• Journal of the Korean Vacuum Society
• /
• v.4 no.4
• /
• pp.402-406
• /
• 1995

MOS(금속 산화막 반도체 접합) 소자가 방사선에 노출되면, 산화막재에 양의 공간전하가 생성되고 Si-SiO2 계면에 계면준위가 생성된다. MOS 커패시터의 방사선 조사효과를 방사선 피폭량과 산화막의 두께를 달리하는 시편에서 정전용량과 전류변화를 측정하여 고찰하였다. 정전용량-바이어스 전압 특성 실험결과로부터 플렛밴드 전압 및 계면상태밀도를 계산하였다. 또한 전압-전류 특성은 방사선 조사로 산화막내에 생성된 양의 공간전하와 Si-SiO2 계면에 포획된 전하에 의해서 설명이 가능하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.12
• /
• pp.2899-2904
• /
• 2015

This paper introduces about the effect on $I_{DS}-V_{GS}$ characteristic of transistor that interface trap charge is created by damage due to heat in a 3D sequential inverter. A interface trap charge distribution in oxide layer in a 3D sequential inverter is extracted using two-dimensional device simulator. The variation of threshold voltage of top transistor according to the gate voltage variation of bottom transistor is also described in terms of Inter Layer Dielectric (ILD) length of 3D sequential inverter, considering the extracted interface trap charge distribution. The extracted interface trap density distribution shows that the bottom $HfO_2$ layer and both the bottom and top $SiO_2$ layer were relatively more affected by heat than the top $HfO_2$ layer with latest process. The threshold voltage variations of the shorter length of ILD in 3D sequential inverter under 50nm is higher than those over 50nm. The $V_{th}$ variation considering the interface trap charge distribution changes less than that excluding it.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.620-624
• /
• 2014

In this study, the electrical characteristics of Ni/CNT/$SiO_2$ structures were investigated in order to analyze the mechanism of carbon nanotubes in 4H-SiC MIS device structures. We fabricated 4H-SiC MIS capacitors with or without carbon nanotubes. Carbon nanotubes were dispersed by isopropyl alcohol. The capacitance-voltage (C-V) is characterized at 300 to 500K. The experimental flat-band voltage ($V_{FB}$) shift was positive. Near-interface trapped charge density and oxide trapped charge density values of Ni/CNT/$SiO_2$ structure were less than values of reference samples. With increasing temperature, the flat-band voltage was negative. It has been found that its oxide quality is related to charge carriers or defect states in the interface of 4H-SiC MIS capacitors. Gate characteristics of 4H-SiC MIS capacitors can be controlled by carbon nanotubes between Ni and $SiO_2$.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.447-455
• /
• 2014

In this research, n-based 4H-MOS Capacitor was fabricated with PECVD (plasma enhanced chemical vapor deposition) process for improving SiC/$SiO_2$ interface properties known as main problem of 4H-SiC MOSFET. To overcome the problems of dry oxidation process such as lower growth rate, high interface trap density and low critical electric field of $SiO_2$, PECVD and NO annealing processes are used to MOS Capacitor fabrication. After fabrication, MOS Capacitor's interface properties were measured and evaluated by hi-lo C-V measure, I-V measure and SIMS. As a result of comparing the interface properties with the dry oxidation case, improved interface and oxide properties such as 20% reduced flatband voltage shift, 25% reduced effective oxide charge density, increased oxide breakdown field of 8MV/cm and best effective barrier height of 1.57eV, 69.05% reduced interface trap density in the range of 0.375~0.495eV under the conduction band are observed.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1355-1357
• /
• 1998

TFT의 게이트 절연막으로 사용되는 절연체는 우수한 절연특성과 낮은 계면포획전하밀도($D_{it}$)를 요구한다. 이에 본 연구에서는 우수한 절연특성을 가지며, 격자상수가 Si과 유사한 $CaF_2$의 증착 특성을 연구하였다. 진공증착법을 이용하여 p형 Si(100) 기판위에 $CaF_2$의 기판온도, 두께를 변화시켜 전기적, 구조적 특성을 평가하였다. 또한 Si 기판에 방향에 따른 박막의 특성을 조사하였다. 구조적 특성분석으로부터 Si(100) 기판의 경우 $CaF_2$는 (200)방향으로 주도적인 성장을 하였으며 기판온도를 상승시킴에 따라 (220)방향으로도 성장을 하는 것으로 나타났다. 열처리 전후의 구조적 특성은 SEM을 통해서 확인 할 수 있었다. 열처리 전후의 특성 변화로부터 저온($100^{\circ}C$이하)에서는 기판과의 성장방향과 동일하였으며 고온($200^{\circ}C$이상)에서는 기판방향과는 다른 방향 성장 결과를 얻었다. 전기적 특성평가를 위하여 C-V 특성을 평가하였다. C-V 특성으로부터 Si(100) 기판의 온도가 $100^{\circ}C$, $1455\AA$ 두께로 증착한$CaF_2$ 박막의 $D_{it}$는 $1.8{\times}10^{11}cm^{-1}eV^{-1}$로 낮은 값을 가지 고 있었으며 0.1MV/cm에서 누설전류밀도가 $10^{-8}A/cm^2$ 이었다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.83-90
• /
• 1998

The effects of dopant activation anneal on GOI (Gate Oxide Integrity) of MOS capacitor with amorphous silicon gate electrode were investigated. It was found that the amorphous silicon gate electrode was crystallized and the dopant atoms were sufficiently activated by activation anneal. The mechanical stress of gate electrode that reveals large compressive stress in amorphous state, was released with increase of anneal temperature from $700^{\circ}C$ to 90$0^{\circ}C$. The resistivity of gate electrode polycrystalline silicon film is decreased by the increase of anneal temperature. The reliability of thin gate oxide and interface properties between oxide and silicon substrate greatly depends on the activation anneal temperature. The charge trapping characteristics as well as oxide reliability are improved by the anneal of 90$0^{\circ}C$ compare to that of $700^{\circ}C$ or 80$0^{\circ}C$. Especially, the lifetimes of the thin gate oxide estimated by TDDB method is 3$\times$10$^{10}$ for the case of $700^{\circ}C$ anneal, is significantly increased to 2$\times$10$^{12}$ for the case of 90$0^{\circ}C$ anneal. Finally, the interface trap density is reduced with relaxation of mechanical stress of gate electrode.

