• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.285-298
• /
• 2003

Shear properies of geosynthetic/geosynthetic and geosynthetic/soil interfaces which are widely met in landfill sites were evaluated from the inclined board tests. The inclined board testing apparatus is known to reproduce the shear behavior on the low normal stress most accurately. In this study, the friction angle of each interface was estimated and the tensile force mobilized at the geosynthetic was measured as well. The test results showed that the friction angle of each interface and the tensile force of the geosynthetics depended on the amount of normal stress, the type of the geosynthetics used, and the combinations of geosynthetics and soils. In addition, the sand/geotextile/geomembrane interface system was simulated in this study, and it was observed that the tensile force developed at the geomembrane decreased due to the protection effect of the geotextile located above the geomembrane. The test results of this research was compared with those of direct shear tests published, too. Finally, by comparing the measured tensile force of the geosynthetics when the initial displacement of the box occurs, when the slope is called as the critical slope, with suggested analytic solution, the accuracy of analytic solution and the applicability to design were identified.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2C
• /
• pp.73-80
• /
• 2006

The shear behavior of four different interfaces consisting of four types of geosynthetics was investigated, and both static and dynamic test for the geosynthetic interfaces were conducted. The monotonic shear experiments were performed by using an inclined board apparatus and large direct shear device. The interface shear strength obtained from the inclined board test was compared with calculated values from large direct shear tests. The comparison results indicated that direct shear tests show high possibility to over-predict the shear strength in the low normal stress range where direct shear tests are not performed. Curved failure envelopes were also obtained for interface cases where two static shear tests were conducted. By comparing the friction angles measured from three tests, i.e. direct shear, inclined board, and shaking table test, it was found that the friction angle might be different depending on the test method and normal stresses applied in the research. Therefore, it was concluded that the testing method should be determined carefully by considering the type of loads and the normal stress expected in the field with using the geosynthetic materials installed in the site.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.255-255
• /
• 2021

내수 침수는 강물과 같은 외수보다는 제내지에서 하수 또는 우수의 배제가 불량하여 발생되는 범람이다. 내수 침수 상황에서 침수심의 정확한 관측과 예보된 강수로부터 침수심을 예측할 수 있는 시스템 즉, 스마트 목자판이 개발되고 있다. 시스템 운용에 사용될 소프트웨어 가운데 하나로서 침수 해석을 위한 수치 모형이 필요하다. 내수에 의한 침수와 그것의 배제를 무리 없이 모의하려면, 물이 차고 빠지는 물리 현상을 타당하게 해석하는 것이 관건일 것이다. 그에 따라 2차원 천수 방정식을 유한 체적법으로 해석할 때 흐름률(flux) 계산에 근사 Riemann 해법을 적용하는 모형을 도입하였다. 단순하면서도 내수 침수의 재현에서 드러날 수 있는 취약점들을 포괄할 수 있도록 경사면과 계단으로 가상 지형을 구성하였으며, 강수로 인한 지형의 침수에 대해 개발된 모형을 시험하였다. 근사 Riemann 해법은 흐름률의 정확한 평가로 잠김과 드러남 모의가 자연스런 장점이 있으나, 해석 방법이 복잡하여 계산 시간이 비교적 오래 걸리므로 그에 대한 대책이 요구된다.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.1
• /
• pp.42-50
• /
• 2013

Since 1990's, a plywood for flooring base has gotten customers' demand. Costs of raw material and production increased because of changed environment of industry. Tropical timber such as Red Meranti (Shorea acuminate) used for raw material of the floor has been depleting beside countries in South Eastern Asia changed species of afforestation. As a result, it gets hard to secure good quality of raw material for plywood. Moreover plywood price is increased suddenly after earthquake in Japan. Eucalyptus (Eucalyptus globulus) in china has been using for raw material as a countermeasure of changed environment of industry. In this study, possibility of using flooring consisted of Eucalyptus veneer as crossband layers was checked by deflection experiments. Flooring consisted of Red Meranti was used for comparison. Two factors which impact on deflection are a type of density gradient and density difference between Long-grain veneer and Short-grain veneer. Red Meranti samples are M type of density gradient on the other hand Eucalyptus samples are W type of density gradient. The more samples have high density difference, the more deformation was checked. A sample which has big density difference between core and cross bands layer warp more also deform. Flooring was deformed smaller than plywood and samples which have big density difference was deformed more.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.221-229
• /
• 2001

연약지반의 측방유동으로 인한 피해가 예상되는 국내 현장에 성토지지말뚝공법을 적용하기 위한 연구의 일환으로 실제 현장에서 성토지지말뚝이 발휘하는 효과를 규명하기 위한 현장시험이 계획되었다. 본 현장시험은 직경 40.64cm의 강관말뚝을 3본씩 총 4여로 시공하고, 각 열의 줄말뚝은 콘크리트캡보로 연결한 다음 총 8m까지 성토하였다. 현장시험은 총 2회에 걸쳐 수행하였으며, 성토지지말뚝의 하중분담효과를 확인하기 위해 하중계, 토압계, 지중경사계, 그리고 침하판을 이용한 계측을 실시하였다. 또한 계측결과를 제안이론식과 비교분석하였다. 이러한 연구 결과 성토지지말뚝을 시공할 경우 성토지지말뚝 위 성토지반속에 발달하는 지반아치에 의해 대부분의 성토하중이 말뚝으로 전이됨을 확인하였고, 말뚝캡보의 설치 간격이 좁을수록, 그리고 성토고가 높을수록 성토지지말뚝의 하중분담효과가 더 커지게 됨을 확인할 수 있었다. 또한 설계시 성토지지말뚝의 설치범위를 합리적으로 결정하기 위해서는 성토지지말뚝이 성토사면의 사면안정효과에 미치는 영향을 고려해야 함을 알 수 있었으며, 제안이론식이 현장상태의 성토지지말뚝에 합리적으로 적용될 수 있음을 입증하였다.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.3
• /
• pp.17-25
• /
• 1990

