• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.6-11
• /
• 2005

During the acceptance test of KTX, lateral vibration of carbody at the tail of the train was found. The carbody lateral vibration was occurred on a straight line in the winter season. We analysis to find the cause of the lateral vibration and the countermeasure. The analysis results show that lateral stiffness of air spring is the most important parameter to cause the carbody lateral vibration. The lateral vibration is occurred at frequency range $0.5{\sim}0.6Hz$ with a negative damping value. We also blow that natural frequency of lateral vibration increase with the train speed up to 1Hz at 300km/h.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.191-198
• /
• 2009

There are almost no studies on verification of requirements for high speed rolling stocks by means of RAM goals and on setting RAM goals by means of verification on practical reliability, availability and maintainability for high speed rolling stocks though they are covered in specification of an order that RAM goals asked of rolling stocks are shown for gaining high quality of them and availability when they are in operation. This study is for estimating number of high speed train-sets that would be supplementarily placed an order through verification of RAM goals of a project for the introduction of KTX-II 100 cars. It verify that optimized requirements for high speed rolling stocks by relatively comparison with between requirements for train-sets through setting RAM goals and requirements for train-sets through analysis of prospects for management balance with high speed rolling stocks.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.953-955
• /
• 2014

최근 차량 충돌 방지를 위한 다양한 기술이 상용화되고 있다. FMCW 기반의 레이더 시스템은 구현의 용이성으로 많은 상용차에서 전면 충돌 방지 시스템에 적용되고 있다. 측면 충돌 방지를 위한 BSD(Blind Spot Detection)와 차선변경 보조 시스템(LCA, Lane Change Assistant system)에서는 전방 레이더보다 인식거리가 줄어들고 갱신율이 낮아지므로 고속 FFT 등을 수행하는 신호처리부를 저가격으로 설계가 가능할 것이다. 본 연구에서는 TI사의 MCU인 F28335를 사용하여 근거리를 인식하는 신호처리부를 설계하였다. 이 MCU는 16채널 12bit ADC와 68KB RAM 및 512KB 플래시 메모리를 내장하고, 150MHz 부동소수점 연산을 지원하여 단일 칩으로 신호처리부의 구현이 가능하다. 구현된 시스템은 20m내외의 거리에 있는 장애물에 대하여 10Hz로 갱신이 가능하여 BSD를 위한 기본 기능이 확인되었다. 이러한 구현은 이전의 고가의 DSP나 FPGA를 사용하지 않고 15$이내의 단일 MCU와 간단한 아날로그 회로로 설계되어 저가격의 시스템으로 상용화가 가능할 것이다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.488-489
• /
• 2009

In this paper, a FlexRay module and gateway is developed for high speed in-vehicle network. Speed of FlexRay is 10 times higher than that of CAN. In this paper, FlexRay module is implemented using MC9S12XF512 micro-controller and gateway converting CAN message to FlexRay message.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.3081-3083
• /
• 2005

한국형 고속전철차량의 자동제어 구현을 위해서 우선 다양한 종류의 장치들로부터 상태정보(Line Voltage-열차가선전압, Bogie Hunting, Preset Speed, PWM, Train Velocity, Brake Pressure, Reservoir Pressure)를 취득해야하며, Main Process Unit(MPU)에서의 고속 Data 처리를 위해서 취득한 Analog Data를 신속하게 Digital Data로 변환해야 한다. 또한 열차내의 특수한 조건(Noise, Vibration)에서도 안정적인 데이터의 취득을 만족시켜야한다. 이와 같은 상황을 고려한 독자적이 통합형 데이터 취득 장치 -Integrated Data Acquisition Board(IDAB)-의 설계방안을 제시하였다.

• Journal of the Korean Society for Railway
• /
• v.10 no.2 s.39
• /
• pp.146-152
• /
• 2007

The ride comfort is more important in the train speedup. Generally, it is defined as the vehicle vibration. There are many studies on evaluation method of ride comfort for railway. But the ride comfort for Korean high speed train(HSR 350x) has been assessed by statistical method according to UIC 513R. It is impossible for HSR 350x to run at constant speeds above 310km/h during 5 minutes required in UIC 513R because of the same operational condition as KTX and the design limitation of infrastructures. The ride indices data had been acquired from 80 to 310km/h through the on-line test. The present study has suggested the methodology for the estimation of the ride indices at high speed above 310km/h by using those obtained below 310km/h and reviewed the ride comfort for HSR 350x in these speeds.