• Applied Chemistry for Engineering
• /
• v.9 no.7
• /
• pp.990-997
• /
• 1998

In this work, the $SiO_2$ films on the silicon substrate with different orientations were first prepared by the low temperature process using the ECR plasma diffusion as a function of microwave power and oxidation time. Before and after thermal treatment, the surface morphology, Si/O ratio from physicochemical properties, and the electrical properties of the oxide films were also investigated. The oxidation rate increased with microwave power, while surface morphology showed the nonuniform due to etching. The film quality, therefore, was lowered with increasing the defect by etching and the content of positive oxide ions in the oxide films from bulk by higher self-DC bias. The content of positive oxide ions in the oxide films with different Si orientations showed Si(100) < Si(111) < poly Si. The defects in $Si/SiO_2$ interface of $SiO_2$ film could be decreased by annealing, while $Q_{it}$ and $Q_f$ were independent of thermal treatment and the dependent on concentration of reactive oxide ions and self-DC bias of substrate. At microwave power of 300, and 400 W, the high quality $SiO_2$ film that had lower surface roughness and defect in $Si/SiO_2$ interface was obtained. The value of interface trap density, then, was ${\sim}9{\times}10^{10}cm^{-2}eV^{-1}$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.7
• /
• pp.37-43
• /
• 2008

In this paper, the dependence of electrical characteristics of Silicon-$Al_2O_3$-Nitride-Oxide-Silicon (SANOS) memory cell transistors and program/erase (P/E) speed, reliability of memory device on interface trap between Si substrate and tunneling oxide and bulk trap in nitride layer were investigated using charge pumping method which has advantage of simple and versatile technique. We analyzed different SANOS memory devices that were fabricated by the identical processing in a single lot except the deposition method of the charge trapping layer, nitride. In the case of P/E speed, it was shown that P/E speed is slower in the SANOS cell transistors with larger capture cross section and interface trap density by charge blocking effect, which is confirmed by simulation results. However, the data retention characteristics show much less dependence on interface trap. The data retention was deteriorated as increasing P/E cycling number but not coincides with interface trap increasing tendency. This result once again confirmed that interface trap independence on data retention. And the result on different program method shows that HCI program method more degraded by locally trapping. So, we know as a result of experiment that analysis the SANOS Flash memory characteristic using charge pumping method reflect the device performance related to interface and bulk trap.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.239-242
• /
• 1998

Ca $F_2$ films have superior gate insulator properties than conventional gate insulator such as $SiO_2$, Si $N_{x}$, $SiO_{x}$, and T $a_2$ $O_{5}$ to the side of lattice mismatch between Si substrate and interface trap charge density( $D_{it}$). Therefore, this material is enable to apply Thin Film Transistor(TFT) gate insulator. Most of gate oxide film have exhibited problems on high trap charge density, interface state in corporation with O-H bond created by mobile hydrogen and oxygen atom. This paper performed Ca $F_2$ property evaluation as MIM, MIS device fabrication. Ca $F_2$ films were deposited at the various substrate temperature using a thermal evaporation. Ca $F_2$ films was grown as polycrystalline film and showed grain size variation as a function of substrate temperature and RTA post-annealing treatment. C-V, I-V results exhibit almost low $D_{it}$(1.8$\times$10$^{11}$ $cm^{-1}$ /le $V^{-1}$ ) and higher $E_{br}$ (>0.87MV/cm) than reported that formerly. Structural analysis indicate that low $D_{it}$ and high $E_{br}$ were caused by low lattice mismatch(6%) and crystal growth direction. Ca $F_2$ as a gate insulator of TFT are presented in this paper paperaper

• Journal of the Korean Vacuum Society
• /
• v.14 no.2
• /
• pp.91-96
• /
• 2005

The silicon-on-insulator (SOI) wafer fabrication technique has been developed by using ion-cut process, based on proton implantation and wafer bonding techniques. It has been shown by SRIM simulation that 65keV proton implantation is required for a SOI wafer (200nm SOI, 400nm BOX) fabrication. In order to investigate the optimum proton dose and primary annealing condition for wafer splitting, the surface morphologic change has been observed such as blistering and flaking. As a result, effective dose is found to be in the $6\~9\times10^{16}\;H^+/cm^2$ range, and the annealing at $550^{\circ}C$ for 30 minutes is expected to be optimum for wafer splitting. Direct wafer bonding is performed by joining two wafers together after creating hydrophilic surfaces by a modified RCA cleaning, and IR inspection is followed to ensure a void free bonding. The wafer splitting was accomplished by annealing at the predetermined optimum condition, and high temperature annealing was then performed at $1,100^{\circ}C$ for 60 minutes to stabilize the bonding interface. TEM observation revealed no detectable defect at the SOI structure, and the interface trap charge density at the upper interface of the BOX was measured to be low enough to keep 'thermal' quality.