• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.5
• /
• pp.556-561
• /
• 1995

Persisent circadian rhythms in carbon assimilation, stomatal conductance and soluble carbohydrate concentration were investigated during grain filling period in rice plant transferred from a natural photoperiod to constant conditions. A weak rhythm in photosynthesis, measured as carbon assimilation, and stomatal opening, as conductance to water vapor, with a period of approximately 24-hours, occurred under constant condition. Carbon assimilation and stomatal conductance reached maximum values near noon and minimum values near midnight during the early stage (until 72-hour) after transferring to constant condition, and then the amplitude and phase were changed slowly, the rhythms with little damping, reaching maximum values near midnight and minimum values near noon during 96~120-hours after transferring. However, photosynthesis in plants grown for 14days after anthesis under constant moderate light(day and night) did not oscillated in constant condition unlike plants grown under a cycle of light and darkness. These phenomenon was observed in soluble carbohydrate concentration in flag leaves as well. Evidences from several approaches indicate that endogenous rhythms of $CO_2$ assimilation, stomatal conductance and soluble carbohydrate concentration are closely couped with each other and particularly important to plants, which depend on the natural day-night cycle as a external signal.

• Journal of Adhesion and Interface
• /
• v.12 no.4
• /
• pp.111-116
• /
• 2011

The characteristics of natural resin, sap of the lacquer tree were examined as an adhesive for the ceramic conservation since it has such outstanding properties like corrosion resistance against acid and alkali, heat-resistance, waterproof, antiseptic and protection against insects. In order to utilize raw lacquer as an adhesive not under the hardening conditions of lacquer like high humidity (RH 75 to 85%) and high temperature (120 to $170^{\circ}C$), but under normal condition, isinglass and animal glue were added to raw lacquer at certain ratio. In addition, the viscosity and the drying time were measured and their possibilities of application were also investigated through measurement of tensile and adhesive strength. As a result of experiment, it was possible to dry at room temperature and RH $50{\pm}5%$ to mix with raw lacquer and glue, and the drying time of sample with animal glue was faster than that of isinglass. Furthermore, the adhesion of sample with glue was increased more than raw lacquer. It seems to be possible to use the environmental friendly traditional adhesive for the ceramic conservation and restoration, if there are studies or examinations of safety of applications on objects and weathering resistance.

• Journal of Periodontal and Implant Science
• /
• v.35 no.3
• /
• pp.549-561
• /
• 2005

이 연구의 목적은 새로이 제작된 chitosan-poly(L-lactic acid)(PLLA) 다층 다공성 차폐막의 생체적합성 및 골세포활성도 및 골재생능을 평가하는 것이다. 제작된 차폐막을 24 well에 넣고 clonal osteoblast-like cell line(MC3T3-E1)을 접종한 군을 실험군으로, 차폐막을 사용하지 않은 대조군으로 하였다. 배양 1일, 7일 및 14일째에 각 well에서 세포수를 측정하였다. 주사전자현미경을 이용하여 차폐막에 부착된 세포의 형태관찰을 시행하였다. RNA 추출 및 RT-PCR을 실시한 후, agarose gel상에서 전기영동하여 조골세포 표식자인 collagen type I(COL), osteopontin(OP) 및 osteocalcin(OC) mRNA의 발현을 관찰하였다. 제작된 매트릭스의 생체적합성 및 골재생능을 관찰하기 위하여 백서의 두개골에 직경 8mm의 원형 결손부를 형성한 후 차폐막을 이식한 군을 실험군으로, 아무 것도 넣지 않은 군을 대조군으로 하여 4주 경과 후 실험동물을 희생시킨 후 조직학적관찰을 시행하였다. 시간경과에 따른 부착세포수 관찰결과, 배양 14일까지 조골세포의 수가 지속적으로 증가하였고, 주사전자현미경으로 세포의 형태 관찰결과, 배양된 세포들은 중층의 형태로 성장하면서 시간경과에 따라 세포가 응집되는 양상을 나타내었다. 관찰 기간동안 COL, OP, 및 OC mRNA의 발현이 관찰되어 배양 전 기간동안 조골세포의 형질이 잘 유지되고 있음을 알 수 있었다. 백서 두개골 결손부에 이식된 차폐막은 염증반응 없이 주위 조직과 우수한 생체적합성을 나타내었으며, 차폐막을 이식하지 하지 않은 대조군에 비해 높은 신생골 형성을 나타내었다. 이상의 관찰결과로 새로이 제작된 chitosan-PLLA 차폐막은 우수한 생체적합성 및 골재생능을 나타냄을 알 수 있었으며, 향후 이를 골조직 재생 및 치주조직유도재생 분야에 응용될 수 있을 것으로 생각된다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.4
• /
• pp.44-50
• /
• 2016

A study to apply phase change material(PCM) to rapid hardening cement paste forming semi-rigid pavement was carried out. The characteristics fresh and hardened paste were evaluated through the experiment for a total of 6 mixtures according to the cement type and the substitution of phase change material for acrylate. The fluidity by substituting phase change material for acrylate satisfied the target flow time of 10 to 13 seconds. In case of setting time, it was possible to secure the performance of rapid hardening cement by substituting phase change material, and if the substitution ratio over 60%, the initial set occurred 1 to 2 minutes faster than other mixtures. In case of compressive strength and bond strength, it showed similar strength characteristics with the plain mixture, and it satisfied both the target compressive and bonding strength of 36MPa and 2MPa. The mixture substituting phase change material showed higher resistance to chloride ion penetration than the mixture only using acrylate and the OPC level was insufficient. From the results of physical and mechanical performances of semi-rigid pavement cement paste, the phase change material substitution rate of 20% was effective in the range of this study.