• Journal of the Korean Society for Railway
• /
• v.13 no.4
• /
• pp.376-381
• /
• 2010

In this study, field measurements on KTX, Nuriro and TTX train have been conducted at Kyeongbu and Honam line to predict the wind gust under train at the speed-up of major conventional railway lines using Kiel-probe array and multi-channel pressure scanning system. The results show that the average wind velocity during train passage normalized by train speed is independent to train speed, thus the wind gust for a given train type at the speed-up condition could be predicted. The relationship between the shape of underbody and the characteristics of the underbody wind gust has been discussed.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1012-1013
• /
• 2008

경부고속철도의 개통과 함께 서울-부산 간 운행시간이 새마을호 기준 4시간 30분에서 2시간으로 단축되는 등 획기적인 시간 절감을 이루었으나 이는 고속철도가 운행되는 지역에 국한된 것이다. 이에 고속철도 비 수혜지역의 운행시간 단축을 위해 기존선 속도향상이 요구되며, 이러한 목적으로 한국철도기술연구원에서는 틸팅열차를 개발하여 시운전 10만Km를 목표로 시험운행중이다. 또한 한국철도공사에서는 이와 유사한 목적으로 기존선 신호시스템인 ATS 시스템을 차상신호시스템(ATP)으로 개량하는 사업이 추진되고 있다. 현재 틸팅열차에는 기존의 ATS(자동열차정지장치) 차상장치만을 장착하여 차량의 성능 확인을 위한 시험 및 시운전을 우선적으로 추진하고 있는 상태이며 이러한 ATS 차상장치는 160km/h 이하의 속도에서만 본연의 기능이 유지되고, 그 이상의 속도에서는 현실적으로 사용이 어렵기 때문에 틸팅열차의 목표속도인 200km/h에서 적합하게 시험하기 위해서는 적합하지 않다. 따라서 한국철도공사에서 추진하고 있는 ATP 구축사업의 지상설비와 연계될 수 있는 ATP 차상장치를 설치하여 시험을 하여야 한다. 본 논문에서는 이를 위하여 ATP 차상장치의 틸팅열차 적용에 대한 연구를 추진한 결과를 발표하고자 한다.

• Journal of the Korean Society for Railway
• /
• v.9 no.1 s.32
• /
• pp.36-42
• /
• 2006

Studied was a strategic plan for the Korean High-Speed Train system to penetrate the Chinese railway market in exchange of the technology of KHST. Firstly, taken was a glance at Chinese Government plans to extend total length of his railway lines and to construct the Beijing~Shanghai high-speed railway line. Then, disparity of railway technology in Korea and China was reviewed. From the review, SWOT Analysis were carried out to penetrate the foreign markets. Countermeasures to cope with SWOT were also considered. Strategical governmental supports and the establishment of the special organization to be in charge of penetration of KHST into foreign markets were proposed. Finally, also proposed was the transfer of KHST technology to Chinese counterparts in exchange of tangible benefits for Korean side. The benefits may include (1) adoption of KHST as the type of rolling stock for the Beijing~Shanghai line, (2) guarantee of participation in the project and royalty for the KHST technology used for the future high-speed railway line construction, (3) prior written approval and partnership when making its way to third country, and (4) participation of Korean construction companies in Chinese railway construction project, etc. Adoption of KHST in China indeed gives chance to integrate the high-speed railway network after reunification of Korean peninsular, and enhance the economic ties between two countries.

• Journal of the Korean Society for Railway
• /
• v.10 no.5
• /
• pp.487-491
• /
• 2007

When constructing a high-speed railroad, the reduction of the distance between track centers and the width of track bed will save the construction cost. However the shortening the distance between track centers may cause the stability problems due to higher wind pressure. Therefore the extensive technical review and aerodynamical study should be performed to determine the adequate distance between track centers. In this study, the impact that the increase in wind pressure due to the change of aerodynamic phenomena with the change of the distance between track centers may have on two trains passing by each other was predicted, and the stability of train operation was analyzed in order to review the distance between track centers suitable to Honam HSR trains. And we estimated the aerodynamical effects by the results of the real train experiments.