• The Journal of the Acoustical Society of Korea
• /
• v.11 no.4
• /
• pp.5-13
• /
• 1992

The vibration of a vehicle, which is caused by and transmitted from the engine, has significant effect on the ride comfort and the dynamic characteristics of the engine mount system has direct influence on the vibration and noise of the vehicle. This paper examines the body shake caused by the engine excitation force on engine key-off of a jeep by experiment and computer simulation using a general purpose mechanical system program, DADS. The computer simulation model consists of the engine, body including frame, and front and rear axles and each axle has right and left tires. The force element between body and suspension is modeled as a combination of suspension spring and damper, and the unsprung mass has roll and pitch motion. The body shake obtained from experiment was compared with the result of computer simulation. Parametric study of the body shake on engine key-off is performed with changing the stiffness of engine mount rubber, the engine mount installation angle and position of engine mounts by using the verified computer simulation model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1521-1528
• /
• 2011

We studied the material properties for reliability improvement in finite element analysis results for a nitrile butadiene rubber hub-bearing seal and for a carbon-filled rubber mount used in a vehicle. It was difficult to measure the material properties of hundreds of types of rubber for the mount design. Thus, we suggested that the engineering stressstrain relations from pure shear test data could be synthesized by using simple tension data and Poisson's ratio. We defined Poisson's ratio by using a function of principal stretches to synthesize the stress-strain relations for a pure shear test. A transformation of the pure shear data was applied to the experimental values to obtain the predicted results when the strain approaches 100%. In the finite element analysis for the contact force of a hub-bearing seal, the strain results that used the transformation of the pure shear data and simple tension data almost corresponded to the experimental values. Ogden constants were used to analyze.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.927-932
• /
• 2001

Rubber has high damping and can be formed as various shape according to specific purpose. So, Rubber has widely used as isolation mounts. However, there are still a lot of difficulties in understanding of static and dynamic characteristics of compressed and shear rubber mounts. In this paper, Static characteristics of the rubber isolation mount are observed by the analytical method and FEM. Also dynamic characteristics of rubber mount under compression and shear strain are investigated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1669-1674
• /
• 2012

A commonly analytical estimation of fatigue life on rubber components is using fatigue life equation based on various fatigue test results. However, such method has very restricted applicability in actual designing processes because performing fatigue tests requires a lot of time and money. In addition, non-standard rubber materials and their randomness make it hard to make databases. In this paper, the other fatigue life estimation method using tearing energy was suggested. We performed static and dynamic tearing test about automotive vibration rubber materials and a finite element formulation using a virtual crack to calculate the tearing energy of rubber components with complicated shapes. To using the suggested method, fatigue life of an automotive motor mount has been estimated and verified the reliability of this method by using comparison between the estimated values and the actual fatigue life.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.6
• /
• pp.927-933
• /
• 2023

In modern times, with advances in semiconductor technology such as electronic devices, the need to improve the quality of onboard equipment with advanced electronic parts in automobiles, drones, airplanes, projectiles, and various fields, and reduce the impact of various disturbances on onboard equipment is becoming more important. Vibration control through hardware must be determined to prevent damage and improve quality to equipment operating in various environments such as automobiles, drones, airplanes, and projectiles. This study focuses on the study of vibration damping systems to protect mounted equipment from various disturbances and improve stability. Dynamic characteristics analysis, including compressive stiffness, damping rate, and frequency response, and vibration characteristics in the frequency domain of rubber dampers were identified through FEM analysis to identify the characteristics of rubber dampers. Through these findings, we would like to present the criteria for selecting a suitable rubber damper under various disturbance conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.6
• /
• pp.848-859
• /
• 2004