• Restorative Dentistry and Endodontics
• /
• v.34 no.3
• /
• pp.208-214
• /
• 2009

The purpose of this study was to compare the dye leakage of MTA (mineral trioxide aggregate) apical plug produced by two orthograde placement techniques (hand condensation technique and ultrasonically assisted hand condensation technique). To simulate straight canal, 60 transparent acrylic blocks with straight canal were fabricated. These transparent acrylic blocks were divided into 2 groups (Group C; hand condensation technique (HC) and Group U; ultrasonically assisted hand condensation technique (UAHC)) of 30 blocks with each MTA application method. Each group was divided into 2 subgroups (n=15) with different canal size of #70 (subgroup C70 and subgroup U70) and #120 (subgroup C120 and subgroup U120). After apical plug was created, a wet paper point was placed over the MTA plug and specimen was kept in a humid condition at room temperature to allow MTA to set. After 24 hours, remaining canal space was backfilled using Obtura II. All specimens were transferred to floral form socked by 0.2% rhodamine B solution and stored in 100% humidity at room temperature. After 48 hours, resin block specimens were washed and scanned using a scanner. The maximum length of micro leakage was measured from the scanned images of four surfaces of each resin block using Photoshop 6.0. Statistical analysis was performed with Mann-Whitney U test. Group U of UAHC had significantly lower leakage than Group C of HC in #70-size canal (subgroup U70) (p<0.05).

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.11a
• /
• pp.72-72
• /
• 1998

원자력발전소 1차계통내 밸브의 경면처리(hardfa따1잉에 사용되는 재료는 $90~343^{\circ}C$의 고온과 높은 접촉응력 그리고 급격한 압력변화가 일어나는 환경에서 사용되기 때문에 내마모성과 내식성 그리고 cavitation erosion 저항성이 우수한 Co계 Stellite 합금이 현재 사용되어진다. 그러나 Co가 원력발전소 1차계통의 방사선장을 형성하는 주요 원소로 알려지면서 S Stellite 합금을 대체할 수 있는 Fe계 경면처리용 합금을 개발하려는 연구가 진행되고 있다. 현재 Fe계 경면처리용 합금의 개발은 적절환 팝금원소를 첨가하여 적충결함에너지를 낮춤 으로써 전위의 교차슬립을 억제하여 표면을 경화시키고, 소성변형을 억제하여 마모저항성을 향상시키려는 방법으로 연구가 진행되고 있다. 본 연구에서는 Fe-Cr-Ni-Si-C 합금에 Fe계 합금의 적충결함에너지를 감소시키는 것으로 알려진 vanadium을 0, 1, 2wt%첨가하여 첨가량의 변화가 cavitation erosion 저항성에 미치 는 영향을 조사하였다. Cavitation erosion 실험은 초음파를 이용하여 미세한 기포를 발생시키는 vibratory type으로 A ASTM G-32 규격에 따라 제작된 실험장치를 이용하여 $25{\pm}2^{\circ}C$의 온도의 증류수 속에 잠긴 상태에서 실시하였다. 시면은 지름 16mm, 두게 7mm의 버턴형태로 vanadium 첨가량을 변화시킨 조성을 아크 용융 방법을 이용하여 제작하였으며 hom끝단부에 부착하여 cavitation e erosion 저항성 살험을 하였다. 시편의 cavitation erosion 실험시간에 따른 무게감소량을 측 정하였으며 cavitation erosion 시킨 시편의 표면을 SEM으로 관찰하였다.겨지는 열전달 매체액 과 신규 부식억제제가 적용된 시스템 등 객관적으로 확인된 부식억제제 시스랩에 대 하여 다양한 평가 방법을 동원 비교분석하고자 하였다. 실험은 KSM 2142에 의한 무게감량법, 분극곡선 측정에 의한 $E_P$(공식개시전위), $E_R$(재부동태화전위) 측정, 시간에 따른 자연전위 변화 측정 빛 이때의 부식속도(선형분극법), 인위적인 피막 파괴 전,후 의 전위 변화 및 부식속도 측정법에 의한 국부부식 발달 저지능 등을 평가하여 각 실험결과를 비교분석하여 보았다. 수록 민감하여 304 의 IGSCC 와 매우 유사한 거동을 보인다. 본 강연에서는 304 와 600 의 고온 물에서 일어나는 IGSCC 민감도에 미치는 환경, 예민화처리, 합금원소의 영향을 고찰하고 이에 대한 최근의 연구 동향과 방식 방법을 다룬다.다.의 목적과 지식)보다 미학적 경험에 주는 영향이 큰 것으로 나타났으며, 모든 사람들에게 비슷한 미학적 경험을 발생시키는 것 이 밝혀졌다. 다시 말하면 모든 사람들은 그들의 문화적인 국적과 사회적 인 직업의 차이, 목적의 차이, 또한 환경의 의미의 차이에 상관없이 아름다 운 경관(High-beauty landscape)을 주거지나 나들이 장소로서 선호했으며, 아름답다고 평가했다. 반면에, 사람들이 갖고 있는 문화의 차이, 직업의 차 이, 목적의 차이, 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$의 범위를 벗어나지 않는다. 그렇기 때문에도 $\ulcorner$