양표면은 무결점재를, 가운데 단판은 경사목리 및 목리방향의 할열을 가진 단판을 사용하여 제조한 3매 단판 적충재에 있어서 목리방향과 할열의 인장탄성계수 및 인장강도에 미치는 영향에 대하여 조사하였다. 또한, 비파괴 시험 방법인 응력파 실험에 의하여 각단판의 탄성계수를 측정하고, 이들 단판의 탄성계수로부터 단판적층재의 탄성계수를 예측하여 실측치와 비교하였다. 응력파에 의해 예측된 탄성계수는 인장실험으로부터 얻어진 결과와 거의 일치하였으며 인장탄성계수와 인장강도간에도 높은 상관관계를 나타내었다($r^2$=0.681). 인장강도에 있어서는 가운데 단판 할열의 영향은 나타나지 않았으나 목리의 경우 경사각이 증가함에 따라 인장강도가 감소하는 경향을 나타내었다.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.2
• /
• pp.22-27
• /
• 1982

This experiment was carried out to evaluate the results of fire retardancy of sealer coated plywood by Building material combustibility tester and Inclined panel tester. At this study, weight loss percentage, flame exhausted time, burning point and smoke yield coefficient were examined. The findings of this study lead to conclusions as listed below. 1. It was obvious that weight loss percentage and flame exhausted time of Inclined panel tester had more remarkable tendency than those of Building material combustibility tester. 2. Burning point was determined by Inclined panel tester while smoke yield coefficient by Building material combustibility tester. 3. Weight loss percentage decreased remarkably with proportion to the increase of sealer coated amount during 5 minutes burning. 4. Flame exhausted time decreased with proportion to the increase of sealer coated amount during 3 minutes burning. 5. Burning point indicated increasing tendency with proportion to the increase of sealer coated amount. 6. Smoke yield coefficient of urea scaler showed definite inclination decreasing with the increase of sealer coated amount.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.10
• /
• pp.934-939
• /
• 2007

Thrust vector control(TVC) is the method which generates the side force and moment by controlling the exhausting gas directly from the supersonic nozzle to change the trajectory of a missile quickly. In this paper, performance study on the tapered ramp tabs asymmetrically installed in the supersonic nozzle exhaust for the thurst vector control has been carried out using the supersonic cold flow system. To study the shock wave structure and location of the oblique shock wave produced by the ramp tab, the flow field visualization using the schlieren system is conducted. This paper provides the thrust spoilage, three directional forces and moments and distribution of surface pressure on the region enclosed by the tapered ramp tabs.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.3
• /
• pp.161-175
• /
• 1985

The simplified method drawing the S-N curves in welding joints of the cover plates, the transverse stiffners and the gusset plates of the plate girders by calculation and its computer program without the direct fatigue tests, was established. And the method was applied to the Young- Dong Great Bridge, the 3 th Han River Bridge and the Kang Chon Bridge. Before this, SS 41, SS 50, SWS 50 and SWS 58 were selected, then the compact tension specimens were made by the use of these materials, the things welded by these materials transversely and the ones longitudinally to the crack propagation direction. The fatigue tests were performed by the use of these 'specimens, and the values of material constants c and m were obtained. By these results the followings were obtained. It was showed that the fatigue: strength in the case of the cover plates was much lower than in the case of other two cases. It was showed that, in the case of the cover plates with the cover plates thicker the fatigue strength was lower, but besides this the fatigue strength was not much influenced by the size of specimens. It was showed that in the difference from this the fatigue strength was sensitively influenced by the values of c and m. It was showed that in accordance with the lower values of c and m the fatigue strength was fairly higher, in accordance with the lower values of m the gradient of the S-N curves was abrupter. It was considered that if such data were accumulated continuously, in the near future the basic pattern used availably in providing the indicater of the fatigue design of the plate girders, and presuming the life-proof of the existing plate girders.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.4
• /
• pp.344-350
• /
• 2009

This paper proposes a hybrid antenna with novel beam steering scheme. The antenna have a cassegrain structure composed of two reflectors. The main reflector is designed for high gain performance using parabola curvature, and the sub-reflector is plate and can be rotated by ${\pm}3^{\circ}$. Thus proposed antenna can steer a antenna beam using the inclination of sub-reflector. A feed array composed of 20 elements is adapted as a feeder for electrical beam steering, and the antenna can be possible to steer the beam by the feed array with sub-reflector. Proposed antenna was fabricated to be operated in Ka-band(30.085$\sim$30.885 GHz) for TX and K-band(20.355$\sim$21.155 GHz), which are the operation frequencies of the Korean satellite, Mugunhwa, to provide satellite multi-media service to vehicles. By the performance test, it can be known that the antenna has minimum gain of 47 dBi for TX and 44.4 dBi for TX and can steer the beam by ${\pm}2^{\circ}$ with sub-reflector.