• Korean Journal of Optics and Photonics
• /
• v.34 no.6
• /
• pp.241-247
• /
• 2023

We examine the spectral characteristics of laser-induced periodic surface structures (LIPSSs) formed on an amorphous silicon film irradiated by a 355-nm nanosecond laser. A Gaussian beam with a diameter of 196 ㎛ is used to perform a two-dimensional raster scan. The laser's pulse number is varied from 190 to 280, and its intensity is adjusted within 100-130 mJ/cm². LIPSSs with a periodicity of approximately 330 nm form on the surface of the Si film, aligned perpendicular to the laser's polarization. Transmission spectra of the samples show dips around 700 nm for transverse electric polarization and around 500 nm for transverse magnetic polarization. The features are investigated with a one-dimensional-grating model using a rigorous coupled-wave analysis. Simulations confirm that the observed dips are due to the resonant modes, depending on the polarization.

• Applied Chemistry for Engineering
• /
• v.25 no.5
• /
• pp.455-462
• /
• 2014

This work investigated the hydrophobic coating of silicate yellow phosphor powder in the form of divalent europium-activated strontium orthosilicate ($Sr_2SiO_4:Eu^{2+}$) by using an atmospheric pressure dielectric barrier discharge (DBD) plasma with argon as a carrier and hexamethyldisiloxane (HMDSO), toluene and n-hexane as precursors. After the plasma treatment of the phosphor powder, the lattice structure of orthosilicate was not altered, as confirmed by an X-ray diffractometer. The coated phosphor powder was characterized by scanning electron microscopy, fluorescence spectrophotometry and contact angle analysis (CAA). The CAA of the phosphor powder coated with the HMDSO precursor revealed that the water contact angle increased from $21.3^{\circ}$ to $139.5^{\circ}$ (max. $148.7^{\circ}$) and the glycerol contact angle from $55^{\circ}$ to $143.5^{\circ}$ (max. $145.3^{\circ}$) as a result of the hydrophobic coating, which indicated that hydrophobic layers were successfully formed on the phosphor powder surfaces. Further surface characterizations were performed by Fourier transform infrared spectroscopy and X-ray photoelectron spectrometry, which also evidenced the formation of hydrophobic coating layers. The phosphor coated with HMDSO exhibited a photoluminescence (PL) enhancement, but the use of toluene or n-hexane somewhat decreased the PL intensity. The results of this work suggest that the DBD plasma may be a viable method for the preparation of hydrophobic coating layer on phosphor powder.

• Korean Journal of Remote Sensing
• /
• v.14 no.1
• /
• pp.53-68
• /
• 1998

Observation of hydrometeors' behavior in the atmosphere is important to understand weather and climate. By conventional observations, we can get the distribution of water vapor at limited number of points on the earth. In this study, the precipitable water has been estimated from the split window channel data on GMS-5 based upon the technique developed by Chesters et al.(1983). To retrieve the precipitable water, water vapor absorption parameter depending on filter function of sensor has been derived using the regression analysis between the split window channel data and the radiosonde data observed at Osan, Pohang, Kwangiu and Cheju staions for 4 months. The air temperature of 700 hPa from the Global Spectral Model of Korea Meteorological Administration (GSM/KMA) has been used as mean air temperature for single layer radiation model. The retrieved precipitable water for the period from August 1996 through December 1996 are compared to radiosonde data. It is shown that the root mean square differences between radiosonde observations and the GMS-5 retrievals range from 0.65 g/$cm^2$ to 1.09 g/$cm^2$ with correlation coefficient of 0.46 on hourly basis. The monthly distribution of precipitable water from GMS-5 shows almost good representation in large scale. Precipitable water is produced 4 times a day at Korea Meteorological Administration in the form of grid point data with 0.5 degree lat./lon. resolution. The data can be used in the objective analysis for numerical weather prediction and to increase the accuracy of humidity analysis especially under clear sky condition. And also, the data is a useful complement to existing data set for climatological research. But it is necessary to get higher correlation between radiosonde observations and the GMS-5 retrievals for operational applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.3 no.1
• /
• pp.26-27
• /
• 1978

