의한 치밀화가 가능하게 해주며 인성이 향상되어 고인성 재료를 만들 수 있었다. 본 실험에서는 합성과 치밀화가 동시에 진행되는 SPS (Spark Plasma Sintering:SPS) 장비를 이용하여 실험을 진행하였다. 이 방법은 방전플라즈마 소결 공법으로, 기존의 연소법과 열간 가압기술(Hot-press, HIP)을 결합한 방식으로 단 시간, 단일공정으로 치밀한 소결체를 얻을 수 있는 장점이 있다. 본 연구에서는 $WC-5Mo_2C$-5wt%Co 소결체 제조를 위해 원소 분말을 Horizontal ball milling 혼합하였다. 균일하게 혼합된 분말을 흑연다이에 충진하여 펄스전류와 기계적 압력을 동시에 가하여 $WC-5Mo_2C-5Co$ 복합재료를 제조하고 소결체의 밀도, 순도, 상변태, 미세조직 등을 분석 및 평가하였다. SPS공정 조건은 고진공하에서 $1,200^{\circ}C$-60MPa, 펄스비 12:1 조건으로 수행하였으며, 얻어진 $WC-5Mo_2C-5Co$ 소결체의 상대 밀도는 98%이상 이였다. 또한, 결정립 크기는 약 400 nm였으며, 경도는 $2,453kg/mm^2$를 나타내었다.

• Resources Recycling
• /
• v.10 no.5
• /
• pp.16-21
• /
• 2001

Ultrafine $Mg(OH)l_2$and MgO powders were recovered from the waste solution containing $Mg^{++}$ which was a by-product of SHS (Self-propagating High temperature Synthesis)process. The optimum experimental conditions to prepare $Mg(OH)_2$were 13.0 of pH and 0.7M of $Mg^{++}$ content with addition of 9M of KOH as a pH regulator in acid leaching solution. Complete pre-cipitation of Mg(OH)$_2$from $Mg^{++}$ was realized at that condition. The dehydration reaction of the prepared Mg(OH)$_2$was studied by DSC, and the result was used for calcination process. In order to obtain MgO powder, dried Mg(OH)2 powder was calcined at $400~450^{\circ}C$. Particle size and shape of the prepared $Mg(OH)_2$and MgO powder was similar to those of the commercial powders.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.323-327
• /
• 2009

To extract hydrogen for stack, fuels such as LPG and LNG were reformed in the fuel processor, which is comprised of desulfurizer, reformer, shift converter, CO remover and steam generator. All elements of fuel processor are integrated in a single package. Highly active catalysts (desulfurizing adsorbent, reforming catalyst, CO shift catalyst, CO removal catalyst) and the various burners were developed and evaluated in this study. The performance of the developed catalysts and the commercial ones was similar. 1 kW, 5 kW class fuel processor systems using the developed catalyst and burner showed efficiency of 75 %(LHV, for LNG). The start-up time of the 1 kW class fuel processor was less than 50 minutes and its volume including insulation was about 30 l. The start-up time of 3 kW and 5 kW class fuel processors with the volume of 90 l and 150 l, respectively, was about 60 minutes. In the case of LPG fuel, efficiency, volume and start-up time of 1kW class fuel processor showed 73 %(LHV), < 60 l and < 60 min, respectively. Advanced fuel processor showed more highly efficiency and shorter start-up time due to the improvement of heat exchanger and operating method. 1 kW and 3 kW class fuel processors have been evaluated for reliability and durability including with on/off test of developed catalysts and burner.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.146.1-146.1
• /
• 2011

석탄가스화복합발전(IGCC)공정에서 가스화기를 거쳐 생성된 합성가스로부터 $CO_2$를 효과적으로 분리/회수하기 위해 가스 고형화법을 제안하였다. 가스 하이드레이트 형성과정에서의 반응특성을 살펴보기 위하여 반응시간에 따른 가스소모량과 기상의 $CO_2$ 조성 변화를 측정하였다. 순수계와 촉진제 첨가계 (TBAB (10, 40 wt%), TBAF (10, 34 wt%), THF (4, 19 wt%))에 대하여 하이드레이트 생성 후의 기상과 하이드레이트상의 $CO_2$ 조성을 측정하였으며, 그 결과 하이드레이트 형성법에 의해 고농도의 $CO_2$가 하이드레이트상에 포집되는 것을 확인하였다. 가스 소모량 측정실험에서는 THF 19.1 wt%를 첨가하였을 때 가장 큰 소모량을 보였으며, TBAF 10 wt%를 첨가하였을 때 가장 적은 가스소모량을 보였다. $CO_2$ 조성 변화 실험에서는 가스 소모량 실험과 마찬가지로 THF 19.1 wt%를 첨가하였을 때 가장 큰 조성변화를 보였다. 이는 THF의 첨가로 인하여 가스 하이드레이트로의 전환율 증가로 많은 양의 $CO_2$ 기체가 하이드레이트 상에 포집되었음을 나타낸다. 속도론적인 측면에서는 모든 실험조건에서 하이드레이트 형성반응이 1시간 이내에 대부분 종결되는 것을 볼 수 있었다. 또한 $^1H$-NMR을 통하여 혼합가스 하이드레이트의 구조적인 분석을 진행하였다. 본 실험에서 얻어진 결과는 가스 하이드레이트 형성법을 이용한 합성가스 분리 공정 개발에 중요한 기초자료가 될 것으로 사료된다.