Mechanical testing methods to determine the material constants for large deformation nonlinear finite element analysis were demonstrated for natural rubber. Uniaxial tension, uniaxial compression, equi-biaxial tension and pure shear tests of rubber specimens are performed to achieve the stress-strain curves. The stress-strain curves are obtained after between 5 and 10 cycles to consider the Mullins effect. Mooney and Ogden strain-energy density functions, which are typical form of the hyperelastic material, are determined and compared with each other. The material constants using only uniaxial tension data are about 20% higher than those obtained by any other test data set. The experimental equations of shear elastic modulus on the hardness and maximum strain are presented using multiple regression method. Large deformation finite element analysis of automotive transmission mount using different material constants is performed and the load-displacement curves are compared with experiments. The selection of material constant in large deformation finite element analysis depend on the strain level of component in service.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1199-1203
• /
• 2011

Nanocomposites were prepared through the compounding of rubber and clay. Measurements of the static and dynamic mechanical properties of different compositions over a temperature range $70-100^{\circ}C$ showed that the mechanical properties of these rubber/clay nanocomposites are superior to those of existing rubber materials. In this study, by using the parameter of the maximum Green.Lagrange strain appearing at certain locations, the relationship between fatigue life and maximum Green.Lagrange strain, and the correlations between test-piece tests and bench tests of actual rubber components are proved. In order to predict the fatigue life of rubber components at the design stage, a simple procedure of life prediction is suggested. The predicted fatigue lives of the rubber engine mounts agree fairly well with the fatigue lives determined experimentally.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.6
• /
• pp.553-562
• /
• 2013

Vehicle vibrations arise from engine and road surface excitations. The engine mount system of a passenger car sustains the engine weight and insulates the excitation force from the engine system. The dynamic properties of viscoelastic material used for the vehicle engine mounts have large variation due to environmental factors such as environmental temperature and humidity etc. The present study aims to investigate the variability of dynamic characteristics in rubber engine mounts considering both environmental temperature change and material model errors/uncertainty. The engine mounts for a passenger car were modeled using finite element method. Then, the dynamic stiffness variability of the engine mounts were estimated using Monte Carlo simulation method. In order to estimate the variations in the storage and loss moduli of the viscoelastic materials, the material properties of the synthetic rubber were expressed as a fractional-derivative model. Next, in order to simulate the uncertainty propagation of the dynamic stiffness for the engine mounts due to the storage and loss moduli variations, the Monte Carlo simulation was used. The Monte Carlo simulation results showed large variation of the engine-mount stiffness along frequency axis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.17-23
• /
• 2006

Rubber materials have the nonlinear, large deformation and viscoelastic behavior. W.D. Kim et al. studied these characteristics through the static, fatigue, dynamic, aging and viscoelastic test. This paper discussed that the properties of engine mounting rubber, such as static stiffness, fatigue life and damping factor, are predicted based on CAE by using material properties acquired by the report of Kim et al. In result, the static stiffness of engine mounting rubber is predicted approximately in comparison with test value. Also, it was confirmed that the relationship of fatigue life and Green-Lagrange strain in specimen was the valid tool to predict the fatigue life of engine mounting rubber. From the results of transient viscoelastic analysis the damping factor changed rapidly at the range less than 8hz.

• Journal of Applied Reliability
• /
• v.6 no.2
• /
• pp.135-150
• /
• 2006

Rubber material properties and lifetime evaluation are very important in design procedure to assure the safety and reliability of the rubber components. This paper discusses the failure mechanism and material tests were carried out to predict the useful lifetime of NBR and EPDM for compression motor, which is used in refrigerator component. The heat-aging process leads not only to mechanical properties change but also to chemical structure change so called degradation. In order to investigate the aging effects on the material properties, the accelerated test were carried out. The stress-strain curves were plotted from the results of the tensile test for virgin and heat-aged rubber specimens. The rubber specimens were heat-aged in an oven at the temperature ranging from $70^{\circ}C\;to\;100^{\circ}C$ for a period ranging from 1 to 180 days. Compression set results changes as the threshold are used for assessment of the useful life and time to threshold value were plotted against reciprocal of absolute temperature to give the Arrhenius plot. By using the compression set test, several useful lifetime prediction equations for rubber material were proposed.