It can be expected that intelligence and knowledge will be the core of the post-industrial society in a near future. Accordingly, the age of intelligence shall be accelerated extensively to find ourselves in an age of 'Communication' service enterprise. The communication actions will increase its efficiency and multiply its utility, indebted to its scientic principles and legal idea. The two basic elements of communication action, that is, communication station and communication men are considered to perform their function when they are properly supported and managed by the government administration. Since the communication action itself is composed of various factors, the elements such as communication stations and officials must be cultivated and managed by specialist or experts with continuous and extensive study practices concerned. With the above mind, this study reviewed our public service officials law with a view to improve it by providing some suggestions for communication experts and researchers to find suitable positions in the framework of government administration. In this study, I would like to suggest 'Occupational Group of Communication' that is consisted of a series of comm, management positions and research positions in parallel to the existing series of comm, technical position. The communication specialist or expert is required to be qualified with necessary scientific knowledge and techniques of communication, as well as prerequisites as government service officials. Communication experts must succeed in the first hand to obtain government licence concerned in with the government law and regulation, and international custom before they can be appointed to the official positions. This system of licence-prior-to-appointment is principally applied in the communication management position. And communication research positions are for those who shall engage themselves to the work of study and research in the field of both management and technical nature. It is hopefully expected that efficient and extensive management of communication activities, as well as scientific and continuous study over than communication enterprise will be upgraded at national dimensions.

• Korean Chemical Engineering Research
• /
• v.50 no.4
• /
• pp.666-671
• /
• 2012

Gas hydrates are inclusion compounds formed when small-sized guest molecules are incorporated into the well defined cages made up of hydrogen bonded water molecules. Since large masses of natural gas hydrates exist in permafrost regions or beneath deep oceans, these naturally occurring gas hydrates in the earth containing mostly $CH_4$ are regarded as future energy resources. The heat of dissociation is one of the most important thermal properties in exploiting natural gas hydrates. The accurate and direct method to measure the dissociation enthalpies of gas hydrates is to use a calorimeter. In this study, the high pressure micro DSC (Differential Scanning Calorimeter) was used to measure the dissociation enthalpies of methane, ethane, and propane hydrates. The accuracy and repeatability of the data obtained from the DSC was confirmed by measuring the dissociation enthalpy of ice. The dissociation enthalpies of methane, ethane, and propane hydrates were found to be 54.2, 73.8, and 127.7 kJ/mol-gas, respectively. For each gas hydrate, at given pressures the dissociation temperatures which were obtained in the process of enthalpy measurement were compared with three-phase (hydrate (H) - liquid water (Lw) - vapor (V)) equilibrium data in the literature and found to be in good agreement with literature values.

• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.629-635
• /
• 2001

To improve the ductility of $A1_3Hf$ intermetallics, which are the potential high temperature structural materials, the mechanical alloying behavior. the effect of Cu addition on the $Ll_2$ phase formation and the behavior of vacuum hot-pressed consolidation were investigated. During the mechanical alloying by SPEX mill, the $Ll_2 A1_3Hf$ intermetallics with the grain size of 7~8nm was formed after 6 hours of milling in Al-25at.%Hf system. The $Ll_2$ Phase of Al_3Hf$ intermetallics with the addition of 12.5at.%Cu, similar to that of the binary Al-25at.% Hf, was formed, but the milling time necessary for the formationof the $Ll_2$ phase was delayed form 6 hours to 10 hours. The lattice parameter of ternary $Ll_2(Al+Cu)_3Hf$ intermetallics decreased with the increase of Cu content. The onset temperature of $Ll_2$ to $D0_{23}$ phase in $Al_3Hf$ intermetallics was around 38$0^{\circ}C$, the temperature upon completion varied from 48$0^{\circ}C$ to 5$50^{\circ}C$ as the annealing time. The onset temperature of $Ll_2$ to $D0_{23}$ phase transformation in $(Al+ Cu)_3Hf$ intermetallics increased with the amount of Cu and the highest onset temperature of $700^{\circ}C$ was achieved by the Cu addition of 10at.%. The relative density increased from 89% to 90% with the Cu addition of 10at.% in $Al_3Hf$ intermetallics hot-pressed in vacuum under 750MPa at 40$0^{\circ}C$ for 3 hours. The relative density of 92.5% was achieved without the phase transformation and the grain growth as the consolidation temperature increased from 40$0^{\circ}C$ to 50$0^{\circ}C$ in $(Al+Cu)_3Hf$ intermetallics hot-pressed in vacuum under 750MPa for 3 hours.