• Korean Journal of Food Science and Technology
• /
• v.32 no.2
• /
• pp.387-395
• /
• 2000

The rheological properties of wheat flour dough and qualities of bread prepared with 0, 10, and 20% of dietary fiber slurry extracted and purified from ascidian (Halocynthia roretzi) tunic were investigated. Water absorption of the dough increased with the increase of dietary fiber slurry. Both arrival and development time of the dough with 10 and 20% dietary fiber slurry added were shorter than those of the control. An increase in the added amount of the dietary fiber slurry resulted in an increase of weakness. The dough's extensibility and resistance to extension were decreased, and the ratio of resistance to extensibility (R/E) decreased with the increase in the dietary fiber slurry. The maximum viscosity gradually decreased with the increase in the amount of dietary fiber slurry, while the temperature of gelatinization was not changed. Both loaf and specific volume of bread were slightly decreased with an increase in the amount of dietary fiber slurry. Overall preference scores by sensory evaluation and the quality characteristics of the bread with up to 20% dietary fiber slurry added was not significantly different from those of the control(p<0.05). The results indicated that the addition of the dietary fiber from ascidian tunic retarded staling and improved the shelf-life of the bread by enhancing the water holding capacity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.499-508
• /
• 2016

Injection molding is a method for manufacturing many products, wherein a plasticized resin is injected into a mold at high pressure and hardened. According to the method, the product can be manufactured into various forms, and the mass production of up to tens of thousands of products is possible. The purpose of this study was to determine the process conditions for manufacturing a door latch for automobiles, through an analysis of the injection molding method. To calculate an appropriate injection flow for injection molding, a primary analysis for comparing the injection time, pressure, flow pattern, consolidation range, shear stress, shear rate, and weld line, as well as a secondary analysis for determining the conditions for stabilizing the molding temperature, holding pressure, and cooling process, were conducted. The characteristics of injection molding, and their influence on the product quality are discussed. No weld line and pores were observed on the products that had been manufactured based on the process conditions determined above. In addition, there were no flaws regarding the deformation compared to the prototype. Therefore, the manufacture of a product under the conditions determined in this study can reduce the defect rate compared to the existing production, and the process is also more competitive due to reduced production time.

• Journal of Korean Society of Forest Science
• /
• v.12 no.1
• /
• pp.23-29
• /
• 1971

In order to see a possible strengthening of much injection of synthetic resin into timber by way of electric osmosis, Authors examined the change of the bending strength of the sample timber piece after being injected. 1. Three kinds of sample tree species, Pinus rigida, Magnolia and Populus were used and the size of the sample timber pieces was $30mm{\times}30mm{\times}330mm$. 2. Each of the electric osmosis was made with 250V of D. C. voltage and $0.01A/cm^2$ of the current for 2 hours and the experimenter hardened the injected resin by putting the sample in an oven of $120^{\circ}{\pm}2^{\circ}C$ temperature for 24 hours. 3. The size of the test sample piece for bending strength measurement was $20mm{\times}20mm{\times}320mm$ and Amsler type universal timber test machine was used for the measurement. 4. The strength difference between treated and untreated samples was as follows. Pinus rigida high sig. Magnolia None Sig. Populus Sig.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.4
• /
• pp.450-456
• /
• 2022

In this study, as the preliminary research on the development of heating concrete members, compressive strength and accelerated chloride diffusion behavior in the mortar specimens containing C₁₂A₇ based binder and anhydrite was evaluated. Also, the effect of the mixing ratio of the citric acid based retarder was quantitatively evaluated by considering 4 levels of mixing cases. The compressive strength tests of the mortar specimen were performed referred to KS L ISO 679, and the accelerated chloride diffusion tests were performed according to NT BUILD 492 and ASTM C 1202. In the mortar with 0.3 % of retarder, the highest compressive strength was evaluated, which showed the strength development ratio of 127.6 % compared to the control case. It was considered that engineering performance was improved by effectively securing setting and curing time with 0.3 % of citric acid based retarder. As the result of the evaluation of the passed charge and the accelerated chloride diffusion coefficient, the evaluation results had similar behavior with the results of compressive strength. According to the previous study, the strength behavior and the chloride diffusion behavior had a linear relationship. The mixture showing the highest strength performance had the highest durability performance for chloride ingress, and the heating concrete development from this study will be performed in the future.