• Progress in Medical Physics
• /
• v.16 no.1
• /
• pp.24-31
• /
• 2005

The stereotactic radiosurgery (SRS) describes a method of delivering a high dose of radiation to a small tar-get volume in the brain, generally in a single fraction, while the dose delivered to the surrounding normal tissue should be minimized. To perform automatic plan of the SRS, a new method of multi-isocenter/shot linear accelerator (linac) and gamma knife (GK) radiosurgery treatment plan was developed, based on a physical lattice structure in target. The optimal radiosurgical plan had been constructed by many beam parameters in a linear accelerator or gamma knife-based radiation therapy. In this work, an isocenter/shot was modeled as a sphere, which is equal to the circular collimator/helmet hole size because the dimension of the 50% isodose level in the dose profile is similar to its size. In a computer-aided system, it accomplished first an automatic arrangement of multi-isocenter/shot considering two parameters such as positions and collimator/helmet sizes for each isocenter/shot. Simultaneously, an irregularly shaped target was approximated by cubic structures through computation of voxel units. The treatment planning method by the technique was evaluated as a dose distribution by dose volume histograms, dose conformity, and dose homogeneity to targets. For irregularly shaped targets, the new method performed optimal multi-isocenter packing, and it only took a few seconds in a computer-aided system. The targets were included in a more than 50% isodose curve. The dose conformity was ordinarily acceptable levels and the dose homogeneity was always less than 2.0, satisfying for various targets referred to Radiation Therapy Oncology Group (RTOG) SRS criteria. In conclusion, this approach by physical lattice structure could be a useful radiosurgical plan without restrictions in the various tumor shapes and the different modality techniques such as linac and GK for SRS.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.310-310
• /
• 2014

ZnO박막은 넓은 밴드갭 (3.37 eV), 높은 여기 결합 에너지 (60 meV)를 가지는 육방정계 우르자이트(hexagonal wurtzite) 결정구조를 가지는 II-VI족 화합물 반도체로, 가시광선 영역에서의 높은 광학적 투과도 특성과 자외선 파장에서 발광이 가능한 장점을 가진다. 최근, ZnO박막 성장 기술이 상당히 발전하였지만, 아직까지도 p-형 ZnO박막 성장 기술은 충분히 발전하지 못하여 ZnO의 동종접합 LED는 아직 상용화되지 않고 있는 실정이다. 따라서, 많은 연구 그룹에서 p-GaN, p-SiC, p-diamond, p-Si 등과 같은 p-type 물질 위에 n-type ZnO를 성장시킨 이종접합 다이오드가 연구되고 있다. 특히, p-GaN의 경우 ZnO와의 격자 불일치 정도가 1.8 % 정도로 작다는 장점이 있어 많은 연구가 이루어 지고 있다. 일반적으로 c-축을 기반으로 한 극성ZnO 발광다이오드에서는 자발 분극과 압전 분극 현상에 의해 밴드 휨 현상이 발생하고, 이로 인해 전자와 정공의 공간적 분리가 발생하게 되어 발광 재결합 효율이 제한되고 있다는 문제가 발생한다. 따라서, 본 연구에서는 극성 (0001) 및 비극성 (10-10) n-ZnO/p-GaN 발광다이오드의 성장 및 발광 소자의 전기 및 광학적 특성에 대한 비교 연구를 진행하였다. 금속유기 화학증착법을 이용하여 c-면과 m-면 위에 각각 극성 (0001) 및 반극성 (11-22) GaN박막을 $2.0{\mu}m$ 성장시킨 후 Mg 도핑을 한 p-GaN을 $0.4{\mu}m$ 성장시켜 각각 극성 (0001) 및 반극성 (11-22) p-GaN템플릿을 준비하였다. 이후, N2분위기 $700^{\circ}C$에서 3분동안 열처리를 통하여 Mg 도펀트를 활성화시킨 후 원자층 증착법을 이용하여 동시에 극성 및 반극성 p-GaN의 위에 n-ZnO를 $0.11{\mu}m$ 성장시켜 이종접합구조의 발광소자를 형성하였다. 이때, 극성 (0001) p-GaN 위에는 극성의 n-ZnO 박막이 성장되는 반면, 반극성 (11-22) p-GaN 위에는 비극성 (10-10) n-ZnO 박막이 성장됨을 HR-XRD로 확인하였다. 극성 (0001) n-ZnO/p-GaN이종접합 발광다이오드의 전계 발광 스펙트럼에서는 430 nm 와 550 nm의 두 피크가 동시에 관찰되었다. 430 nm 대역의 파장은 p-GaN의 깊은 준위에서 발광하는 것으로 판단되며, 550 nm 피크 영역은 ZnO의 깊은 준위에서 발광되는 것으로 판단된다. 특히, 10 mA 이하의 저전류 주입시 550 nm의 피크는 430 nm 영역보다 더 큰 발광세기를 나타내고 있다. 하지만, 10 mA 이상의 전류주입 하에서는 550 nm의 영역보다 430 nm의 발광세기가 더욱 증가하는 것을 확인할 수 있었다. 이것은 ZnO의 밴드갭이 3.37 eV로 GaN의 밴드갭인 3.4 eV다 작기 때문에 우선적으로 ZnO의 깊은 준위에서 발광하는 550 nm가 더욱 우세하지만, 지속적으로 전류주입 증가에 따른 캐리어 증가시 n-ZnO에서 p-GaN로 전자가 넘어가며 p-GaN의 깊은 준위인 430 nm에서의 피크가 우세해지는 것으로 판단된다. 반면에, 비극성 (10-10) n-ZnO/반극성 (11-22) p-GaN 구조의 이종접합 발광다이오드로 전계 발광 스펙트럼에서는 극성 (0001) n-ZnO/p-GaN에 비하여 매우 낮은 전계 발광 세기를 나타내고 있다. 이는, 극성 n-ZnO/p-GaN에 비하여 비극성 n-ZnO/반극성 p-GaN의 결정성이 상대적으로 낮기 때문으로 판단된다. 또한, 20 mA 영역에서도 510 nm의 깊은 준위와 430 nm의 발광이 관찰되었다. 동일한 20 mA하에서 두 피크의 발광세기를 비교하면 430 nm의 영역은 극성 n-ZnO/p-GaN에 비하여 매우 낮은 값을 나타내고 있다. 이는 반극성 (11-22) p-GaN의 경우 극성 (0001) p-GaN에 비하여 우수한 p-형 특성에 기인한 것으로 판단된다.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.13 no.4
• /
• pp.176-184
• /
• 2011

Cold air on sloping surfaces flows down to the valley bottom in mountainous terrain at calm and clear nights. Based on the assumption that the cold air flow may be the same as the water flow, current models estimate temperature drop by regarding the cold air accumulation at a given location as the water-like free drainage. At a closed catchment whose outlet is blocked by man-made obstacles such as banks and roads, however, the water-like free drainage assumption is no longer valid because the cold air accumulates from the bottom first. We developed an empirical model to estimate quantitatively the effect of cold pool on nocturnal temperature in a closed catchment. In our model, a closed catchment is treated like a "vessel", and a digital elevation model (DEM) was used to calculate the maximum capacity of the cold pool formed in a closed catchment. We introduce a topographical variable named "shape factor", which is the ratio of the cold air accumulation potential across the whole catchment area to the maximum capacity of the cold pool to describe the relative size of temperature drop at a wider range of catchment shapes. The shape factor is then used to simulate the density profile of cold pool formed in a given catchment based on a hypsometric equation. The cold lake module was incorporated with the existing model (i.e., Chung et al., 2006), generating a new model and predicting distribution of minimum temperature over closed catchments. We applied this model to Akyang valley (i.e., a typical closed catchment of 53 $km^2$ area) in the southern skirt of Mt. Jiri National Park where 12 automated weather stations (AWS) are operational. The performance of the model was evaluated based on the feasibility of delineating the temperature pattern accurately at cold pool forming at night. Overall, the model's ability of simulating the spatial pattern of lower temperature were improved especially at the valley bottom, showing a similar pattern of the estimated temperature with that of thermal images obtained across the valley at dawn (0520 to 0600 local standard time) of 17 May 2011. Error in temperature estimation, calculated with the root mean square error using the 10 low-lying AWSs, was substantially decreased from $1.30^{\circ}C$ with the existing model to $0.71^{\circ}C$ with the new model. These results suggest the feasibility of the new method in predicting the site-specific freeze and frost warning at a closed catchment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.134-135
• /
• 2011

양자점은 전자와 양공을 3차원으로 속박 시키므로 기존의 bulk나 양자우물보다 양자점을 이용한 레이저 다이오드의 경우 낮은 문턱 전류, 높은 미분이득 및 온도 안전성의 장점이 있을 거라 기대되고 있다. 그러나, 양자점은 낮은 areal coverage 때문에 높은 속박효율을 얻지 못하고 있다. 이러한 양자점의 문제점을 해결하기 위해 양자점을 양자우물 안에 성장시켜 운반자들의 포획을 향상시키는 방법들이 연구되고 있다. 양자우물 안에 양자점을 넣으면 양자우물이 운반자들의 포획을 증가 시키고, 열적 방출도 억제하여 온도 안정성이 향상 되는 것으로 알려져 있다. 광통신 대역의 1.3 ${\mu}m$ 경우, GaAs계를 이용하여 InAs 양자점을 strained InGaAs 박막을 우물층으로 한 dot-in-a-well 구조의 연구는 몇몇 보고된 바 있다. 그러나 InP계를 사용하는 1.55 ${\mu}m$ 대역에서 dot-in-a-well구조의 연구는 아직 미미하다. 본 연구에서는 유기 금속 화학 증착법(metal organic chemical vapor deposition)을 이용하여 InP 기판 위에 InAs 양자점을 자발성장법으로 성장하였으며 dot-in-a-well 구조에서 우물층으로 1.35 ${\mu}m$ 파장의 $In_{0.69}Ga_{0.31}As_{0.67}P_{0.33}$ (1.35Q)를, 장벽층으로는 1.1 ${\mu}m$ 파장의 $In_{0.85}Ga_{0.15}As_{0.32}P_{0.68}$(1.1Q)를 사용하였다. 양자우물층과 장벽층은 모두 InP 기판과 격자가 일치하는 조건으로 성장하였다. III족 원료로는 trimethylindium (TMI)와 trimethylgalium (TMGa)을 사용하였으며 V족 원료 가스로는 $PH_3$ 100%, $AsH_3$ 100%를, carrier gas로는 $H_2$를 사용하였다. InP buffer층의 성장 온도는 640$^{\circ}C$이며 양자점 성장 온도는 520$^{\circ}C$이다. 양자점 형성은 원자력간 현미경(Atomic force microscopy)를 이용하여 확인하였으며, 박막의 결정성은 쌍결정 회절분석(Double crystal x-ray deffractometry)를 이용하여 확인하였다. 확인된 성장 조건을 이용하여 양자점 시료를 성장하였으며 광여기분광법(Photoluminescence)을 이용하여 광특성을 분석하였다. Fig. 1은 dot in a barrier 와 dot-in-a-well 시료의 성장구조이다. Fig. 1(a)는 일반적인 dot-in-a-barrier 구조로 InP buffer층을 성장하고 1.1Q를 100 nm 성장한 후 양자점을 성장하였다. 그 후 1.1Q 100 nm와 InP 100 nm로 capping하였다. Fig. 1(b)는 dot-in-a-well 구조로 InP buffer층을 성장하고 1.1Q를 100 nm 성장 후 1.35Q 우물층을 4 nm 성장하였다. 그 위에 InAs 양자점을 성장하였다. 그 후에 1.35Q 우물층을 4 nm 성장하고 1.1Q 100 nm와 InP 100 nm로 capping하였다. Fig. 2는 dot-in-a-barrier 시료와 dot-in-a-well 시료의 상온 PL data이다. Dot-in-a-barrier 시료의 PL 파장은 1544 nm이며 반치폭은 79.70 meV이다. Dot-in-a-well 시료의 파장은 1546 nm이며 반치폭은 70.80 meV이다. 두 시료의 PL 파장 변화는 없으며, 반치폭은 dot-in-a-well 시료가 8.9 meV 감소하였다. Dot-in-a-well 시료의 PL peak 강도는 57% 증가하였으며 적분강도(integration intensity)는 45%가 증가하였다. PL 데이터에서 높은 에너지의 반치폭 변화는 없으며 낮은 에너지의 반치폭은 8 meV 감소하였다. 적분강도 증가에서 dot-in-a-well 구조가 dot-in-a-barrier 구조보다 전자-양공의 재결합이 증가한다는 것을 알 수 있으며, 반치폭 변화로부터 특히 높은 에너지를 갖는 작은 양자점에서의 재결합이 증가 된 것을 알 수 있다. 이는 양자우물이 장벽보다 전자-양공의 구속력을 증가시키기 때문에 양자점에 전자와 양공의 공급을 증가시키기 때문이다. 따라서 낮은 에너지를 가지는 양자점을 모두 채우고 높은 에너지를 가지는 양자점까지 채우게 되므로, 높은 에너지를 가지는 양자점에서의 전자-양공 재결합이 증가되었기 때문이다. 뿐만 아니라 파장 변화 없이 PL peak 강도와 적분강도가 증가하고 낮은 에너지 쪽의 반치폭이 감소한 것으로부터 에너지가 낮은 양자점보다는 에너지가 높은 양자점에서의 전자-양공 재결합율이 급증하였음을 알 수 있다. 우리는 이와 같은 연구에서 InP계를 이용해 1.55 ${\mu}m$에서도 dot in a well구조를 성장 하여 더 좋은 특성을 낼 수 있으며 앞으로 많은 연구가 필요할 것이라 생각한다.